SkyRC e3 Duo Handleiding

Bekijk gratis de handleiding van SkyRC e3 Duo (3 pagina’s), behorend tot de categorie Batterij-oplader. Deze gids werd als nuttig beoordeeld door 13 mensen en kreeg gemiddeld 4.3 sterren uit 3 reviews. Heb je een vraag over SkyRC e3 Duo of wil je andere gebruikers van dit product iets vragen? Stel een vraag

INTRODUCTION

OPERATION

Select the proper charging current 0.5A/1A/1.5A/2.2Aby pressing the circular button.

Please refer to following steps to charge the battery.

4)

The charger starts charging. The charge status LED will glow to indicate charging is in progress.

5)

- 1 -- 2 -

INSTRUCTIONMANUAL

SK-100164

Multi Chemistry Charger

Example:

LiPo cell of 2200mAh Capacity; 1C=2200mA

(=2.2A) charge current. You can choose 2.2A

current to charge the battery.

ERROR MESSAGE

SPECIFICATION

2S Balance Port

Battery Type Indicator

Charge Current or Capacity Indicator

Select Charge Current or

Start Charge Processes

Select Battery Type

- 3 -

3S Balance Port

Select Battery Type

Select Charging Current

All LEDs flash white ONCE and stop 2 seconds in

cycle

All LEDs flash white TWICE and stop 2 seconds in

cycle

All LEDs flash white THREE TIMES and stop 2

seconds in cycle

ProblemLED Blinking Times

The charging time is longer than 120min

Voltage of one cell in the battery pack is too low

Voltage of one cell in the battery pack is too high

AC Input

Battery Type

Cell Count

Charge Current

Cell Terminate Voltage

Circuit Power

Current Drain for Balancing

Dimension

Weight

100-240V

LiPo/LiFe/LiHV

2-3 CELLS

0.5A/1A/1.5A/2.2A

LiPo: 4.2V ± 0.02V / LiFe: 3.6V ± 0.02V

LiHV: 4.35V ± 0.02V

20Wx2

Max. 200mA

108x76x50mm

500g

Thank you for your choice of the SKYRC e3 Duo, 100-240V AC balance charger. This unit is simple to use

but its operation does require some knowledge on the part of the user. Please read this entire operating

manual completely and attentively before using this product, as it covers a wide range of information on

operating and safety.

SKYRC e3 Duo Charger is an economic, high quality 100-240V AC balance charger, designed for

charging LiPo, LiFe and LiHV batteries from 2-3 cells in balance mode. The circuit power is 20W for each

channel and max charge current can reach to 2.2A. There are four kinds of charge current

0.5A/1A/1.5A/2.2A that can be selected. You could select the proper charge current according to battery

capacity.

SKYRC e3 Duo comes with the built in power supply. You can connect the AC power cord to the AC

socket (100-240V AC) directly.

Insert the AC power cord into the charger.

1)

2)

3)

Insert the AC cord into a wall socket (100-240V).

All LEDS will light for one second, then battery

type LED(default LiPo) and the charge current

LED(default 1A) will glow constant white.

Connect battery balance wire to balance port

which is in front side of the charger, select the

battery type LiPo/LiFe/LiHV by press “BATT”

button.

The recommended charge rate is 1C (battery

capacity = charge current). 1C means: capacity

value = charge current.

EXPLAINATION OF LED STATUS

Capacity＜25% 25% capacity indictor LED flashing

25%≤Capacity＜50% 50% capacity indictor LED flashing

50%≤Capacity＜75% 75% capacity indictor LED flashing

75%≤Capacity＜100% 100% capacity indictor LED flashing

0.5A Flashes white ONCE and stop 1 second in cycle.

1.0A Flashes white TWICE and stop 1 second in cycle.

1.5A Flashes white THREE TIMES and stop 1 second in cycle.

2.2A Flashes white FOUR TIMES and stop 1 second in cycle.

Remark:

The capacity indicator LED flash �mes shows the charge current you set.

When the battery is fully charged, the charge status LED will glow constant WHITE. Unplug the

battery from the charger and press the circular button once, the charger will be ready to charge

another battery.

6) During the charging process, if you want to stop charging, press the circular button once.

If the charger encounters a problem, all LEDs will flash white to alert you the errors. In this case,

please disconnect the power cord from the wall socket and unplug the battery from the charger.

CAUTION:

TO 100-240V AC

Socket

This diagram shows the correct way to

connect your battery to the e3 Duo

charger while charging in balance mode.

Product specificaties