Schneider Back-UPS BE750G Handleiding
Pagina's 8 UPS
Bekijk de handleiding van Schneider Back-UPS BE750G gratis online of download de PDF. Deze handleiding is 0 keer bekeken. Vraag over dit model? Stel een vraag
Installation and Operation
Back-UPS
™
BE750G Series
Safety
Specifications
This UPS is intended for indoor use only.
Do not operate this UPS in direct sunlight, in contact with fluids, or where there
is excessive dust or humidity.
Be sure the air vents on the UPS are not blocked. Allow adequate space for
proper ventilation.
The battery typically lasts for two to five years. Environmental factors impact battery life. Elevated ambient
temperatures, poor quality utility power, and frequent short duration discharges will shorten battery life.
Connect the Back-UPS power cable directly to a wall outlet. Do not use surge protectors or extension cords.
Input
Voltage120 VacNominal
Frequency50 Hz/60 Hz auto sensing
Brownout Transfers92 Vrms Typical
Over-voltage Transfer139 Vrms Typical
Output
UPS Capacity
(5 battery backup outlets)
750 VA, 450 W
Total Amperage (all outlets)12 A (including UPS output)
Voltage - On Battery115 Vrms ± 8% step approximated sine wave
Frequency - On Battery50 Hz/60 Hz ± 1 Hz
Transfer Time6 ms Typical, 10 ms maximum
Protection and
Filtering
AC Surge ProtectionFull time, 354 Joules
Phone/DSL/FAX surge protectionSingle line (2 wire)
Cable/CAT V/DSS surge protectionOne coax input/output
Network surge protection10/100 Base -T ethernet
EMI/RFI FilterFull time
AC InputResettable circuit breaker
Battery
TypeSealed, maintenance-free, lead acid
Replacement battery cartridge RBC17
Average Life3 - 5 years depending on the number of discharge cycles and
environmental temperature
Physical
Net Weight11 lb (5 kg)
Dimensions
Length x Width x Height
14 in x 7 in x 4 in
36 cm x 18 cm x 9 cm
Operating Temperature32º F to 104º F (0º C to 40º C)
Storage Temperature5º F to 113º F (–15º C to 45º C)
Operating Relative Humidity0 to 95% non-condensing humidity
Operating Elevation0 to 10,000 ft (0 to 3000 m)
EMC
Compliance
This device complies with part 68 and part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesired operation.
Back-UPS BE750G Series2
Connect the Battery
The Back-UPS is shipped with one battery cable disconnected. Remove the “Stop! Connect the Battery” label that
covers the outlets. Prior to connecting any equipment to the unit, connect the battery cable to the unused battery
terminal. It is normal for small sparks to be seen when the battery cable is connected to the battery terminal.
Wall Mount Installation
• Horizontal installation, use 2 screws 5.9" (150 mm) apart.
• Vertical installation, use 2 screws 5.5" (140 mm) apart.
• Allow 5/16" (8 mm), of the screw to protrude from the wall.
Connect Equipment
Battery Backup + Surge Protection Outlets
Battery backup outlets provide protection to connected
equipment when the Back-UPS is turned on and
connected to utility power.
Battery backup outlets receive power from the
Back-UPS for a limited period of time when a power
outage, or brownout condition occurs.
Battery backup outlets provide protection from power
surges or spikes.
Connect a computer, monitor and other peripheral devices to the outlets.
Surge Protection Outlets
Surge protection outlets provide protection to connected equipment when the Back-UPS is connected to utility
power, and is switched on or off.
Surge protection outlets provide protection from power surges or spikes.
Connect a printer, scanner or other peripheral devices to the surge protection outlets.
Press the battery compartment cover
release tab located on the rear side of the
unit. Slide the battery cover off.
Connect the battery cable securely
to the battery terminal.
Reinstall the battery compartment
cover. Be sure that the release tab
locks into place.
bu076a
bu077a
bu083a
bu207a
Back-UPS
Master
Enable
Battery Backup + Surge Protection
MASTER
Surge Protection
Controlled By MASTER
Back-UPS BE750G Series3
Connect Modem/Telephone/DSL/FAX/10/100
Base-T Network Cable
The Back-UPS protects a single line, 2 wire telephone
line, including a Digital Subscriber Line (DSL), a
modem, a 10/100 Base-T ethernet, or a FAX machine
from power surges when connected through the
Back-UPS coaxial connectors.
PowerChute
™
Personal Edition Software
Overview
PowerChute Personal Edition Software allows you to use your computer to access additional power protection and
management features of the Back-UPS.
Using PowerChute, you can:
• Preserve work in progress during a power outage by putting your computer into Hibernate mode.
When the power returns, the computer will appear exactly as it did before the power outage.
• Congure the Back-UPS management features, such as power-saving outlets, shutdown
parameters, audible alarms, and more.
• Monitor and view the status of the Back-UPS, including the estimated runtime, power
consumption, power event history, and more.
Available features will vary by Back-UPS model and operating system.
If you choose not to install PowerChute, the Back-UPS will still provide backup power and power protection to
connected equipment. However, you will only be able to configure a limited number of features using the display
interface.
Compatibility
PowerChute is compatible with Windows operating systems only. For a detailed list of supported operating
systems, go to www.apc.com, select Software & Firmware.
For Mac operating systems, we recommend using the native shutdown application (within System Preferences)
which recognizes your battery backup and allows you to configure shutdown of your system during power outages.
To access this application, connect a USB cable from the Back-UPS
DATA PORT (POWERCHUTE PORT) to a USB
port on your computer, and see the documentation provided with your computer.
Installation
Connect the Back-UPS to a computer using a USB cable. Plug one end into the PC OWERHUTE PORTon the rear
panel of the Back-UPS and the other into a USB port on your computer.
Insert the PowerChute CD into your computer and follow the on-screen instructions. If your Back-UPS did not
come with a PowerChute CD, download the software from www.apc.com, select Software & Firmware.
bu209a
CAUTION-Refer to bottom
of unit for safety markings.
Building
Wiring Fault
PowerChute
USB Port
Circuit Breaker
Push to Reset
Cable In
Cable Out
Out
In
Network/DSL/Modem/FAX
Product specificaties
| Merk: | Schneider |
| Categorie: | UPS |
| Model: | Back-UPS BE750G |
Heb je hulp nodig?
Als je hulp nodig hebt met Schneider Back-UPS BE750G stel dan hieronder een vraag en andere gebruikers zullen je antwoorden