Schneider Back- BE650G1 Handleiding

Bekijk gratis de handleiding van Schneider Back- BE650G1 (2 pagina’s), behorend tot de categorie UPS. Deze gids werd als nuttig beoordeeld door 3 mensen. Heb je een vraag over Schneider Back- BE650G1 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Inventory

Safety and General Information

Inspect the package contents upon receipt. Notify the

carrier and dealer if there is any damage.

Read the Safety Guide supplied with this unit before installing the

UPS.

• This UPS is intended for indoor use only.

• Do not operate this UPS in direct sunlight, in contact with fluids, or where there is

excessive dust or humidity.

• Be sure the air vents on the UPS are not blocked. Allow adequate space for proper

ventilation.

• The battery typically lasts for two to three years. Environmental factors impact

battery life. Elevated ambient temperatures, poor quality AC power, and frequent

short duration discharges will shorten battery life.

• Connect the UPS power cable directly to a wall outlet. Do not use surge protectors

or extension cords.

Specifications

Connect the Battery

The Back-UPS is shipped with one battery cable disconnected. Remove the “Stop!

Connect the Battery” label that covers the outlets. Prior to connecting any equipment

to the unit, connect the battery cable to the unused battery terminal. It is normal for

small sparks to be seen when the battery cable is connected to the battery terminal.

Wall Mount Installation

• Horizontal installation, use 2 screws 7.3" (186.3 mm) apart.

• Vertical installation, use 2 screws 5.4" (137.2 mm) apart.

• Allow 5/16” (8 mm), of the screw to protrude from the wall.

Replace Battery

Use only approved APC by Schneider Electric replacement battery cartridges.

Deliver used batteries to a battery replacement facility in the packaging provided by

APC by Schneider Electric with the replacement battery cartridge. To order

replacement battery cartridges contact APC by Schneider Electric.

Connect Equipment

Battery Backup + Surge Protection outlets

Battery backup outlets provide protection to connected equipment when the

Back-UPS is turned on and connected to AC power.

Battery backup outlets receive power from the Back-UPS for a limited period of time

when a power outage, or brownout condition occurs.

Battery backup outlets provide protection from power surges or spikes.

Connect a computer, monitor and other peripheral devices to the outlets.

Surge Protection outlets

Surge protection outlets provide protection to connected equipment when the

Back-UPS is connected to AC power, and is switched on or off.

Surge protection outlets provide protection from power surges or spikes.

Connect a printer, scanner or other peripheral devices to the surge protection outlets.

Connect telephone line

The Back-UPS protects equipment connected to a telephone line from power surges

when connected through the Back-UPS coaxial connectors.

PowerChute

™

Personal Edition Software

Overview

Use PowerChute Personal Edition software to configure the UPS settings.

Protect your computer and other equipment during a power outage. During a power

outage, PowerChute will save any open files on your computer and safely shut it

down. When power is restored, it will restart the computer.

Configure the UPS to use features such as power-saving outlets, shutdown

configuration, and alarms.

Monitor the UPS for power usage and power events.

Note: PowerChute is only compatible with a Windows operating system. If you are

using a Mac OSX, use the native shutdown feature to protect your system. See the

documentation provided with your computer.

Installation

Use a USB cable to connect the Data port on the rear panel of the UPS to the USB port

on your computer.

If the Back-UPS came with CD into your computer and a PowerChute CD, insert the

follow the on-screen instructions.

If the Back-UPS did not come with a PowerChute CD, go to www.apc.com and

download the software free of charge.

Turn On the Back-UPS

Press the POWER ON button located on the top of the Back-UPS. The Power On/

Replace Battery LED will illuminate and a single short beep will be audible to

indicate that the Back-UPS is providing protection for connected equipment.

The Back-UPS battery charges fully during the first 16 hours while connected to AC

power. The Back-UPS battery will charge while the Back-UPS is switched on or off

and is connected to AC power. Do not expect full battery run capability during the

initial charge time.

If the red Building Wiring FaultLED located on the side of the Back-UPS

illuminates, do not operate the Back-UPS. Have a qualified electrician correct the

building wiring fault.

Warranty

The standard warranty is two (2) years from the date of purchase. Schneider Electric

IT (SEIT) standard procedure is to replace the original unit with a factory

reconditioned unit. Customers who must have the original unit back due to the

assignment of asset tags and set depreciation schedules must declare such a need at

first contact with an SEIT Technical Support representative. SEIT will ship the

replacement unit once the defective unit has been received by the repair department,

or cross ship upon the receipt of a valid credit card number. The customer pays for

shipping the unit to SEIT. SEIT pays ground freight transportation costs to ship the

replacement unit to the customer.

Input

Voltage120 VacNominal

Frequency60 Hz +

3

Brownout Transfers92 Vac Typical

Over-voltage Transfer139 Vac Typical

Output

UPS Capacity

(4 battery backup outlets)

BE450G: 450 VA, 257 W;

BE550G: 550 VA, 330 W;

BE650G1: 650 VA, 390 W

Total Amperage (all outlets)12 A (including UPS output)

Voltage - On Battery115 Vac ± 8%

Frequency - On Battery60 Hz +

1

Transfer Time6 ms Typical, 10 ms maximum

Protection

and

Filtering

AC Surge ProtectionFull time, 340 Joules

EMI/RFI FilterFull time

AC InputResettable circuit breaker

Battery

TypeSealed, maintenance-free, lead acid

BE450G: RBC114

BE550G: RBC110

BE650G1: RBC17

Average Life3 - 5 years depending on the number of

discharge cycles and environmental

temperature

Physical

Net WeightReplacement battery cartridge

BE450G: 10 lb (4.7 kg)

BE550G: 12 lb (5.5 kg)

BE650G1: 14 lb (6.2 kg)

Dimensions

Length x Width x Height

12 in x 7 in x 3 in

30 cm x 18 cm x 9 cm

Operating Temperature32º F to 104º F (0º C to 40º C)

Storage Temperature5º F to 113º F (–15º C to 45º C)

Operating Relative Humidity0 to 95% non-condensing humidity

Operating Elevation0 to 10,000 ft (0 to 3000 m)

EMI

Compliance

This device complies with part 68 and part 15 of the FCC rules.

Operation is subject to the following two conditions: (1) This device

may not cause harmful interference, and (2) This device must accept any

interference received, including interference that may cause undesired

operation.

 Press the battery compartment cover

release tab located on the rear side of the

unit. Slide the battery cover off.

 Connect the battery cable securely to the

battery terminal.

 Reinstall the battery compartment cover.

Be sure that the release tab locks into place.

bu075c

Back-UP

S

bu064a

bu065a

bu066a

bu202a

Back-UPS

Battery Backup + Surge Protection

Surge Protection

bu201b

CAUTION-Refer to bottom

of unit for safety markings.

Circuit

Breaker

Building

Wiring Fault

PowerChute

USB Port

Tel

Out

Push to

Reset

Tel

In

User Manual Back-UPS

™

BE 450G/550G/650G1

Product specificaties