Rane MC 22 Handleiding
Rane
Mengpaneel
MC 22
Bekijk gratis de handleiding van Rane MC 22 (11 pagina’s), behorend tot de categorie Mengpaneel. Deze gids werd als nuttig beoordeeld door 7 mensen en kreeg gemiddeld 4.6 sterren uit 4 reviews. Heb je een vraag over Rane MC 22 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/11
Manual-1
OPERATORS MANUAL
QUICK START
Shredded, this document makes excellent packing material. In its present form, it makes interesting and useful reading.
If you run out of patience quickly, at least read this part to make sure you don’t exterminate everything within a two mile
radius by doing something wrong.
Attach one or two channels of inputs and outputs to the respective connectors on the rear. This device uses low imped-
ance balanced line drivers. Do not connect the XLR “+” or “–” output pins to ground, as this may cause the power supply
to shut down. For unbalanced use, leave the unused output pin (“+” or “–”) unterminated.
With the RATIO turned all the way down at 1:1, THRESHOLD turned all the way up to 20 dBu, and the LEVEL
controls in their center at 0 dB, you have an expensive patch cord.
While sending a signal to the MC 22, adjust the INPUT LEVEL so the +4 dBu LED lights occasionally, but the OL
LED does not light. Now increase the RATIO to something useful, like 2:1 (with the control set at 2, the Ratio is 2:1; at 5,
it is 5:1.) Adjust the THRESHOLD to the point you want the Compressor to kick in. The GAIN REDUCTION meter
reads the amount of signal compression.
Both Compressors will activate by the source material applied to either Channel if the LINK switch is ON. This is the
preferred setting for stereo program material.
WEAR PARTS: This product contains no wear parts.
MC 22
STEREO COMPRESSOR
Manual-2
INPUT LEVEL control
This controls the overall level. Unity gain is
reached at “0”. With signal applied, set this
control so the +4 dBu LED lights occasion-
ally. If the OL (overload) LED flashes, turn
the INPUT LEVEL control down.
THRESHOLD control
This control sets the point at which the Input
signal level causes the Compressor to
become active. See Figure 1 on page
Manual-4.
COMPRESSOR
ACTIVE/BYPASS switch
This switch compares compressed and non-
compressed signal. There is one for each
Channel. The INPUT LEVEL remains active
regardless of switch position.
LED
This illuminates whenever noise reduction is
active. This automatic downward expander
circuit acts like a gate to keep the system
quiet when no signal is present. When the
input level drops below -55 dBu, downward
expansion occurs at a ratio of 2:1. See
Figure 3 on page Manual-5.
RATIO control
Once the threshold is exceeded, the ratio of
input change to output change is determined
by this control. The compressor has no
effect when set at 1:1. But at 10:1, it takes
a 10 dB input signal increase above the
Threshold to produce a 1 dB increase in
Output Gain. See Figure 2 on page
Manual-4.
GAIN REDUCTION LEDs
These LEDs show the amount of average
signal reduction in dB. This aids in setting
the THRESHOLD and RATIO controls by
showing how much compression is occuring.
CHANNEL 2 OUTPUT
Same as Channel 1 Output.
CHANNEL 2 INPUT
Same as Channel 1 Input.
Manual-3
Cable Wiring
In agreement with IEC and AES/ANSI
standards, XLR wiring convention is pin 2
Positive (hot), pin 3 Negative (cold), and
pin 1 chassis grounded and signal grounded
(to allow unbalanced operation). The XLR
case is chassis grounded.
Power ON switch and LED
Your basic, straightforward power switch.
When the switch is depressed and the
yellow LED is lit, the MC 22 is ready to go.
CHANNEL 2 controls
These duplicate the controls in Channel 1.
LINK switch
Switch this to ON when using stereo
material. This activates both Compressors
when either Channel’s signal exceeds the set
Threshold, preserving stereo imaging.
CHANNEL 1 INPUT
Choose between the balanced XLR or the
balanced/unbalanced ¼" TRS jacks, but
only use one. Inserting a ¼" TS jack will
work—however—use balanced lines,
especially when connecting cables over 10
feet in length. Consult SOUND SYSTEM
INTERCONNECTION on page Manual-10.
CHANNEL 1 OUTPUT
Use either the balanced XLR or the unbal-
anced ¼" TS jack. Using both types of
Outputs are permissible to drive two devices,
such as an amplifier and a recorder.
This
device uses low impedance balanced line
drivers. connect the XLR “+” or “–”
output pins to ground, as this may cause the
power supply to shut down. For unbalanced
use, leave the unused output pin (“+” or
“–”) unterminated.
Product specificaties
| Merk: | Rane |
| Categorie: | Mengpaneel |
| Model: | MC 22 |
Heb je hulp nodig?
Als je hulp nodig hebt met Rane MC 22 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Mengpaneel Rane
18 Juni 2025
18 Juni 2025
18 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
Handleiding Mengpaneel
- NutriBullet
- Moulinex
- Alesis
- Alecto
- Klark Teknik
- Kramer
- Atlas Sound
- SPL
- JBL
- Cloud
- Exquisit
- Mackie
- Black And Decker
- Alpina
- Bogen
Nieuwste handleidingen voor Mengpaneel
17 Juni 2025
3 Juni 2025
21 Mei 2025
21 Mei 2025
21 Mei 2025
20 Mei 2025
20 Mei 2025
20 Mei 2025
19 Mei 2025
12 Mei 2025