Pyle PP444 Handleiding

Pyle Receiver PP444

Lees hieronder de 📖 handleiding in het Nederlandse voor Pyle PP444 (23 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 15 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/23

BPP205 PAR64 18x15W 5-1 PENTA IR DMX

Ref. nr.: 151.233

INSTRUCTION MANUAL

GEBRUIKSAANWIJZING

GEBRAUCHSANLEITUNG

MANUAL DE INSTRUCCIONES

MANUEL D'INSTRUCTIONS

V1.0

ENGLISH

Congratulations to the purchase of this Beamz light effect. Please read this manual thoroughly prior to using the unit in order to

benefit fully from all features.

Read the manual prior to using the unit. Follow the instructions in order not to invalidate the warranty. Take all precautions to

avoid fire and/or electrical shock. Repairs must only be carried out by a qualified technician in order to avoid electrical shock.

Keep the manual for future reference.

- Prior to using the unit, please ask advice from a

specialist. When the unit is switched on for the first time,

some smell may occur. This is normal and will disappear

after a while.

- The unit contains voltage carrying parts. Therefore do

NOT open the housing.

- Do not place metal objects or pour liquids into the unit

This may cause electrical shock and malfunction.

- Do not place the unit near heat sources such as

radiators, etc. Do not place the unit on a vibrating

surface. Do not cover the ventilation holes.

- The unit is not suitable for continuous use.

- Be careful with the mains lead and do not damage it. A

faulty or damaged mains lead can cause electrical shock

and malfunction.

- When unplugging the unit from a mains outlet, always

pull the plug, never the lead.

- Do not plug or unplug the unit with wet hands.

- If the plug and/or the mains lead are damaged, they

need to be replaced by a qualified technician.

- If the unit is damaged to such an extent that internal

parts are visible, do NOT plug the unit into a mains outlet

and DO NOT switch the unit on. Contact your dealer. Do

NOT connect the unit to a rheostat or dimmer.

- To avoid fire and shock hazard, do not expose the unit to

rain and moisture.

- All repairs should be carried out by a qualified technician

only.

- Connect the unit to an earthed mains outlet (220-

240Vac/50Hz) protected by a 10-16A fuse.

- During a thunderstorm or if the unit will not be used for a

longer period of time, unplug it from the mains. The rule

is: Unplug it from the mains when not in use.

- If the unit has not been used for a longer period of time,

condensation may occur. Let the unit reach room

temperature before you switch it on. Never use the unit in

humid rooms or outdoors.

- During operation, the housing becomes very hot. Do not

touch it during operation and immediately after.

- To prevent accidents in companies, you must follow the

applicable guide lines and follow the instructions.

- Secure the unit with an extra safety chain if the unit is

ceiling mount. Use a truss system with clamps. Make

sure nobody stands in the mounting area. Mount the

effect at least 50cm away from inflammable material and

leave at least 1 meter space on every side to ensure

sufficient cooling.

- This unit contains high intensity LEDs. Do not look into

the LED light to prevent damage to your eyes.

- Do not repeatedly switch the fixture on and off. This

shortens the life time.

- Keep the unit out of the reach of children. Do not leave

the unit unattended.

- Do not use cleaning sprays to clean switches. The

residues of these sprays cause deposits of dust and

grease. In case of malfunction, always seek advice from

a specialist.

- Only operate the unit with clean hands.

- Do not force the controls.

- If the unit has fallen, always have it checked by a

qualified technician before you switch the unit on again.

- Do not use chemicals to clean the unit. They damage the

varnish. Only clean the unit with a dry cloth.

- Keep away from electronic equipment that may cause

interference.

- Only use original spares for repairs, otherwise serious

damage and/or dangerous radiation may occur.

- Switch the unit off prior to unplugging it from the mains

and/or other equipment. Unplug all leads and cables

prior to moving the unit.

- Make sure that the mains lead cannot be damaged when

people walk on it. Check the mains lead before every use

for damages and faults!

- The mains voltage is 220-240Vac/50Hz. Check if power

outlet match. If you travel, make sure that the mains

voltage of the country is suitable for this unit.

- Keep the original packing material so that you can

transport the unit in safe conditions

This mark attracts the attention of the user to high voltages that are present inside the housing and that are of sufficient

magnitude to cause a shock hazard.

This mark attracts the attention of the user to important instructions that are contained in the manual and that he should

read and adhere to.

DO NOT LOOK DIRECTLY INTO THE LENS. This can damage your eyes. Persons who are subject to epileptic attacks

should be aware of the effects that this light effect may have on them.

The unit has been certified CE. It is prohibited to make any changes to the unit. They would invalidate the CE certificate and

their guarantee!

NOTE: To make sure that the unit will function normally, it must be used in rooms with a temperature between 5°C/41°F and

35°C/95°F. 

Electric products must not be put into household waste. Please bring them to a recycling centre. Ask your local authorities or your

dealer about the way to proceed. The specifications are typical. The actual values can slightly change from one unit to the other.

Specifications can be changed without prior notice.

UNPACKING INSTRUCTION

CAUTION! Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are

present, and have been received in good condition. Notify the shipper immediately and retain packing material for inspection if

any parts appear damage from shipping or the package itself shows signs of mishandling. Save the package and all packing

materials. In the event that a fixture must be returned to the factory, it is important that the fixture be returned in the original

factory box and packing.

If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The

arising condensation water might damage your device. Leave the device switched off until it has reached room temperature.

POWERSUPPLY

On the label on the backside of the controller is indicated on this type of power supply must be connected. Check that the mains

voltage corresponds to this, all other voltages than specified, the light effect can be irreparably damaged. The controller must

also be directly connected to the mains and may be used. No dimmer or adjustable power supply.

INSTALLATION

Attention:

 The installation of the xture has to be built and constructed in a way that it can hold 10 times the weight

for 1 hour without any harming deformation.

 The installation must always be secured with a secondary safety attachment, e.g. an appropriate catch net.

This secondary safety attachment must be constructed in a way that no part of the installation can fall down

if the main attachment fails.

 Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging

and servicing.

 The operator has to make sure that safety-relating and machine-technical installations are approved by an

expert before taking into operation for the first time and after changes before taking into operation another

time.

 The operator has to make sure that safety-relating and machine-technical installations are approved by a

skilled person once a year.

 The fixture should be installed in the position where persons cannot reach and where persons may walk by

or be seated.

CAUTION: Please consider the respective national norms

during the installation! The installation must only be

carried out b

an authorized em

ee or dealers!

CAUTION: When installing the device, make sure there is no

highly in inflammable material (decoration articles,

etc.) in between a distance of min 0.5 meter.

Product specificaties

Merk:	Pyle
Categorie:	Receiver
Model:	PP444
Kleur van het product:	Grijs
Gewicht:	400 g
Breedte:	90 mm
Diepte:	26 mm
Hoogte:	54 mm
Connectiviteitstechnologie:	Bedraad
DC voltage input:	12 V
Audio-uitgangskanalen:	1.0 kanalen
Frequentiebereik:	20 - 20000 Hz
Signaal/ruis-verhouding:	70 dB
Totale harmonische vervorming (THD):	0.08 procent
AC-ingangsspanning:	110 V
Input sensitiviteit:	3 mV
Piekvermogen per kanaal:	- W
Synchronisatie ingangsimpedantie:	50000 Ohm
Speakers connectiviteit type:	RCA
Output impedance:	10000 Ohm