Projecta HDBT350 Handleiding
Projecta
Niet gecategoriseerd
HDBT350
Bekijk gratis de handleiding van Projecta HDBT350 (8 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 25 mensen en kreeg gemiddeld 4.4 sterren uit 13 reviews. Heb je een vraag over Projecta HDBT350 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/8
Tray Fitting Instructions to suit Auxiliary battery for
Holden Colorado & Colorado 7
Years: 2011 onwards
Models: RGD 2.8 Litre Diesel
HEAVY DUTY DUAL BATTERY TRAY
P/No. HDBT350
2
IMPORTANT SAFETY INFORMATION
Please read this instruction thoroughly before fitting the tray.
This product is recommend to be fitted by a workshop or qualified mechanical person.
WARNINGS
• Before installation, make sure that the vehicle is stationary and the wheels chocked.
• Be careful when laying wires, not to cause any electrical shorts or wire breakage.
• After installation ensure the bonnet can close without hitting the newly installed battery
and battery tray.
SPECIFICATIONS
Max Battery Size (mm) L265 x W174 X H200
Max Battery Weight 19.6Kg
Recommended batteries Optima D34 & Exide Orbital
(Fully Sealed AGM type due to close proximity to wiring and computer)
Approximate fitting time 2 hours
Special tools Right Angle Drill
Recommended Dual P/n: IDC25, DBC150, VSR200
Battery System
Tray Location Engine Bay, Passenger side near firewall
KIT INCLUDES
Hardware
7 x M6 Bolts
1 x M6 Bolt Long
4 x M6 Nuts
1 x M6 Washer
2 x M8 Bolts
1 x M8 Nut
1 x M8 Body Washer
*Need to supply
1 x Cushion Clamp
2 x M6 RIVNUTS are
for isolator mount
Hardware
3 x M6 Bolts Counter Sunk
2 x M6 Bolts, Hex head Short
4 x M6 Nuts
1 x M6 Body Washer
Special Top
Mount
Tray
Isolator
Mount
Bolt Bracket
Right Angle
Bracket
T Bracket
J Bolts
Computer Mount Bracket for late 2013 models
3
FITTING INSTRUCTIONS
1. Make sure that the vehicle is stationary, the engine is switched off and cool.
Disconnect the negative and positive battery terminal from the main battery.
2. Remove the original battery & battery tray and 1 bolt only from the computer
mount closest to the tray.
3. Disconnect multi-pin plug behind computer and move to fit along firewall and
secure (Temporarily).
4. To allow clearance of the new battery tray.
a. You may need to bend L bracket on firewall.
b. Manipulate air-con pipe.
c. Unclip the loom behind factory tray.
5. Fit Tray with lower arm between brake lines and inner guard.
6. Place 3 x M6 Bolts through special bolt bracket then into the existing holes on the
inner guard, now push the bolts through the lower arm of the tray and hand
tighten M6 Nuts.
7. Place 2 x M6 Bolts into plate on the front of tray. Do not tighten yet. If fitting
this to a July 2012 or older Colorado go to step 12. Follow these steps for
August 2012 onwards.
Product specificaties
| Merk: | Projecta |
| Categorie: | Niet gecategoriseerd |
| Model: | HDBT350 |
Heb je hulp nodig?
Als je hulp nodig hebt met Projecta HDBT350 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd Projecta
31 Mei 2023
18 Mei 2023
13 Mei 2023
8 Mei 2023
28 April 2023
27 April 2023
26 April 2023
16 April 2023
15 April 2023
10 April 2023
Handleiding Niet gecategoriseerd
- Triax
- Irradio
- Lancom
- MQ
- Eurosound
- Dobot
- MagTek
- Ag Neovo
- Octavio
- Canyon
- Creality3D
- Senseca
- Gaggenau
- Tablo
- Vroomshoop
Nieuwste handleidingen voor Niet gecategoriseerd
31 Juli 2025
31 Juli 2025
31 Juli 2025
31 Juli 2025
31 Juli 2025
31 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025