Projecta SC110 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Projecta SC110 (12 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 117 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/12
1
SOLAR CONTROLLER
P/No. SC110
12 VOLT
4 STAGE CHARGING
2
WARNINGS – IMPORTANT PLEASE READ
• SC110 is designed for indoor use only
• Use SC008 or SC015 for outdoor applications
• Do not disassemble the controller. Take to a qualified person if the unit requires repairing.
• Lead acid batteries can be dangerous. Ensure no sparks or flames are present when working
near batteries
• Eye protection should always be used. Never short circuit the battery
• Given sufficient light solar panels always generate energy even when they are disconnected.
• Accidental ‘shorting’ of the terminals or wiring can result in sparks causing personal injury or a fire
hazard. We recommend that you cover up the panel(s) with some sort of soft cloth so you can block
all incoming light during the installation. This will ensure that no damage is caused to the Solar
Panel or Battery if the wires are accidentally short circuited
• Always install a battery fuse on each circuit including the solar controller
MOUNTING THE DEVICE
The Solar Controller is mounted as below
The quickest and easiest way to mount the unit is to use the two plastic spacers and self tapping
screws supplied and mount the unit to a flat surface.
5723
58
Fig 1.
3
FEATURES
• 4 Stage charging ensures the battery is charged to the optimum level
• Advanced MCU control pulse width modulated (PWM) technology, high efficiency operation
• Programmable for Gel, AGM, Conventional lead-acid (WET) and Calcium Batteries
• Built in regulator to prevent your battery from being overcharged. Overcharging occurs when the
charge voltage is unregulated. This can result in premature battery failure
• In built regulator prevents your battery from being under charged, in the solar energy field, battery
undercharge often occurs, especially on some conventional Lead Acid or Calcium batteries; the unit
provides an automatic equalization feature for deeply drained conventional Lead Acid battery or
Calcium battery, as well as provides a cycling automatic equalizing feature every 28 days
• These solar controllers can be connected to the battery permanently to keep the battery fully
charged by using a process called “floating”. This means the controller will stop charging when the
battery is full and will automatically start charging the battery as required. This process will also
reduce water loss and help prevent the battery from ‘drying out’
• Protects your battery from discharge at night. Under low light or no light conditions the solar panel
voltage could be less than the battery voltage. The unit contains a special circuit which prevents
current flowing back from the battery and into the solar panel
• Colored LED’s to easily indicate the operational status and battery conditions
• Digital LCD to directly display battery voltage, charging current, charging capacity (Amp hour),
battery types, full charge and faulty codes
• Provides external battery temperature sensor (Optional)
• Multi charging protections against reverse polarity, short circuit, over temperature, over voltage, etc.
• Surface Mount or Flush Panel Mount options
• Conformal-coating circuit boards and plated terminals protect the unit in hostile environments
For use with 12Volt Solar Panel Only. Suitable for solar panels up to
120 Watts (SC110).
SOLAR CHARGE CONTROLLER
AMP/VOLT
BATTERY
TYPE
Hold for 3 seconds
for settings
CHA RG ING S T AT U S BAT T ERY COND IT IO N
12 VOLT
10 AMP
P/No. SC110
Fig 2.


Product specificaties

Merk: Projecta
Categorie: Niet gecategoriseerd
Model: SC110

Heb je hulp nodig?

Als je hulp nodig hebt met Projecta SC110 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Projecta

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd