Prier C-634 Handleiding

Bekijk gratis de handleiding van Prier C-634 (2 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 2 mensen en kreeg gemiddeld 5.0 sterren uit 6 reviews. Heb je een vraag over Prier C-634 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

PRIER Products, Inc.

4515 E 139th St.

Grandview, MO 64030

800-362-9055 Fax: 800-362-1463

www.PRIER.com

Installation, Operation & Maintenance Instructions for the

PRIER C-634 Heavy Commercial Wall Hydrant

*Please leave this sheet for the property owner*

Thank you for purchasing the PRIER C-634 Heavy Commercial Wall Hydrant, the nest quality commercial

hydrant available. Your C-634 will provide you years of dependable service with little or no maintenance.

Please note: Your C-634 hydrant has drain holes under the packing nut. After shutoff, the drain holes will allow water to

drain for a few moments to prevent freezing. This is normal and according to design.

Installation:

Installation procedures may vary slightly depending on the seat option purchased and the installation inlet options. The

C-634 wall hydrant is available with the following inlet options:

N1” MIP x 3/4” FIP

P1” Male SWT x 3/4” Female SWT

V3/4” ProPress Ready

Operation:

Operation of the C-634 Commercial Wall Hydrant is a simple process. Water ows through the hydrant after turning the

loose key one full turn counter-clockwise to the “on” position. The hydrant will achieve maximum ow at 2 1/2 full turns.

Turn off the hydrant by turning the loose key clockwise to the “off” position.

The hydrant will drain for a few moments. If the dripping persists after a few moments, tighten the key slightly until the

dripping stops. Be careful not to overtighten the hydrant.

The C-634 incorporates an integral atmospheric anti-siphon vacuum breaker that, in the rare occurrence of a back siphon-

age, opens to the atmosphere preventing contamination of the water supply.

As well as an atmospheric vacuum breaker, the C-634 incorporates vacuum breaker check valve in the rare case that

water is forced backwards into the valve.

*ALWAYS REMOVE HOSE DURING FREEZING TEMPERATURES*

*INTENDED FOR IRRIGATION USE AND OUTDOOR WATERING*

1. Determine the location for the installation of the hydrant. Ensure there is adequate

work room in the interior of the structure for securing the hydrant to the plumbing

piping. Bore a 1 1/8” diameter hole through the wall in the desired position for the

installation and a 1/4” hole that is 1/2” deep.

2. The PRIER C-634 is designed for installation in either the horizontal or vertical

position. If using vertical installation, it is recommended that the hydrant be installed

with the hose threads in the “up” position. Refer to the drawings below.

3. If you are planning to solder the connection, be certain the hydrant is in the fully

open position to prevent seat damage from the heat.

4. Connect the water supply piping to the hydrant as desired. With a closed-end hose

on the valve creating back pressure, test the installation for leakage.

5. After the water supply connection is made, secure the hydrant to the structure.

4515 East139thStreet

Grandview,MO64030

(800)362-9055

Fax (800)362-1463

INSTALLATION:

5.Flushallforeignparticles fromthewaterlinebefore

connectingtheFreezeless Hydrant.Foreignparticles

may clogthevacuumbreaker/backflowpreventorcaus-

ingittofail.

6. InserttheFreezeless Hydrant throughthepreviously

boredholeandsecurethehydranttotheinsideofthe

wallwiththeprovidedwallclampingring.

7.SecuretheFreezeless Hydranttothesupply piping.

Testtheinstallationforleakage.

1. De

termine thelocation forinstallationoftheFreeze-

less Hydrant.Besurethereis adequatework areaon

theinteriorofthestructureforsecuringtheFreezeless

Hydranttothewaterline.

3.Usingthe templateprovidedonthebox,borea1

3

/

8

”

diameterholethroughthewallinthedesiredposition,

anda

1

/

4

”hole thatis

1

/

2

”deep.

2. ThePrierC-634is designed forinstallationineither

horizontalorverticalposition.Ifusingverticalinstalla-

tion,itis recommendedthatthehydrantbein

stalledwith

thehosethreads inthe“up”position.Refertodrawings

totherightforcorrectinstallations.

4.IfplanningtosoldertheFreezeless Hydranttothe

supply piping, removetheoperatingstembeforeapply-

ingheattothevalve.Heatingthevalvewilldamagethe

sealingsurfaces onthestemoftheFreezeless Hydrant

OPERATION:

TheoperationofaPrierC-634Freezeless Wall

Hydrantis simple.TheFreezeless Hydrantwill

beginto flowatabout 1fullturnofthekey andwill

achievemaxi

mum flowat 2

1

/

2

fullturns.

Aftershutoff,thehydrantwilldrainwaterfrombe-

hindthepackingnut.Ifthewaterdrains formore

than1minute,thestoppermay needtobereplaced.

Donotoverturnwhenopeningorclosingthehydrant!

MAINTENANCE:

ThePrierC-634FreezelessWallHydrantrequiresno

scheduledmaintenanceforlongwearlife. Iftheop-

eratingstemisremoved,replacementof theO-Ring

onthewormsleeveandwormdriveisrecommended.

Recommended

Acceptable

NotRecommended

Acceptable

INSTALLATION, OPERATION& MAINTENANCE INSTRUCTIONSFOR

PRIERC-634HEAVY COMMERCIALWALL HYDRANTS

PARTS:

713

12

11

3

4

10

8

1

5

6

9

2

IDPartNo.Description

1

300-6003ValveStem Cap-Brass

2

300-6004Hose Piece-Brass

3

336-0001O-RingforWorm Sleeve Buna

4

336-6001O-RingforWorm DriveBuna

5

337-6001StopCheck-Acetal

6346-6001VB CheckWasher-Silicone

7

399-6001Stopper-Brass &EPDM

8

C-108KT-808OperatingKey onLanyard

9

C-634KT-806Vacuum Breaker CheckValveAssy

10

C-634KT-809WormDrive Assembly-Brass

11

C-634KT-808WormSleeve Assembly-Brass

12

C-634WCRW

all Clamp Ring-Iron

13

231-06CCStem for Close CoupledC-634

231-0604Stem for 4"C-634

231-0606Stem for 6"C-634

231-0608Stem for 8"C-634

231-0610Stem for 10" C-634

231-0612Stem for 12" C-634

231-0614Stem for 14" C-634

231-0618Stem for 18" C-634

231-0624Stem for 24" C-634

4515 East139thStreet

Grandview,MO64030

(800)362-9055

Fax (800)362-1463

INSTALLATION:

5.Flushallforeignparticles fromthewaterlinebefore

connectingtheFreezeless Hydrant.Foreignparticles

may clogthevacuumbreaker/backflowpreventorcaus-

ingittofail.

6. InserttheFreezeless Hydrant throughthepreviously

boredholeandsecurethehydranttotheinsideofthe

wallwiththeprovidedwallclampingring.

7.SecuretheFreezeless Hydranttothesupply piping.

Testtheinstallationforleakage.

1. De

termine thelocation forinstallationoftheFreeze-

less Hydrant.Besurethereis adequatework areaon

theinteriorofthestructureforsecuringtheFreezeless

Hydranttothewaterline.

3.Usingthe templateprovidedonthebox,borea1

3

/

8

”

diameterholethroughthewallinthedesiredposition,

anda

1

/

4

”hole thatis

1

/

2

”deep.

2. ThePrierC-634is designed forinstallationineither

horizontalorverticalposition.Ifusingverticalinstalla-

tion,itis recommendedthatthehydrantbein

stalledwith

thehosethreads inthe“up”position.Refertodrawings

totherightforcorrectinstallations.

4.IfplanningtosoldertheFreezeless Hydranttothe

supply piping, removetheoperatingstembeforeapply-

ingheattothevalve.Heatingthevalvewilldamagethe

sealingsurfaces onthestemoftheFreezeless Hydrant

OPERATION:

TheoperationofaPrierC-634Freezeless Wall

Hydrantis simple.TheFreezeless Hydrantwill

beginto flowatabout 1fullturnofthekey andwill

achievemaxi

mum flowat 2

1

/

2

fullturns.

Aftershutoff,thehydrantwilldrainwaterfrombe-

hindthepackingnut.Ifthewaterdrains formore

than1minute,thestoppermay needtobereplaced.

Donotoverturnwhenopeningorclosingthehydrant!

MAINTENANCE:

ThePrierC-634FreezelessWallHydrantrequiresno

scheduledmaintenanceforlongwearlife. Iftheop-

eratingstemisremoved,replacementof theO-Ring

onthewormsleeveandwormdriveisrecommended.

Recommended

Acceptable

NotRecommended

Acceptable

INSTALLATION, OPERATION& MAINTENANCE INSTRUCTIONSFOR

PRIERC-634HEAVY COMMERCIALWALL HYDRANTS

PARTS:

713

12

11

3

4

10

8

1

5

6

9

2

IDPartNo.Description

1

300-6003ValveStem Cap-Brass

2

300-6004Hose Piece-Brass

3

336-0001O-RingforWorm Sleeve Buna

4

336-6001O-RingforWorm DriveBuna

5

337-6001StopCheck-Acetal

6346-6001VB CheckWasher-Silicone

7

399-6001Stopper-Brass &EPDM

8

C-108KT-808OperatingKey onLanyard

9

C-634KT-806Vacuum Breaker CheckValveAssy

10

C-634KT-809WormDrive Assembly-Brass

11

C-634KT-808WormSleeve Assembly-Brass

12

C-634WCRW

all Clamp Ring-Iron

13

231-06CCStem for Close CoupledC-634

231-0604Stem for 4"C-634

231-0606Stem for 6"C-634

231-0608Stem for 8"C-634

231-0610Stem for 10" C-634

231-0612Stem for 12" C-634

231-0614Stem for 14" C-634

231-0618Stem for 18" C-634

231-0624Stem for 24" C-634

4515 East139thStreet

Grandview,MO64030

(800)362-9055

Fax (800)362-1463

INSTALLATION:

5.Flushallforeignparticles fromthewaterlinebefore

connectingtheFreezeless Hydrant.Foreignparticles

may clogthevacuumbreaker/backflowpreventorcaus-

ingittofail.

6. InserttheFreezeless Hydrant throughthepreviously

boredholeandsecurethehydranttotheinsideofthe

wallwiththeprovidedwallclampingring.

7.SecuretheFreezeless Hydranttothesupply piping.

Testtheinstallationforleakage.

1. De

termine thelocation forinstallationoftheFreeze-

less Hydrant.Besurethereis adequatework areaon

theinteriorofthestructureforsecuringtheFreezeless

Hydranttothewaterline.

3.Usingthe templateprovidedonthebox,borea1

3

/

8

”

diameterholethroughthewallinthedesiredposition,

anda

1

/

4

”hole thatis

1

/

2

”deep.

2. ThePrierC-634is designed forinstallationineither

horizontalorverticalposition.Ifusingverticalinstalla-

tion,itis recommendedthatthehydrantbein

stalledwith

thehosethreads inthe“up”position.Refertodrawings

totherightforcorrectinstallations.

4.IfplanningtosoldertheFreezeless Hydranttothe

supply piping, removetheoperatingstembeforeapply-

ingheattothevalve.Heatingthevalvewilldamagethe

sealingsurfaces onthestemoftheFreezeless Hydrant

OPERATION:

TheoperationofaPrierC-634Freezeless Wall

Hydrantis simple.TheFreezeless Hydrantwill

beginto flowatabout 1fullturnofthekey andwill

achievemaxi

mum flowat 2

1

/

2

fullturns.

Aftershutoff,thehydrantwilldrainwaterfrombe-

hindthepackingnut.Ifthewaterdrains formore

than1minute,thestoppermay needtobereplaced.

Donotoverturnwhenopeningorclosingthehydrant!

MAINTENANCE:

ThePrierC-634FreezelessWallHydrantrequiresno

scheduledmaintenanceforlongwearlife. Iftheop-

eratingstemisremoved,replacementof theO-Ring

onthewormsleeveandwormdriveisrecommended.

Recommended

Acceptable

NotRecommended

Acceptable

INSTALLATION, OPERATION& MAINTENANCE INSTRUCTIONSFOR

PRIERC-634HEAVY COMMERCIALWALL HYDRANTS

PARTS:

713

12

11

3

4

10

8

1

5

6

9

2

IDPartNo.Description

1

300-6003ValveStem Cap-Brass

2

300-6004Hose Piece-Brass

3

336-0001O-RingforWorm Sleeve Buna

4

336-6001O-RingforWorm DriveBuna

5

337-6001StopCheck-Acetal

6346-6001VB CheckWasher-Silicone

7

399-6001Stopper-Brass &EPDM

8

C-108KT-808OperatingKey onLanyard

9

C-634KT-806Vacuum Breaker CheckValveAssy

10

C-634KT-809WormDrive Assembly-Brass

11

C-634KT-808WormSleeve Assembly-Brass

12

C-634WCRW

all Clamp Ring-Iron

13

231-06CCStem for Close CoupledC-634

231-0604Stem for 4"C-634

231-0606Stem for 6"C-634

231-0608Stem for 8"C-634

231-0610Stem for 10" C-634

231-0612Stem for 12" C-634

231-0614Stem for 14" C-634

231-0618Stem for 18" C-634

231-0624Stem for 24" C-634

4515 East139thStreet

Grandview,MO64030

(800)362-9055

Fax (800)362-1463

INSTALLATION:

5.Flushallforeignparticles fromthewaterlinebefore

connectingtheFreezeless Hydrant.Foreignparticles

may clogthevacuumbreaker/backflowpreventorcaus-

ingittofail.

6. InserttheFreezeless Hydrant throughthepreviously

boredholeandsecurethehydranttotheinsideofthe

wallwiththeprovidedwallclampingring.

7.SecuretheFreezeless Hydranttothesupply piping.

Testtheinstallationforleakage.

1. De

termine thelocation forinstallationoftheFreeze-

less Hydrant.Besurethereis adequatework areaon

theinteriorofthestructureforsecuringtheFreezeless

Hydranttothewaterline.

3.Usingthe templateprovidedonthebox,borea1

3

/

8

”

diameterholethroughthewallinthedesiredposition,

anda

1

/

4

”hole thatis

1

/

2

”deep.

2. ThePrierC-634is designed forinstallationineither

horizontalorverticalposition.Ifusingverticalinstalla-

tion,itis recommendedthatthehydrantbein

stalledwith

thehosethreads inthe“up”position.Refertodrawings

totherightforcorrectinstallations.

4.IfplanningtosoldertheFreezeless Hydranttothe

supply piping, removetheoperatingstembeforeapply-

ingheattothevalve.Heatingthevalvewilldamagethe

sealingsurfaces onthestemoftheFreezeless Hydrant

OPERATION:

TheoperationofaPrierC-634Freezeless Wall

Hydrantis simple.TheFreezeless Hydrantwill

beginto flowatabout 1fullturnofthekey andwill

achievemaxi

mum flowat 2

1

/

2

fullturns.

Aftershutoff,thehydrantwilldrainwaterfrombe-

hindthepackingnut.Ifthewaterdrains formore

than1minute,thestoppermay needtobereplaced.

Donotoverturnwhenopeningorclosingthehydrant!

MAINTENANCE:

ThePrierC-634FreezelessWallHydrantrequiresno

scheduledmaintenanceforlongwearlife. Iftheop-

eratingstemisremoved,replacementof theO-Ring

onthewormsleeveandwormdriveisrecommended.

Recommended

Acceptable

Not Recommended

Acceptable

INSTALLATION, OPERATION& MAINTENANCE INSTRUCTIONSFOR

PRIERC-634HEAVY COMMERCIALWALL HYDRANTS

PARTS:

713

12

11

3

4

10

8

1

5

6

9

2

IDPartNo.Description

1

300-6003ValveStem Cap-Brass

2

300-6004Hose Piece-Brass

3

336-0001O-RingforWorm Sleeve Buna

4

336-6001O-RingforWorm DriveBuna

5

337-6001StopCheck-Acetal

6346-6001VB CheckWasher-Silicone

7

399-6001Stopper-Brass &EPDM

8

C-108KT-808OperatingKey onLanyard

9

C-634KT-806Vacuum Breaker CheckValveAssy

10

C-634KT-809WormDrive Assembly-Brass

11

C-634KT-808WormSleeve Assembly-Brass

12

C-634WCRW

all Clamp Ring-Iron

13

231-06CCStem for Close CoupledC-634

231-0604Stem for 4"C-634

231-0606Stem for 6"C-634

231-0608Stem for 8"C-634

231-0610Stem for 10" C-634

231-0612Stem for 12" C-634

231-0614Stem for 14" C-634

231-0618Stem for 18" C-634

231-0624Stem for 24" C-634

Maintenance:

The C-634 Heavy Commercial Wall Hydrant leaves the factory fully air tested and operational. It is treated with an FDA

approved lubrication. The hydrant requires no scheduled maintenance to provide long life. If the stem is removed, the

bypass O-Ring needs to be replaced and lubricated with an FDA approved lubricant to avoid tearing.

*P and V inlets only available with CC length