Phanteks Eclipse G360A Handleiding

Phanteks Computerbehuizing Eclipse G360A

Bekijk gratis de handleiding van Phanteks Eclipse G360A (2 pagina’s), behorend tot de categorie Computerbehuizing. Deze gids werd als nuttig beoordeeld door 5 mensen en kreeg gemiddeld 4.2 sterren uit 3 reviews. Heb je een vraag over Phanteks Eclipse G360A of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Download PDF

Pagina 1/2

INSTALLATION GUIDE

INSTRUCTIONS

Thank you for choosing Phanteks. Please take a moment to

carefully go through the manual. This manual will walk you

through all of the features the Eclipse G360A has to offer and

installation steps to build a full system.

This manual is intended for:

Eclipse G360A

Phanteks will not take responsibility for any damages incurred due to incorrect

installation or usage of this product.

VERSION 1.1

| www.phanteks.com

USB 3.0

AUDIO/MIC

MODE BUTTON

COLOR BUTTON

POWER BUTTON

INSTALLATION GUIDE

| www.phanteks.com

SSD + MOTHERBOARD

SCREW

22x

MOTHERBOARD

STAND-OFF

PSU SCREW

D-RGB 120MM FAN

3x pre-installed

2.5” SSD BRACKET

2x pre-installed

ZIP TIE

280 140 FRONT AIO COOLER 4X MM FANS TOP & FRONT

360 360 FRONT AIO COOLER TOP AIO COOLER

The Eclipse G360A chassis allows for multiple different cooling

configuration. These are four examples to maximize the G360A’s

cooling potential.

FRONT TOP REAR

CLEARANCE

FANS

RADIATOR

120mm

up to 360

* *

up to 360

up to 120

up to 280

140mm

CPU cooler height

RAM height

GPU length

Power Supply

E-ATX

Front 360 radiator

Front 280 radiator

Top 360 Radiator

162 mm

42 mm when using top radiator

400 mm

220 / 280 mm

280 mm width

122x398x65 mm

142x330 mm

122x398 mm

AIO 360

AIO 280

VERTICAL GPU BRACKET (PH-VGPUKT4.0_03)

The . G360A chassis supports the Phanteks Vertical GPU Bracket

The Vertical GPU Bracket supports 3 and 4 slot GPU’s with access

to the GPU connectors on slot 1 and 2.

It can be easily installed in the PCI slot area. Follow the instructions

that are included with the Vertical GPU bracket.

OPTIONAL UPGRADE

MODES COLORS

Press and hold the button for two seconds to turn MODE

off LEDs, press again to turn it ON

NOTE | D-RGB control buttons are deactivated if connected to a motherboard.

SOLID

BREATHING

SPARKLE

MUTLI-COLOR

TURN OFF LEDs

Fans can be placed on the front of the chassis behind the front panel.

Maximum number of 140 mm fans

RAM Height Clearance | 42 mm

140MM

120MM

120MM120MM

120MM 120MM

140MM

HDD LOCKING SCREW

FAN & RADIATOR SUPPORT D-RGB CONTROLS

INCLUDED ACCESSORIES

RECOMMENDED COOLING CONFIGURATION

FRONT I/O

PRO TIP

For a more vibrant D-RGB light

effect, place the fans directly

under the front panel

It is not possible to install a 360 radiator in the front and top simultaneously

INSTALLATION GUIDE INSTALLATION GUIDE

0302

PANEL REMOVAL

HARDWARE INSTALLATION

LEFT SIDE PANEL

MOTHERBOARD POWERSUPPLY

STORAGE 2.5” SSD|

STORAGE 3.5” HDD|

RIGHT SIDE PANEL

FRONT PANEL & DUST FILTERS FRONT FAN BRACKETS

Before starting the installation process, we recommend to

remove all external panels. Follow these steps below.

Loosen the 2 captive thumb screws and slide to remove the

tempered glass side panel.

Remove front panel by pulling the panel from below.

Install the ATX motherboard using 9x motherboard screws. For

M-ATX Motherboards follow the motherboard instructions to

move the stand-offs to the correct position.

Install the power supply with 4x PSU screws.

Remove the front brackets for

easier installation of the front fans

or radiator.

For 140 mm fans

remove only the

left bracket.

Loosen the 2 captive thumb screws and slide to remove the right

side panel.

Slide the SSD Bracket up to remove it from the chassis.

Slide the 3.5” HDD trays out of the HDD cage.

To move the HDD Bracket to a different position, (or remove)

remove 8x screws located at the bottom and the PSU cover.

The HDD cage has 2 possible positions to allow for a front 360

radiator or for additional PSU clearance

Open the side clips, place the HDD and close the clips to secure

the HDD in place.

Secure the SSD with 4x SSD screws to the SSD Bracket.

| www.phanteks.com | www.phanteks.com

PRO TIP

The HDD tray can also hold

a 2.5” SSD

CABLES

Connect the front I/O cables to the motherboard and power

supply.

More D-RGB lighting products can be connected to the integrated

D-RGB controller. Optionally, lighting can be connected and

controlled via motherboard software.

Motherboard header

MOTHERBOARD FRONT I/O

EXPAND WITH MORE D-RGB PRODUCTS SYNC LIGHTING TO THE MOTHERBOARD

SK D-RGB FAN 120MM

TOP FILTER

PSU FILTER

120MM FANS 140MM FANS

SLIDE UP TO

REMOVE

SLIDE DOWN TO

INSTALL

THUMBSCREW

LOOSEN

2x THUMBSCREW

LOOSEN

CASE SCREW

REMOVE

CASE SCREW

REMOVE

MOTHERBOARD

SCREWS

INSTALL

PSU SCREW

INSTALL

PSU

SSD SCREW

INSTALL

65mm

220mm

INSTALLATION GUIDE

VERSION 1.1

280mm

Product specificaties

Merk:	Phanteks
Categorie:	Computerbehuizing
Model:	Eclipse G360A
Kleur van het product:	Wit
Gewicht:	6510 g
Breedte:	455 mm
Diepte:	200 mm
Hoogte:	465 mm
Gewicht verpakking:	7840 g
Breedte verpakking:	513 mm
Diepte verpakking:	282 mm
Hoogte verpakking:	537 mm
Soort:	PC
Vormfactor:	Midi Tower
Aan-/uitknop:	Ja
Verlichtingslocatie:	Voorkant
Materiaal:	Staal
Aantal poorten USB 3.2 Gen 1 (3.1 Gen 1) Type A:	2
Kleur van de verlichting:	Multi
Combo koptelefoon/microfoon port:	Ja
Vermogenstoevoer inclusief:	Nee
Aantal 2.5" bays:	3
Aantal 3.5" bays:	2
Ondersteunde HDD-groottes:	2.5, 3.5 "
Aantal uitbreidingssleuven:	7
Verbeterd kabelbeheer:	Ja
Belichting:	Ja
Supported motherboard form factors:	ATX, EATX, Micro ATX, Mini-ITX
Zijraam:	Ja
Geharde glaspla(a)t(en):	Ja
Maximum CPU cooler hoogte:	162 mm
Maximum grafische kaart lengte:	400 mm
Maximum PSU lengte:	280 mm
Maximale aantal ventilators voorkant:	3
Voorste ventilators ondersteunende diameters:	120,140 mm
Maximaal aantal ventilators bovenkant:	3
Bovenste ventilators ondersteunende diameters:	120,140 mm
Maximaal aantal ventilators achterkant:	1
Achterkant ventilators ondersteunende diameters:	120 mm
Aantal geïntstalleerde ventilators voorkant:	3x 120 mm
Garantieperiode:	5 jaar
RGB-regelknop:	Ja
Ondersteunde afmetingen voorste radiator:	280,360 mm
Ondersteunde afmetingen achterste radiator:	120 mm
Ondersteunde afmetingen bovenste radiator:	360 mm