Peavey SP 118 Handleiding

Peavey Speaker SP 118

Lees hieronder de 📖 handleiding in het Nederlandse voor Peavey SP 118 (4 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 18 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4

www.peavey.com

SP®118

Product

Specications

ENGLISH

SP®118 Sub

e SP® 118 features the Peavey exclusive 1808-8 AL CP Pro Rider®. Designed to support and enhance the bass output of the

full-range SP series sound reinforcement enclosures, it transforms a system into a thumping beast.

e SP® 118 enclosure is constructed of plywood augmented with internal braces, coated in a black textured polyurethane nish. A

full-length, wrap-around perforated steel grille protects the front of the enclosure. A pole mount plate is located on the top of the

enclosure, with an insert for a threaded pole, using M20 threads. Multiple y points are provided to allow overhead rigging.

Input connection to the system is made on the rear of the system, via an input cup with two 1/4” phone jacks and one four-pin twist

lock connector in parallel.

As the SP® 118 does not include a passive subwoofer crossover, input should be electronically ltered of typical subwoofer applications.

In addition for high power operation, a high pass lter set to 40 Hz or higher and of 24 dB/octave slope should be used to improve

performance and reliability.

FEATURES:

• 18” 1808-8 AL CP Pro Rider® woofer

• 1200 watts program, 2400 watts peak

• Inputs include one four-pin twist lock connector and two 1/4” phone jacks

• Pole mount plate built-in, threaded for positive pole support

* Threaded pole for mount included.

* Multiple Fly Points

Flying/Rigging Information

Caution: Before attempting to suspend this speaker, consult a certified structural engineer. Speaker can fall from improper

suspension, resulting in serious injury and property damage. Do not suspend or mount any other product or device from

this enclosure! Maximum enclosure angle 30 degrees. Use only the correct mating hardware. All associated rigging is the

responsibility of others.

Hardware for Flying/Rigging the SP®-118

Eyebolts or bracket bolts should be M8 metric thread.

Eyebolts and bracket bolts must conform to certain minimum strength criteria for safety reasons.

Unspecified eyebolts found at local hardware stores are not strong enough to maintain safety for overhead flying or rigging. Use only

forged steel shoulder machinery eyebolts designed for rigging use, which adhere to the stated standards as outlined below.

Hardware Specifications

Forged shoulder machinery eyebolts should be an M8 size, 1.25 mm per thread, and must conform to DIN 580 or ASTM A489, for

Germany, BGV-C1 is the relevant standard. Minimum shank length should be 26 mm. The eyebolts should be rated for a minimum

of 1,000 lbs straight pull working load

Bolts used on custom mounting brackets must be certified to be a metric grade 8.8 or better.

If there are any questions regarding the proper hardware or practices for safe flying or rigging of the Peavey SP® 118, contact a certified

structural engineer, or consult with those local rigging companies who have trained and certified personnel.

Architectural & Engineering Specifications

The loudspeaker system shall have an operating bandwidth of 51 Hz to 320 Hz. The nominal output level shall be 98 dB

when measured at a distance of 1 meter with an input of 1 watt. The nominal impedance shall be 8.0 ohms. The maximum continuous

power handling shall be 600 watts, with maximum program power of 1,200 watts, peak power input of at least 2,400 watts and a

minimum amplifier headroom of 3 dB. It shall use a Peavey 1808-8 AL CP Pro Rider® woofer. Fly point inserts shall be provided, 12

per cabinet, at the following locations: 3 top, 3 bottom and 2 each side & 1 each top rear and bottom rear. The outside dimensions

shall be 26.38 inches high by 22.84 inches wide by 24.5 inches deep. The weight shall be 77 lbs. The loudspeaker system shall be a

Peavey model SP® 118.

Frequency Response, 1 meter on-axis, swept-sine in anechoic environment:

51 Hz to 320 Hz (±3 dB)

Usable Low Frequency limit (-10 dB point):

41 Hz

Power Handling:

Low Frequency Section:

600 W continuous

1,200 W program

2,400 W peak

Sound Pressure Level, 1 Watt, 1 meter in anechoic environment:

Low Frequency Section:

98 dB SPL, (2.83 V input)

Maximum Sound Pressure Level (1 meter):

Low Frequency Section:

126 dB SPL continuous

132 dB SPL peak

Transducer Complement:

Low Frequency Section:

1 X 18” woofer, vented

1808-8 AL CP Pro Rider®

Box Tuning Frequency:

Low Frequency Section: 43 Hz

Product specificaties

Merk:	Peavey
Categorie:	Speaker
Model:	SP 118

Heb je hulp nodig?

Als je hulp nodig hebt met Peavey SP 118 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Speaker Peavey

Peavey S-12825 RB Handleiding

12 Maart 2024

Peavey SSE 10 Handleiding

27 Juli 2023

Peavey RBN 118 Handleiding

22 Juni 2023

Peavey PHR 860S Handleiding

15 Juni 2023

Peavey ISM 5Tx Handleiding

1 Juni 2023

Peavey PV 115D Handleiding

31 Mei 2023

Peavey RBN 110 Handleiding

21 Mei 2023

Peavey RX 22N Handleiding

18 Mei 2023

Peavey SP 4P Handleiding

10 Mei 2023

Peavey PVXp 12 Bluetooth Handleiding

8 Mei 2023

Handleiding Speaker

Nieuwste handleidingen voor Speaker

OTTO Bluetooth Revo NC2 Handleiding

20 April 2024

REL Acoustics Strata Handleiding

20 April 2024

REL Acoustics Strata III Handleiding

20 April 2024

Soen Transit Handleiding

18 April 2024

Miller & Kreisel MP300RC Handleiding

18 April 2024

Soen Transit XS Handleiding

18 April 2024

Miller & Kreisel MP7 Handleiding

18 April 2024

Qian QRBT1801 Handleiding

17 April 2024

Focal Twin6 Handleiding

17 April 2024

Kenwood KFC-WPS1000F Handleiding

16 April 2024