Panamax MR5100 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Panamax MR5100 (3 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 6 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/3
Specifications subject to change due to product upgrades and improvements.
*Go to www.panamax.com for detailed noise filtering information.
Español - Para la versión en español de este documento, vaya a www.panamax.com/products
Français - Pour la version espagnole de ce document, allez à www.panamax.com/products
DIN-00017 - REV. D
OUTLET BANKS 1, 2 and 3
INDICATOR LEDS
POWER ON / OFF
ON / OFF, CONTROL FOR
DECORATIVE BLUE LIGHTS AND VOLTMETER
(Voltmeter and blue lights can be illuminated when power is off)
SAFE POWER AND
VOLTAGE INDICATOR
UNSAFE VOLTAGE
INDICATOR
LINE FAULT
INDICATOR
FRONT PANEL
CONVENIENCE OUTLET
(SWITCHED)
USB CHARGER
5VDC, 500mA
10 ft. POWER
CORD,
NEMA 5-15
GROUND LUG
15 AMP CIRCUIT
BREKAER
RESETTABLE
OUTLET BANK 3
(DELAYED CURRENT)
OUTLET BANK 2
(SWITCHED)
OUTLET BANK 1
(ALWAYS ON)
LAN SURGE
PROTECTION
1 PAIR OF
RJ-45 IN/OUT
CONNECTORS
COAXIAL SURGE
PROTECTION
2 PAIRS
UNIVERSAL
IN/OUT
CONNECTORS
TELCO SURGE PROTECTION
1 PAIR OF RJ-11 IN/OUT CONNECTORS
Note to CATV Installers:
This reminder is provided to call attention to Article 820-40 of the NEC. That article provides
specific guidelines for proper grounding.It specifies that the cable ground shall be connected
to the grounding system of the building and as close to the point of entry as practical.
Front Panel Features
MR5100 Features and Specifications
Panamax LLC, 1800 South McDowell Blvd., Petaluma, CA 94954 • 707-283-5900 • 800-472-5555 • www.panamax.com
©2012 Panamax LLC, Panamax Logo is a US registered trademark of Core Brands, LLC.
Model MR5100 Reference Guide
AC PROTECTION
Protect or Disconnect Circuitry_________________________________________________Yes
Patented Power Management Circuit____________________________________________Yes
Overvoltage Shutoff____________________________________________________ 140V ±3V
Undervoltage Shutoff___________________________________________________ 100V ±1V
Thermal Fusing___________________________________________________________Yes
Line Voltage___________________________________________________120VAC, 50/60HZ
Initial Clamping Level__________________________________________ 200V Peak, 141VRMS
Voltage Protection Rating (UL 1449 3rd Edition, 3,000A)____________________________400V
Protection Modes_________________________________________________ L-N, L-G, N-G
Maximum Current Rating_____________________________________________15A (1800W)
EMI/RFI Noise Filtration______________________________ Panamax Level 3 Noise Filtration*
Response Time__________________________________________________________< 1ns
Single Pulse Energy Dissipation_________________________________________2025 Joules
Peak Impulse Current___________________________________________________52,000 A
LAN PROTECTION
Clamping Level____________________________________________________ 62±6V @ 1 mA
Compatibility___________________________________________________10/100/1000bT
Wires Protected _______________________________________________________8-Wires
Connectors____________________________________________________________RJ-45
TEL PROTECTION
Fuseless/Auto-Resetting________________________________________________Yes
Clamping Level__________________________________________________________260V
Wires Protected _________________________________________________ 2 wire, 1 pair (4, 5)
Connectors_________________________________________________________RJ-11
UNIVERSAL COAX PROTECTION
HD 1080 i/p Ready_________________________________________________________Yes
Bidirectional__________________________________________________________Yes
Shielded____________________________________________________________Yes
Clamping Level___________________________________________________________75V
Frequency Range_________________________________________________OMHz - 2.2 GHz
Insertion Loss_________________________________________________________ <0.5 dB
Connections______________________________________________ Female “F”, Gold Plated
Key Features
Exclusive Automatic Voltage Monitoring (AVM)
Panamax’s patent pending power monitoring
circuitry constantly monitors the AC line voltage
for unsafe voltage conditions such as momentary
spikes, prolonged over-voltages and under-volt-
ages (brownouts). These unsafe conditions pose
a very dangerous threat to all electronic equip-
ment within the home. If the MR5100 senses
an unsafe power condition, it will automatically
disconnect power from your equipment to pro-
tect equipment from damage. The front panel
indicator will also alert users to the power condi-
tion. Once the voltage returns to a safe level, the
MR5100 will automatically reconnect the power
to the outlets.
Protect or Disconnect™ Technologies
In the event of a catastrophic surge such as light-
ning, it completely disconnects AC power to con-
nected equipment.
Front Panel Outlet
MR5100 features a protected and noise ltered
convenience outlet located on the front panel.
Perfect for temporary gaming systems, por-
table electronics (such as music players or smart
phones), or other personal electronics.
Front Panel Decorative Lights
Blue decorative lights add an attractive look at feel
to your equipment rack or TV cabinet.
Antenna, Cable, Sat and LAN Signal protection
Coaxial protection circuits prevent damaging
surges from entering through signal paths and
have the smallest signal loss on the market - less
than 0.5 db of attenuation from 0Hz to 2.2GHz.
Our coaxial protection has been specifically
designed to virtually eliminate signal loss. The
clamping level of 75V will meet and exceed the
demands of both cable and satellite voltages
while minimizing exposure to damaging spikes
and surges. LAN protection allows for 10/100
base-T Ethernet equipment to integrate into an
audio/video system without the risk of upstream
surge damage from a gateway, switch, router or
other network device.
Eleven Protected and Filtered Power Outlets
(see specifications)
Ten Foot Power Cable with Straight Plug
NEMA 5-15P, fixed starin relief, unshielded,
straight plug.
TO GET STARTED
1. With MR5100 disconnected from the wall outlet, plug the equipment to be protected into the MR5100
AC outlets.
2. Connect any LAN, TELEPHONE and COAX lines to be protected to the appropriate connectors on the
MR5100.
3. Plug the MR5100 into the wall outlet and verify that the LINE FAULT INDICATOR LED is NOT lit, indicat
-
ing that the wall outlet is properly wired and grounded. If it is LIT, call a licensed electrician to inspect and
implement proper and safe wiring.
4. Turn on MR5100 by pressing the POWER ON button and proceed to turn on your connected equipment.
IMPORTANT SAFETY POINTS
Panamax surge protectors and the connected equipment must be indoors, in a dry location and in the same
building. Although your Panamax protector is very durable, its internal components are not isolated from the
environment. Do not install any Panamax product near heat emitting appliances such as a radiator or heat register.
Do not install this product where excessive moisture is present; for example near a bath tub, sink, pool basement
floor, fish tank, etc. It is not uncommon for a building to be improperly grounded. In order to protect your equipment,
Panamax products must be plugged into a properly wired and grounded 3-wire outlet. Additionally, building wiring
and grounding must conform to applicable NEC (USA) or CEC (Canada) codes for the Panamax protection policy to
be valid. Do not use 2-blade adapters or any other “power strips” with this product. Use only Panamax extension
cord, or a UL / CSA recognized power cord.
Back Panel Features
BANK 1 ON
INDICATOR LIGHT
BANK 1 BANK 2 BANK 3
MR5100
CATV / SAT 1
UNIVERSAL COAX PROT ECT IO N
CATV / SAT 2
TEL
OUT
IN
OUT
LAN
OUT
TEL
IN
LAN
IN
IN
OUT
BANK 3
HIGH CURRENT
DELAYED
OUT LET S
BANK 1
FILTERED / LIFT
ALWAYS ON
OUT LET S
BANK 2
FILTERED / LIFT
SWITCHED OUT LET S BANK 1 ON
GROUND
LUG
15 AMP
CIRCUIT
BREAKER
MAIN POWER 120 VAC/15A
LAN PROTECTION
TEL PROT ECT IO N
MR5100 Limited Product Warranty and Connected Equipment Policy Information
CAUTION!
All Panamax Warranties and Connected Equipment Policies are valid only in the United States and Canada.
CAUTION!
Audio/Video, computer and/or telephone system installations can be very complex systems, consisting of many interconnected components.
Due to the nature of electricity and surges, a single protector may not be able to completely protect complex installations. In those cases, a systematic approach using multiple protectors must be
employed. Systematic protection requires professional design. AC power, satellite cables, CATV cables, telephone/network lines, signal lines or any other electrical conductors, entering the system
that do not pass through this surge protector may invalidate the Panamax Connected Equipment Protection Policy. For additional information on how to protect your system, please contact Panamax
before connecting your equipment to the surge protector.
CAUTION!
WARRANTY LIMITATION FOR INTERNET PURCHASERS
Panamax products purchased through the Internet do not carry a valid Product Warranty or Connected Equipment Protection Policy unless purchased from an Authorized Panamax Internet Dealer
and the original factory serial numbers are intact (they must not have been removed, defaced or replaced in any way). Purchasing from an Authorized Panamax Internet Dealer insures that the product
was intended for consumer use, has passed all quality inspections and is safe. Buying through auction sites or unauthorized dealers may result in the purchase of salvaged, failed and/or products not
intended for use in the US. In addition, Authorized Panamax Internet dealers have demonstrated sufficient expertise to insure warranty compliant installations. For a list of Authorized Panamax Internet
Dealers go to www.panamax.com. If you have any questions regarding these requirements, please contact Panamax Customer Relations.
Product Upgrade Program
If your Panamax power conditioner sacrifices it-
self while protecting your connected equipment,
you have an option to upgrade to the latest tech-
nology. Please go to our web site www.panamax.
com or contact Panamax Customer Relations at
800-472-5555 for details.
Panamax Power
Conditioner Limited
Product Warranty
Panamax warrants to the purchaser of this Pan-
amax audio/video component style power condi-
tioner, for a period of three (3) years from the
date of purchase, that the unit shall be free of
defects in design, material or workmanship, and
Panamax will repair or replace any defective unit.
For product replacement see “NOTIFICATION”
section (3).
Panamax Power Conditioner
Limited Connected Equipment
Protection Policy
It is the policy of Panamax that it will, at its elec-
tion, either replace, pay to replace at fair market
value, or pay to repair, up to the dollar amount
specified below, equipment that is damaged by
an AC power, cable, telephone, or lightning surge
while connected to a properly installed Panamax
power conditioner. To be eligible for compensa-
tion, repair and or replacement, the power condi-
tioner must shows signs of surge damage or that
it is operating outside of design specifications,
relative to its surge protection capability, and un-
der all of the circumstances failed to protect your
connected equipment.
MR5100: $5,000,000
THE CONNECTED EQUIPMENT POLICY IS
SUBJECT TO THE FOLLOWING CONDITIONS
AND LIMITATIONS
1. ORIGINAL OWNERSHIP REQUIREMENT:
Panamax’s connected equipment policy extends
to the original purchaser of the Panamax product
only and is non-transferable. Original purchase
receipts must accompany any product return or
claim for connected equipment damage.
2. PROPER INSTALLATION: Panamax AC protec-
tors must be directly plugged into a properly
grounded 3-wire AC outlet. Extension cords*,
non-grounded two prong adapters, or other
non-Panamax surge products must not be used.
Building wiring and other connections to protect-
ed equipment must conform to applicable codes
(NEC or CEC). No other ground wires or ground
connections may be used. All wires (including,
e.g., AC power lines, telephone lines, signal/
data lines, coaxial cable, antenna lead-ins) lead-
ing into the protected equipment must first pass
through a single Panamax protector designed for
the particular application. The protector and the
equipment to be protected must be indoors in a
dry location, and in the same building. Panamax
installation instructions and diagrams must be
followed
3. NOTIFICATION: You must notify Panamax with-
in ten days of any event precipitating request for
product replacement or payment for connected
equipment damage. A return authorization (RA)
number must first be obtained from the Pan-
amax Customer Relations Department at www.
panamax.com** before returning the protector
Panamax. At this time, you must notify Panamax
if you believe you have a claim for damaged con-
nected equipment. Once you obtain an RA num-
ber, please mark the number on the bottom of
the unit and pack it in a shipping carton/box with
enough packing material to protect it during tran-
sit. The RA number must also be clearly marked
on the outside of the carton. Ship the unit Pan-
amax. Please note that you are responsible for
any and all charges related to shipping the unit to
Panamax. If connected equipment damage was
indicated on your RA request, Panamax will mail
you claim kit to be completed and returned within
30 days. A connection diagram of your system
will be required as part of the claim kit. Be sure to
note its configuration before disconnecting your
equipment.
4. DETERMINATION OF FAILURE: Panamax will
evaluate the protector for surge damage. The
Panamax protector must show signs of surge
damage or must be performing outside (>10%)
of design specifications relative to its surge
protection capability. Opening the enclosure,
tampering with, or modifying the unit in any way
shall be grounds for an automatic denial your
request for payment. Panamax, after evaluating
all information provided, will determine whether
or not your request is eligible for payment. If the
surge protector shows no signs of AC power or
signal line surge damage and is working within
design specifications, Panamax will return the
unit to you with a letter explaining the test results
Exceptions: If a dealer or installer replaces the
protector for the customer, replacement will be
returned to the dealer installer; or if the protec-
tor is a pre-1996 model, it will be replaced; or,
for a Canadian customer, the protector will be
replaced. Panamax reserves the right to inspect
the damaged connected equipment, parts, or cir-
cuit boards. Please note that you are responsible
for any and all charges related to shipping the
damaged equipment to Panamax. Panamax also
reserves the right to inspect the customer’s facil-
ity. Damaged equipment deemed uneconomical
to repair must remain available for inspection by
Panamax until the claim is finalized.
5. REQUEST PAYMENTS: Once Panamax has de-
termined that you are entitled to compensation,
Panamax will, at its election, either pay you the
present fair market value of the damaged equip-
ment, or pay for the cost of the repair, or send
you replacement equipment, or pay the equiva-
lence of replacement equipment.
6. OTHER INSURANCE/WARRANTIES: This cover-
age is secondary to any existing manufacturer’s
warranty, implied or expressed, or any insurance
and/or service contract that may cover the loss.
7. EXCLUSIONS: THE PANAMAX CONNECTED
EQUIPMENT PROTECTION POLICY DOES NOT AP-
PLY TO: Service charges, installation costs, rein-
stallation costs; setup cost; diagnostic charges;
periodic checkups; routine maintenance; loss of
use of the product; costs or expenses arising out
of reprogramming or loss of programming and/
or data; shipping charges or fees; service calls;
loss or damage occasioned by re, theft, flood,
wind, accident, abuse or misuse, and products
subject to manufacturers recall or similar event.
8. DISPUTE RESOLUTION: Any controversy or
claim arising out of or relating to Panamax’s
Connected Equipment Protection Policy, or the
alleged breach thereof, shall be settled by arbitra-
tion administered by the American Arbitration As-
sociation under its Commercial Arbitration Rules.
You may file for arbitration at any AAA location in
the United States upon the payment of the appli-
cable filing fee. The arbitration will be conducted
before a single arbitrator, and will be limited
solely to the dispute or controversy between you
and Panamax. The arbitration shall be held in any
mutually agreed upon location in person, by tele-
phone, or online. Any decision rendered in such
arbitration proceedings will be final and binding
on each of the parties, and judgment may be en-
tered thereon in a court of competent jurisdiction.
The arbitrator shall not award either party special,
exemplary, consequential, punitive, incidental or
indirect damages, or attorney’s fees. The parties
will share the costs of arbitration (including the
arbitrator’s fees, if any) in the proportion that
the final award bears to the amount of the initial
claim.
9. GENERAL: If you have any questions regarding
the product warranty or the connected equip-
ment protection policy, please contact the Pan-
amax Customer Relations Department at www.
panamax.com. The Limited Product Warranty
and Connected Equipment Policy herein super-
sede all previous warranties and/or Connected
Equipment repair/replacement policies.
THE LIMITED PRODUCT WARRANTY IS THE
ONLY WARRANTY PROVIDED WITH THIS PAN-
AMAX PRODUCT AND ANY OTHER IMPLIED
OR EXPRESSED WARRANTIES ARE NON-EX-
ISTENT.
This warranty may not be modified except in
writing, signed by an officer of the Panamax
Corporation.
* The use of a Panamax extension cord or
equivalent (UL or CSA listed, minimum
14AWG, 3-wire grounded) will not invalidate
the warranty.
** Forms are available on the Panamax web
site for requesting RAs and opening a claim
for connected equipment damage.
MODEL - MR5100
DOC. NO. DWS-00007-D
Effective Date 7/1/12
Contacting Panamax
Panamax, Inc.
1800 South McDowell Blvd.
Petaluma, CA 94954
Phone - 707-283-5900 or 800-472-5555
Fax - 707-283-5901
Web - www.panamax.com
Customer Relations
7:30 AM – 4:30 PM, M-F
Email - custrelations@panamax.com
www.panamax.com
1800 South McDowell Blvd., Petaluma, CA 94954 800-472-5555 707-283-5900 Fax 707-283-5901 www.panamax.com
2014 Core Brands, LLC. All rights reserved. Panamax is a registered US trademark of Core Brands LLC a Nortek, Inc. companny.
MODEL UNIT DIMENSIONS WEIGHT CARTON DIMENSIONS WEIGHT UPC MASTER PACK QTY MASTER PACK UPC
MR5100 12”l x 17”w x 3.5”h 13.5 lbs 20” x 24” x 10.3” 18 lbs 050616008945 1 50050616008940
4”h with feet
Part# L655 Rev.G
6SHFLÀFDOO\GHVLJQHGDQGHQJLQHHUHGWRSURYLGHSURWHFWLRQÀOWUDWLRQDQG
SRZHUPRQLWRULQJIRU\RXUKRPHWKHDWHUV\VWHP
Specifications subject to change due to product upgrades and improvements
*
Go to www.panamax.com for detailed noise filtering information.
HOME THEATER POWER MANAGEMENT
• 11 Protected & Filtered Power Outlets
• Exclusive Automatic Voltage Monitoring (AVM)
C US
Antenna, Cable, or Satellite, TEL and LAN Signal Protection
• 10 ft. Power Cable with Straight Plug
SPECIFICATIONS
FEATURES
WEIGHTS, DIMENSIONS AND UPC CODES
0RGHO MR5100
AC PROTECTION
Protect or Disconnect Circuitry__________________________________________Yes
Patented Power Management Circuit_____________________________________Yes
Overvoltage Shutoff____________________________________________140V ±3V
Undervoltage Shutoff___________________________________________100V ±/-1V
Thermal Fusing____________________________________________________Yes
Line Voltage____________________________________________120VAC, 50/60HZ
Initial Clamping Level__________________________________200V Peak, 141VRMS
Voltage Protection Rating (UL 1449 3rd Edition, 3,000A)____________________400V
Protection Modes___________________________________________ L-N, L-G, N-G
Maximum Current Rating______________________________________15A (1800W)
EMI/RFI Noise Filtration__________________________Panamax Level 4 Noise Filtration*
Response Time___________________________________________________< 1ns
Single Pulse Energy Dissipation__________________________________2025 Joules
Peak Impulse Current____________________________________________52,000 A
TEL PROTECTION
Fuseless / Auto-Resetting______________________________________________Yes
Clamping Level __________________________________________________ 260V
Wires Protected _________________________________________ 2 Wire, 1 Pair (4, 5)
Connectors_________________________________________________RJ-11
LAN PROTECTION
Clamping Level___________________________________________62±6V @ 1 mA
Compatibility___________________________________________10/100/1000bT
Wires Protected_________________________________________________8-Wires
Connectors_____________________________________________________RJ-45
UNIVERSAL COAX PROTECTION
HD 1080 i/p Ready_________________________________________________Yes
Bidirectional_____________________________________________________Yes
Shielded_______________________________________________________Yes
Clamping Level____________________________________________________75V
Frequency Range__________________________________________OMHz - 2.2 GHz
Insertion Loss__________________________________________________<0.5 dB
Connections________________________________________Female “F”, Gold Plated
POWER ON / OFF ON / OFF, CONTROL FOR
DECORATIVE BLUE LIGHTS
(Blue lights can be illuminated when power is off)
SAFE POWER AND
VOLTAGE INDICATOR
UNSAFE VOLTAGE
INDICATOR
LINE FAULT
INDICATOR
FRONT PANEL
CONVENIENCE OUTLET
OUTLET BANKS 1, 2 and 3
INDICATOR LEDS USB CHARGER
ALL AC OUTLETS (FRONT AND BACK) INCLUDE SURGE PROTECTION AND POWER FILTRATION
LAN SURGE PROTECTION
1 PAIR OF RJ-45 IN/OUT
CONNECTORS
COAXIAL SURGE PROTECTION
2 PAIRS UNIVERSAL IN/OUT
CONNECTORS
RACK MOUNTABLE
(RACK EARS INCLUDED)
TELCO SURGE PROTECTION
1 PAIR OF RJ-11 IN/OUT
CONNECTORS
GROUND LUG
FT STRAIGHT PLUG
15 AMP CIRCUIT
BREKAER
RESETTABLE
OUTLET BANK 3 (HIGH CURRENT) OUTLET BANK 2 (SWITCHED) OUTLET BANK 1 (ALWAYS ON) with INDICATOR LIGHT
• Protect or DisconnectTechnology
• Linear Level 4 Noise Filtration
10 F
10 F


Product specificaties

Merk: Panamax
Categorie: Niet gecategoriseerd
Model: MR5100
Kleur van het product: Zwart
Gewicht: 6123.497 g
Breedte: 431.8 mm
Diepte: 304.8 mm
Hoogte: 88.9 mm
Snoerlengte: - m
Aan/uitschakelaar: Ja
Aantal Ethernet LAN (RJ-45)-poorten: 2
Responstijd: 1 ms
Frequentie: 0 - 22000 MHz
Rack-montage: Ja
AC-ingangsfrequentie: 50 - 60 Hz
Surge energy rating: 2025 J
Aantal AC uitgangen: 11 AC-uitgang(en)
Nominale input voltage: 120 V
Aantal per doos: 1 stuk(s)
EMI/RFI geluidsfiltering: Ja
Piekstroom, common mode: 15 A
Klem voltage: 200 V

Heb je hulp nodig?

Als je hulp nodig hebt met Panamax MR5100 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Panamax

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd