PAC TATO Handleiding

Bekijk gratis de handleiding van PAC TATO (2 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 65 mensen en kreeg gemiddeld 4.1 sterren uit 5 reviews. Heb je een vraag over PAC TATO of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Pacic Accessory Corporation - Santa Ana, CA 92705

866-931-8021 • www.pac-audio.com

DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the TATO be held liable for consequential damages sustained in

connection with the TATO. The manufacture and it’s distributors will not, nor will they authorize any representative or any other individual to assume

obligation or liability in relation to the TATO other than its replacement.

06-29-10

J1850

Class 2

VPW

Class 2

J1850

10001 1 101 1 1 1001001 101 100

1 11 0 1 0 00 0 1 1 0 110 1 11 0 0 1 1 0 0

Arbitration

EOD

CRC

10001 1 101 1 1 1001001 101 100

11 1 0 1 0 00 0 1 1 0 110 1 11 0 0 1 1 0 0

Class 2

Class 2

J1850

TATO

JBL Amplier Turn-On Interface for

Toyota CANbus Vehicles

The TATO is designed to control the power and audio levels of the factory installed

JBL amplier allowing the OEM radio to be removed and replaced with an aftermarket

stereo.

Installation:

Note: BEFORE REMOVING THE FACTORY RADIO: BALANCE AND FADE IT TO THE CENTER, TURN THE

RADIO UP TO AT LEAST 3/4 VOLUME, TURN THE RADIO OFF, TURN THE IGNITION OFF & THEN PROCEED

WITH REMOVING THE FACTORY RADIO

Disconnect the factory radio from the OEM wiring harness and remove it from the vehicle. Make the

following connections of the TATO wiring harness to the aftermarket radio:

Connections:

Yellow Wire - Connect to 12 Volt Constant Power on aftermarket radio•

Red Wire - Connect to Accessory on aftermarket radio•

Black Wire - Connect to Ground on aftermarket radio•

Orange/White Wire - Connect to Dimmer on aftermarket radio•

*11 Pin Harness - Connect to PAC’s SWI-X, SWI-JACK, SWI-PS or SWI-ECL2 (Sold Separately) •

Red Bullet Connector - Connect to Accessory

Black Bullet Connector - Connect to Ground

Connect the 4 RCA connectors to the RCA outputs of the aftermarket radio •

Front Left - White RCA Front Right - Grey RCA

Rear Left - Green RCA Rear Right - Purple RCA

If connecting the TATO to a head unit with only 2 Channel RCA outputs, use two pairs of RCA splitters (1M-2F) to split the signal. Failure to connect all 4 inputs

of the TATO will result in loss of audio performance. Fade audio controls will only function with a 4 channel aftermarket deck.

Connections to the TATO Interface:

Connect 24-pin translucent connector •

to the side of the TATO.

Connect 8-pin DIN cable to the plug on •

the side of the TATO.

Connections to the Vehicle:

Plug the main 20-pin Toyota harness into the matching factory wir-•

ing harness.

*

•

If using PAC’s SWI-X, SWI-JACK, SWI-PS or SWI-ECL2, Plug

the smaller 20-pin harness into the matching factory wiring har-

ness. Program PAC’s SWI-X, SWI-JACK, SWI-PS or SWI-ECL2

for version #8 and follow the programming instructions included

with PAC’s SWI-X, SWI-JACK, SWI-PS or SWI-ECL2.

Product specificaties