PAC HDK001X Handleiding

Bekijk gratis de handleiding van PAC HDK001X (4 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 13 mensen en kreeg gemiddeld 4.9 sterren uit 3 reviews. Heb je een vraag over PAC HDK001X of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Page 1

HDK001X

Aftermarket Stereo Dash Kit for

Select Harley-Davidson Motorcycles

Pacic Accessory Corporation

® | 866-931-8021 | [email protected]

©2016 Pacic Accessory Corporation

www.pac-audio.com Rev. 012016

Pifi ACti

PAC is an AAMP brand

Parts List

The HDK001X includes everything you will need for proper mounting of an aftermarket radio into

the dash of your motorcycle. This kit contains the following parts:

1. Dash Kit

• (x2) Face plates (one is equipped with a splash guard)

• (x2) Mounting Brackets (one left and one right)

• (x4) Stainless steel bolts (short)

• (x4) Stainless steel nuts

• (x2) Spacers (used for Road Glide models only)

• (x4) Stainless steel bolts (long - for use with spacers)

2. Rubber Gasket Ring

3.Wiringharness(pre-wiredwithpower,speaker&SWI-HDspecicconnector)

4.SWI-HD(pre-programmedwithcustomHarleyrmware-noinitialprogrammingnecessary)

Required Tools

The following is a list of tools (not included) you will need to complete this installation.

• T-25 Torx driver

• T-27 Torx driver

• 3/16” or 5mm Hex Socket

• 1/4” or 6mm long shaft Hex Socket

• 7/16” Socket/ratchet combo or box wrench (Road Glide models only)

Fairing Disassembly

0

20

30

70

80

40

50

60

10

0

10

30

20

50

40

110

120

60 70

80

90

100

MPH

H

A

R

L

E

Y

-

D

A

V

I

D

S

O

N

C

E

R

T

I

F

I

E

D

RPM

x100

H

A

R

L

E

Y

-

D

A

V

I

D

S

O

N

1

2

3

4 5

76

Removal of the outer fairing and windshield:

1. Drape front fender area with protective material/

pad to prevent scratching or damaging the paint.

2. From the front of the motorcycle, loosen the three

T27 TORX screws located (Numbered 1, 2 & 3 on

illustration) below the windshield.

3. Raise and remove the windshield from the inner

and outer fairings.

4. Remove the two T27 TORX screws located on

outer sides of the speakers (Numbered 4 & 5 on

illustration).

5. Turn the handlebar to the right and remove the

T-27 TORX screw (Number 6) by reaching below

the left side of the fairing cap.

6. Turn the handlebar to the left and remove the T-27

TORX screw (Number 7) by reaching in below the

right side of the fairing cap.

CAUTION: When working on FLHX models, be sure

to hold the outer fairing in place when removing the

last screw. Without the auxiliary lamps to hold it

in place, the outer fairing will drop and can cause

damage to the fairing or fender.

7. From the front of the motorcycle, remove the three

screws below the windshield. (Previously loosened

in step 2)

8. Tilting the outer fairing forward, remove head lamp

connector at the back of the head lamp assembly.

9. Lift the outer fairing off the motorcycle.

2006-2013 FLHX Street Glide & 1996-2013 FLHT Electra Glide Models

FLTR (Road Glide) instructions on next page

Product specificaties