PAC RPK5-GM4102 Handleiding

PAC Niet gecategoriseerd RPK5-GM4102

Lees hieronder de đź“– handleiding in het Nederlandse voor PAC RPK5-GM4102 (9 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 35 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/9
C
Page 1
© 2019 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
Email - support@pac-audio.com - Phone: 727-592-5991
Complete Radio Replacement Kit with Integrated Climate
Control Retention for 2010-2015 Chevrolet Camaro
RPK5-GM4102
Rev: R6
Date: 010419
Parts List
The RPK5-GM4102 includes everything you need for a professional installation of an aftermarket radio in your Camaro.
This kit contains:
1. Dash Kit
• (x1) PAC HVAC Control Panel (including factory style HVAC knobs)
• (x2) Radio Mounting Brackets (One left and one right)
• (x1) Pocket (For single DIN applications)
• (x8) Radio Mounting Screws
2. RP5-GM4101 (Camaro speciîšżc radio replacement module)
3. Camaro speciîšżc antenna adapter (BAA-DIN22).
4. Reverse camera retention harness for vehicles equipped with the MyLink system.
5. USB retention cable. This cable is compatible with vehicles equipped with the MyLink radios and vehicles equipped with the standard
non-touchscreen radios. It will require that the cable be ran to the back of the center console.
6. AUX retention cable for 2010-2012 vehicles equipped with the standard non-touchscreen radios and a USB port.
Overview
The RPK5-GM4102 is a complete radio replacement kit with integrated climate control retention for the 2010-2015 Chevrolet Camaro. This
kit comes equipped with factory style HVAC control knobs for a factory look and experience. To add to the factory look and experience, the
exterior temperature display is retained by a small OLED display at the top of the kit retaining this valuable vehicle feature. This kit also
includes all of the modules and cables needed to retain all of the important features of the factory system such as OnStar, factory warning
chimes, factory Bluetooth, steering wheel mounted radio controls, factory reverse camera, factory ampliîšżer (if equipped), factory AUX jack
(if equipped) and the factory USB port (if equipped). The RPK5-GM4102 also provides data bus driven outputs such as retained accessory
power (RAP), vehicle speed sensor (VSS), illumination, reverse trigger and parking brake. Use of this interface also allows you to program
two radio functions to each SWC button by using short press long press dual command functionality.
Important Notes
1. These instructions only apply to or later revisions of the RP5 interface. The revision info can be found on a small white sticker on the R.2.5.6.3
interface.
2. The center inserts on the control knobs are made to install once! They are not easily removable / swappable. Please ensure you have selected
the correct inserts for your installation before snapping the inserts into the control knobs.In the event that the center inserts need to be removed,
see the troubleshooting section on page 9.
3. For vehicles with heated seats: When installing the center caps, you need to îšżrst install the light pipes. They are keyed so they will only îšżt one
way. Pay close attention to the shape and orientation of the light pipes to ensure correct lighting.
4. When discussing the control knobs, we will refer to “Left” indicating the driver side, and “Right” indicating the passenger side.
5. It is recommended that the user’s phone(s) be “Unpaired” from the factory Bluetooth. This will ensure the user’s phone will always pair to the
aftermarket radio’s bluetooth.
6. Once the radio has been removed, the vehicle settings which are normally selected through the factory radio can be accessed using the
PAC-UP along with the PAC Vehicle Settings program (for windows PC), which can be downloaded here: http://www.pac-audio.com/
îšżrmware.
7. The Answer/Voice and End/Mute buttons can be set to control the factory OnStar functions, or to control the aftermarket radio. This option can
be found in the PAC Vehicle Settings program mentioned above in note one. The default setting for these buttons is to control the factory OnStar.
If these buttons are set to control the aftermarket radio, OnStar can still be accessed by using the mirror controls.
8. The radio replacement interface comes pre-programmed for all of the vehicle’s factory SWC functions and does not require programming unless
you wish to re-assign the SWC functions or utilize the short press long press dual command functionality. The SWC can always be restored to
default settings by pressing and releasing the program button on the side of the interface once and waiting 7 seconds for the LED to ash 4 times.
9. The radio select rotary switch on the side of the interface must be adjusted to the proper radio setting before plugging the interface into the
vehicle (see page 4 for setting chart).
C
Page 2
© 2019 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
Email - support@pac-audio.com - Phone: 727-592-5991
Complete Radio Replacement Kit with Integrated Climate
Control Retention for 2010-2015 Chevrolet Camaro
RPK5-GM4102
Rev: R6
Date: 010419
1.3 1 - Remove the 4 x 7mm bolts ( ) securing the radio
( ) into the dash. Slide the radio ( ) to the rear and 2 2
disconnect all electrical connections.
You can now set the factory radio aside as it will not
be needed any longer.
Proceed to the next section to transfer the retention
clips from the factory radio control assembly to the
PAC HVAC control assembly.
Removing the factory radio from the vehicle
1.1 - Apply the parking brake. Move the transmission shift
assembly to the most rearward position possible. Use a at
bladed plastic trim tool to release the retainer tabs securing
the front oor console front cover to the console assembly.
Lift the cover ( ) up and towards the rear, making sure that 1
the accessory power receptacle and the electronic traction
control switch clears the transmission shift assembly. It may
be necessary to pop these items loose from the underside to
achieve clearance. Disconnect the harnesses.
1.2 - 1 Remove the 2 x 7mm bolts ( ) securing the radio
control assembly (2) into the dash. Then use a at-
bladed plastic trim tool to release the retainer clips
securing the radio control assembly ( ) to the instrument 2
panel. Disconnect the electrical connections.
C
Page 3
© 2019 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
Email - support@pac-audio.com - Phone: 727-592-5991
Complete Radio Replacement Kit with Integrated Climate
Control Retention for 2010-2015 Chevrolet Camaro
RPK5-GM4102
Rev: R6
Date: 010419
Dash Panel Assembly
2.1 - Using a at bladed pry tool, carefully remove two of the
retention clips off of the black plastic backing of the factory radio
control assembly.
2.2 - Slide the retention clips (removed during the previous
step) onto the two black posts at the top of the PAC HVAC
control assembly.
To secure the top of the PAC HVAC control assembly into the dash, remove two of the retention clips located on the back side at the top of the
factory radio control assembly, and reuse them on the PAC HVAC control assembly.
Knob Inserts
For vehicles without heated seats: Remove the center cap called “Blank Left” and snap that into the climate control knob labeled Left. The insert
is keyed, so it will only t in one orientation. Remove the center cap called “Blank Right” and snap it into the climate control knob labeled Right.
For vehicles equipped with heated seats: Carefully open the package labeled “Heated Seat Left”. There will be a center cap and 2 small, clear
plastic, light pipes. They are keyed, so they will only îšżt in one speciîšżc hole each.
1. From the front of the control knob, insert the light pipes (non-keyed side îšżrst) into the small rectangular openings.
2. The left light pipe (A) has a key tab on the narrow side. Insert this light pipe with the key facing down.
3. The right light pipe (B) has the key tab on the wide side. Insert this light pipe with the key facing to the right.
(A)
(B)
Close-up of light pipes installed
key tab
key tab

Product specificaties

Merk: PAC
Categorie: Niet gecategoriseerd
Model: RPK5-GM4102

Heb je hulp nodig?

Als je hulp nodig hebt met PAC RPK5-GM4102 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd PAC

PAC

PAC LPHHD04 Handleiding

6 Maart 2024
PAC

PAC RP4.2-TY13 Handleiding

8 December 2023
PAC

PAC PGHGM2 Handleiding

7 Juli 2023
PAC

PAC CAM-TY12 Handleiding

6 Juli 2023
PAC

PAC VCI-NIS2 Handleiding

24 Juni 2023
PAC

PAC SNI-1/3.5 Handleiding

22 Juni 2023
PAC

PAC ANC-CH01 Handleiding

21 Juni 2023
PAC

PAC RP4-FD11 Handleiding

20 Juni 2023
PAC

PAC AP4-GM61 Handleiding

19 Juni 2023
PAC

PAC IGN-3 Handleiding

19 Juni 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Playtive

Playtive IAN 327221 Handleiding

1 Mei 2024
Samsung

Samsung UN32J4001AF Handleiding

1 Mei 2024
Bauknecht

Bauknecht KSI 18GF2 P2 Handleiding

27 April 2024
Fakir

Fakir Artemis TS 150 Handleiding

26 April 2024
Sony

Sony UTX-M03 Handleiding

26 April 2024
Sony

Sony URX-P03 Handleiding

26 April 2024
Sony

Sony WRU-806B Handleiding

26 April 2024
Sony

Sony UTX-B03 Handleiding

26 April 2024
Sony

Sony UTX-P03 Handleiding

26 April 2024
Sony

Sony ODS-L10 Handleiding

26 April 2024