PAC RP5-GM11 Handleiding

Bekijk gratis de handleiding van PAC RP5-GM11 (8 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 118 mensen en kreeg gemiddeld 4.0 sterren uit 7 reviews. Heb je een vraag over PAC RP5-GM11 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

C

Radio Replacement & Steering Wheel Control Interface

with OnStar Retention for General Motors Vehicles

RP5-GM11

Rev. 092617

Page 1

© 2017 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.

PAC-audio.com

Introduction & Features

Important Notes

Wiring Connection Chart

Illustration / Schematic

The RP5-GM11 interface allows the replacement of a factory radio in select General Motors vehicles with Class II radios.

Using this interface will retain factory features such as OnStar, steering wheel controls (SWC), warning chimes, Rear

Seat Controls (RSC), Rear Seat Entertainment (RSE) and the BOSE amplier when the original radio is removed. The

RP5-GM11 also provides data bus driven outputs such as retained accessory power (RAP), vehicle speed sensor (VSS),

illumination, reverse trigger and parking brake.

1. These instructions only apply to R.2.2.6.8 or later revisions. The revision info can be found on a small white sticker on the

interface and packaging.

2. The radio select rotary switch on the side of the interface must be adjusted to the proper radio setting before plugging the

interface into the vehicle (see next page for setting chart).

3. The interface comes pre-programmed for all of the vehicles factory SWC functions and does not require programming unless

you wish to re-assign the SWC functions to different buttons. The SWC can always be restored to default settings by pressing

and releasing the program button on the side of the interface once and waiting 7 seconds for the LED to ash 3 times. PLEASE

NOTE: Due to the many different possible OEM SWC congurations, some applications may need to be reprogrammed

for the SWC assignments to make sense. Whatever you assign as aftermarket volume commands will also be the

OnStar volume commands.

4. The aftermarket radio must have an auxiliary input in order for the factory RSE audio to be retained through the cabin speakers.

5. RSC buttons that are identical to the SWC will mimic the SWC one for one.

6. The LED will ash whenever a SWC button is pressed.

SWC Connection

See above chart for

different radio type

connections

Wiring

SWC Connection

Aftermarket

Radio

Connections

Vehicle

Connections

Light GreenParking Brake Output (-)

PinkVehicle Speed Output

BlueNot Used

Blue / WhiteAmp Turn On Input

Orange / WhiteIllumination Output (+)

Purple / WhiteReverse Output (+)

Brown Loop

Mute Loop - See

installation note 6.

Aftermarket Radio Connections

Yellow *+12v from RP5

Yellow *+12v from vehicle

Black **Ground from RP5

Black **Ground from vehicle

RedAcc. Output

WhiteFront Left + input

White / BlackFront Left - input

GreyFront Right + input

Grey / BlackFront Right - input

GreenRear Left + input

Green / BlackRear Left - input

PurpleRear Right + input

Purple / BlackRear Right - input

SWC Connector

Blue / YellowKenwood, Newer JVC

3.5mm Jack

Alpine, JVC, Clarion,

Pioneer, Sony, Fusion,

Boyo, Dual, Lightning Audio,

Visteon or Advent

IMPORTANT NOTES REGARDING YELLOW AND BLACK WIRE CONNECTIONS

* Connect both Yellow wires from the

RP5 harnesses to the radio’s 12v

constant input.

** Connect both Black wires from the

RP5 harnesses to the radio’s ground

input.

Product specificaties