PAC APH-TY03 Handleiding

Bekijk gratis de handleiding van PAC APH-TY03 (20 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 18 mensen en kreeg gemiddeld 4.7 sterren uit 6 reviews. Heb je een vraag over PAC APH-TY03 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Speaker Connection Harness for Select

For Select Toyota Vehicles with Factory Ampliers

Equipped with a 20-Pin Connector

APH-TY03

C

Page 1

Copyright © 2019. All rights reserved. PAC is a Power Brand of AAMP Global.

PAC-audio.com

Rev: V1

Date: 010419

APH-TY03-HAR

1

11

12

20

121

2011

WhitBlacke /

Yellow

White

Yellow

Gray / BlackGray

Purplek / Blac

GreeBlackn /

Purple

Green

Black

Black

Orangek / Blac

Blue / Black

Orange

Blue

BrowBlackn /

ReBlackd /

Brown

Red

WhitBlacke /

Yellow

White

Yellow

Gray / kBlacGray

Purplek/ Blac

GreeBlackn /

Purple

Green

Black

Black

Orangek/ Blac

Blue /kBlac

Orange

Blue

ReBlackd /

BrowBlackn /

Red

Brown

Introduction and Features

The APH-TY03 simplies speaker wire connections when adding aftermarket ampliers. Aftermarket ampliers can

be easily added with no need to cut or modify a vehicle’s original wiring. Each pair of wires has been labeled with the

corresponding speaker name.

Wiring Overview

Installation Notes

1. It is always best to use a tone generator (PAC part number: TL-PTG2) to verify that the tables in this manual, and the labels

on the wires, match the wiring in your specic vehicle.

2. The Gray 20-pin connector from the APH-TY03 must be connected to the factory amplier when using a PAC AmpPRO

Interface.

3. Not all applicable vehicles will come equipped with a corresponding speaker for all of the wires populated in our harness. It is

important to understand which speakers are equipped in your vehicle.

4. If you are leaving any of the factory speakers connected to the factory amplier, simply connect the speaker wires (color for

color) between the male and female connectors, for the speakers that will be powered by the factory amplier. For example:

If you want the rear speakers to be powered by the factory amplier, simply connect the Green, Green / Black, Purple and

Purple / Black wires from the male connector to the Green, Green / Black, Purple and Purple / Black wires from the female

connector.

5. For vehicles that lose audio output when there is no load on the speaker outputs of the factory amplier, PAC load resistors

will be required (PAC Part Number LR335 or LR475).

1. Locate the vehicle’s factory amplier and disconnect the 20-pin connector.

2. Connect the APH-TY03 harness to the connector that was disconnected in the previous step.

3. Connect the male connector from the APH-TY03 to the amplier.

4. Connect the longer loose wires from the APH-TY03, to your aftermarket amplier or passive crossovers, according to the

tables in this manual.

5. Insulate unused wires in the 20-pin connector that plugs into the factory amplier side of the APH-TY03.

Installation Steps

Connect to aftermarket

amplier or passive

crossover

Insulate any unused wires

1 Yellow

12 Yellow

2

White / BlackSpeaker 1 -

13

WhiteSpeaker 1 +

3

Gray / BlackSpeaker 2 -

14

GraySpeaker 2 +

4

Green / BlackSpeaker 3 -

15

GreenSpeaker 3 +

5

Purple / BlackSpeaker 4 -

16

PurpleSpeaker 4 +

6

Black

7

Black

8

Blue/Black Speaker 5 -

17

BlueSpeaker 5 +

9

Orange/Black Speaker 6 -

18

OrangeSpeaker 6 +

10

Red / BlackSpeaker 7 -

19

RedSpeaker 7 +

11

Brown / BlackSpeaker 8 -

20

BrownSpeaker 8 +

Speaker 8

Pass through (Ground)

Speaker 1

Speaker 2

Speaker 3

Speaker 4

Speaker 5

Speaker 6

Speaker 7

Pin NumberWire ColorWires DescriptionLabel

Pass through (Constant 12v)

Product specificaties