PAC AP4-TY12 Handleiding

PAC Niet gecategoriseerd AP4-TY12

Lees hieronder de 📖 handleiding in het Nederlandse voor PAC AP4-TY12 (5 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 12 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/5
© 2017 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
C
Page 1
Rev. 111317
Advanced Ampliîš¿er Interface
for Select Toyota / Lexus Vehicles
AP4-TY12
The AP4-TY12 provides a 6-channel pre-amp output for use with aftermarket audio equipment. Using the full range,
îš¿xed level head unit output, in conjunction with data bus messages, the AP4-TY12 delivers a variable 5v RMS pre-
amp output with fading, balance, equalization, and level control capabilities. The module also retains audio from
other vehicle features such as factory navigation prompts, Bluetooth and Voice Activation. An accessory controlled
remote ampliîš¿er turn on wire is also provided by the AP4-TY12. When used in conjunction with the APA-TOS1 (sold
separately), the module can provide a variable 2-channel îš¿ber optic digital audio output (TOSLINK).
Introduction and Features
Important Notes
1. Only compatible in vehicles equipped with a data bus controlled premium sound system. To verify compatibility in Toyota,
look for a JBL logo on the radio. In Lexus, compatible applications will have a center channel or factory subwoofer.
2. The AP4-TY12 does not support retention of the Easy Speak function.
3. Toyota Safety Connect and Lexus Enform (SOS) can easily be retained. See the Tech Brief "AP4-TY12 SOS Retention" at
PAC-audio.com for detailed instructions.
4. The factory radio's speed controlled volume, DSP, and surround sound mode are not supported by the AP4 outputs.
5. The factory ampliîš¿er must remain connected, and in the vehicle after the AmpPRO has been installed.
6. Prior to testing, cycle the ignition off and back on again to properly initilize the AP4-TY12.
7. The radio's beep setting must be enabled on the factory radio in order to hear the audible tones when making selections
through the radio.
8. Initially, if the beep through the AP4-TY12 does not match the on / off selection through the radio, cycle the beep to the
opposite setting and back, then test again.
9. The radio's beep volume and minimum volume levels are set to 0 dB by default. If you are happy with this level in your
particular application, additional adjustment is not required. Please refer to the Setup and Conîš¿guration section on page 2
for more details.
10. The Radio's Nav / VR Voice, incoming E-mail tone, Ringtone, In-Call, Incoming SMS / MMS tone and Incoming SMS Voice
volumes can be adjusted through the radio's settings menu as they were prior to installation of the AP4-TY12.
11. The remote output is rated at 2A of current. If more current is needed, an external relay must be used.
12. Channels 5 and 6 are non-fading outputs. The output level of channels 5 and 6 can be controlled using the supplied level
control knob.
13. The level control knob must be connected in order to manually adjust the beep volume and minimum volume settings.
14. No adjustments can be made manually using the programming button when the module is connected to a PC.
15. Due to variations between various OEM radios and even between radio modes, the radio output voltage may vary slightly
from the selected 5 volt (or 4 volt when DIP switch 2 is down) output.
Wiring Connection Chart
To Aftermarket
Amplier
Non-FadingRearFront
1(L) 2(R) 4(R) 5(L) 6(R)3(L)
To Radio
Non-Fading
Level Control
Knob
To Vehicle
Harness
28 - Pin
6 - Pin
10 - Pin
AP4-TY12-HAR
Remote Turn On Output (2A Max)
Mute Input From Navigation *
Mute Input From Telematics *
* See Page 2 Installation Notes 11 and 12 for further details regarding the Mute Input leads.
© 2017 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
C
Page 2
Rev. 111317
Advanced Ampliîš¿er Interface
for Select Toyota / Lexus Vehicles
AP4-TY12
Setup and Conîš¿guration
1. Turn the ignition on. LED 1 on the interface will turn on and the +12v remote output will turn on.
2. Set the amp gain(s) to the desired level. We recommend using an oscilliscope and test tones to set the amp gain(s). Please
refer to the MECP Advanced study guide (p. 360) if you are unfamiliar with this process.
3. Check volume, balance, fade and EQ settings.
4. If you would like to adjust the radio's beep volume or minimum volume, do so using one of the methods outlined below. If
you are happy with the default levels, no adjustments are necessary.
Manually Setting the Radio's Beep Volume
You can manually set the level of the factory radio beeps using the programming button on the side of the interface. If you would
like to set the beep volume using the PC app please proceed to the PC App section.
PLEASE NOTE: Level control knob must be connected to the module in order to set the Radio's Beep Volume.
Installation
1. Remove factory radio.
2. Disconnect the 28-pin harness, the 10-pin harness and the 6-pin harness from the radio.
3. Connect AmpPRO harnesses to vehicle harnesses.
4. Connect AmpPRO harnesses to factory radio.
5. Set any feature DIP switches that apply to your install.
a. DIP switch 1 is used for two channel mode. In this mode, both the TOSLINK and front RCA outputs (1 and 2) become
non-fading outputs.
b. Set DIP switch 2 on (down) to lower the RCA output voltage to 4v. Leave DIP switch 2 off (up) to keep the RCA output
voltage at 5v. See troubleshooting section on page 5 for more details.
c. DIP switches 3 and 4 are not used and should remain off (up).
6. If you are using the APA-TOS1 (sold separately) refer to the instructions included with that product for its installation.
7. Connect the AmpPRO harness to the module.
8. Connect the level control knob to the module and install in an accessible location.
9. Connect the signal cables and remote input from the aftermarket ampliîš¿er.
10. Initially, if the beep through the AP4-TY12 does not match the on / off selection through the radio, cycle the beep to the
opposite setting and back, then test again.
11. The Yellow / Black "Mute Input from Telematics" wire will be used in conjunction with the Safety Connect / Lexus Enform
(SOS) Retention. See the Tech Brief "AP4-TY12 SOS Retention" at PAC-audio.com for detailed instructions.
12. The Brown "Mute Input From Navigation" is a spare mute lead that can be used for custom applications. The audio will be
muted whenever the Brown wire is supplied a ground.
DIP
1234
ON
Two Channel Mode 5v / 4v Preout Not Used Not Used
1 2 3 4
Set DIP switches to the ON position to activate the corresponding features.
Set DIP switches to the OFF position for any features that are not desired.
Module Layout
LED 1
Interface Connector 1
Expansion Port
TOSLINK Output
(APA-TOS1 sold separately)
Programming Button
Feature Select
DIP switches
Front Output
Ch. 1(L) and 2(R)
Non-Fading Level Control
Knob Connection
USB Connection Rear Output
Ch. 3(L) and 4(R)
Non-Fading Output
Ch. 5(L) and 6(R)
LED 2
© 2017 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
C
Page 3
Rev. 111317
Advanced Ampliîš¿er Interface
for Select Toyota / Lexus Vehicles
AP4-TY12
Setup and Conîš¿guration (cont.)
Setting the radio's beep volume using the programming button
1. Start with the level control knob turned all the way down (counter-clockwise).
2. Press the programming button on the side of the interface.
3. LED 1 will turn green and beeps will begin continuously sounding.
4. Turn the level control knob clockwise until the desired beep volume level is reached.
5. You can now either press the programming button twice or wait ten seconds to exit the settings.
Manually Setting the Minimum Volume
If the minimum volume of the radio (factory radio volume level 1) is too loud, you can manually set the level of the minimum
volume using either the programming button on the side of the interface or the factory SWC. If you would like to set the
minimum volume using the AmpPRO app, please proceed to the AmpPRO App section.
PLEASE NOTE: Level control knob must be connected to the module in order to set the Minimum Volume.
Setting the minimum volume using the programming button
1. Start with the level control knob turned all the way down (counter-clockwise).
2. Set the amp gains to the desired level.
3. Set the volume on the factory radio to 1.
4. Press the programming button on the side of the interface twice.
5. LED 1 will turn amber and the chimes will begin sounding every îš¿ve seconds.
6. Turn the level control knob clockwise until the desired minimum volume level is reached.
7. You can now either press the programming button once or wait ten seconds to exit the settings.
Use of the AmpPRO App allows
you to do the following:
• Congure User Interface Options such
as:
• Minimum Volume Level
• Chime (Radio Beeps) Volume Level
• Enable / Disable AP4 Chimes (Radio
Beeps)
• Enable / Disable factory EQ
• Bass / Mid / Treble boost frequencies
and Q factor
• Update Product Firmware
• Read Firmware / Hardware Versions
• You can download the Amp PRO app at :
http://aampglobal.com/appdownloads
AmpPRO App

Product specificaties

Merk: PAC
Categorie: Niet gecategoriseerd
Model: AP4-TY12

Heb je hulp nodig?

Als je hulp nodig hebt met PAC AP4-TY12 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd PAC

PAC

PAC LPHHD04 Handleiding

6 Maart 2024
PAC

PAC RP4.2-TY13 Handleiding

8 December 2023
PAC

PAC PGHGM2 Handleiding

7 Juli 2023
PAC

PAC CAM-TY12 Handleiding

6 Juli 2023
PAC

PAC VCI-NIS2 Handleiding

24 Juni 2023
PAC

PAC SNI-1/3.5 Handleiding

22 Juni 2023
PAC

PAC ANC-CH01 Handleiding

21 Juni 2023
PAC

PAC RP4-FD11 Handleiding

20 Juni 2023
PAC

PAC AP4-GM61 Handleiding

19 Juni 2023
PAC

PAC IGN-3 Handleiding

19 Juni 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Playtive

Playtive IAN 327221 Handleiding

1 Mei 2024
Samsung

Samsung UN32J4001AF Handleiding

1 Mei 2024
Bauknecht

Bauknecht KSI 18GF2 P2 Handleiding

27 April 2024
Fakir

Fakir Artemis TS 150 Handleiding

26 April 2024
Sony

Sony UTX-M03 Handleiding

26 April 2024
Sony

Sony URX-P03 Handleiding

26 April 2024
Sony

Sony WRU-806B Handleiding

26 April 2024
Sony

Sony UTX-B03 Handleiding

26 April 2024
Sony

Sony UTX-P03 Handleiding

26 April 2024
Sony

Sony ODS-L10 Handleiding

26 April 2024