PAC APH-TY04 Handleiding

Bekijk gratis de handleiding van PAC APH-TY04 (2 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 38 mensen en kreeg gemiddeld 4.3 sterren uit 9 reviews. Heb je een vraag over PAC APH-TY04 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Speaker Connection Harness for Select

Toyota and Lexus Vehicles with Factory Ampliers

Equipped with a 10-Pin and 12-Pin Connector

APH-TY04

C

Page 1

Copyright © 2019. All rights reserved. PAC is a Power Brand of AAMP Global.

PAC-audio.com

Rev: V1

Date: 010419

Introduction and Features

The APH-TY04 simplies speaker wire connections when adding aftermarket ampliers. Aftermarket ampliers can

be easily added with no need to cut or modify a vehicle’s original wiring. Each pair of wires has been labeled with the

corresponding speaker name.

Wiring Overview

Installation Notes

1. It is always best to use a tone generator (PAC part number: TL-PTG2) to verify that the tables in this manual, and the labels

on the wires, match the wiring in your specic vehicle. This is important as there are instances where different trim levels of

the factory system may have the speaker outputs in different locations.

2. Any factory amplier connectors other than the 10-pin and 12-pin connectors used by the APH-TY04, must remain

connected to the factory amplier when using a PAC AmpPRO Interface.The PAC AmpPRO Interface will not operate

properly without them connected.

3. Not all applicable vehicles will come equipped with a corresponding speaker for all of the wires populated in our harness. It

is important to understand which speakers are equipped in your vehicle.

4. If you are leaving any of the factory speakers connected to the factory amplier, simply connect the speaker wires (color for

color) between the male and female connectors, for the speakers that will be powered by the factory amplier. For example:

If you want the rear speakers to be powered by the factory amplier, simply connect the Green, Green / Black, Purple and

Purple / Black wires from the male connector to the Green, Green / Black, Purple and Purple / Black wires from the female

connector.

5. For vehicles that lose audio output when there is no load on the speaker outputs of the factory amplier, PAC load resistors

will be required (PAC Part Number LR335 or LR475).

1. Locate the vehicle’s factory amplier and disconnect the 10-pin and 12-pin connectors.

2. Connect the APH-TY04 harnesses to the connectors that were disconnected in the previous step.

3. Connect the male connectors from the APH-TY04 to the amplier.

4. Connect the longer loose wires from the APH-TY04, to your aftermarket amplier outputs or passive crossovers, according

to the tables in this manual.

5. Insulate unused wires in the 10-pin and 12-pin connectors that plug into the factory amplier side of the APH-TY04.

Installation Steps

Insulate any unused wires

Blue / BlackBlue

Red

GreeRedn /

Yellow / Red

1

610

7

ReBlackd /

Brown

GreeWhiten /

YelloBluew /

BrowBlackn /

APH-TY04-HAR 10P A

6

1

10

7

YelloBluew /

Yello

w / Red

GreeRedn /

Red

Blue

GreeWhiten /

BrowBlackn /

ReBlackd /

Blue /k Blac

Brown

APH-TY04-HAR 10P

B

1

Blue / BlackSubwoofer 2 -

7

BlueSubwoofer 2 +

2

Red / BlackSubwoofer 1 -

8

RedSubwoofer 1 +

3

Brown / BlackSpeaker 3 -

4

BrownSpeaker 3 +

5

Green / WhiteSpeaker 1 -

9

Green / Red Speaker 1 +

6

Yellow / BlueSpeaker 2 -

10

Yellow / RedSpeaker 2 +

Speaker 2

Subwoofer 2

Subwoofer 1

Speaker 3

Speaker 1

Pin NumberWire ColorWires DescriptionLabel

APH-TY04 10-Pin Connector

Connect to aftermarket amplier

output or passive crossover.

Product specificaties