PAC RadioPRO 3 RP3-GM12 Handleiding

PAC Niet gecategoriseerd RadioPRO 3 RP3-GM12

Lees hieronder de 📖 handleiding in het Nederlandse voor PAC RadioPRO 3 RP3-GM12 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 22 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
RP3-GM12
Radio Replacement Interface for General Motors Vehicles
Pacifi c Accessory Corporation® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2013 Pacifi c Accessory Corporation
www.pac-audio.com
Rev. 11-22-13
P ifi A C ti
3
3
3
Introduction & Features
Wiring Connection Chart
Illustration / Schematic
The RP3-GM12 interface allows the replacement of a factory radio in select General Motors vehicles with Class II radios. Using
this interface will retain factory features such as Warning Chimes when the original radio is removed. The RP3-GM12 provides
data bus driven outputs such as retained accessory power (RAP), vehicle speed sensor (VSS), illumination, reverse trigger and
parking brake. The RP3-GM12 also provides a secondary output for adding an optional PAC Steering Wheel Control (SWC)
retention interface (SWI-RC, SWI-PS, SWI-JACK, SWI-ECL2 or SWI-X).
Red / White Parking Brake
Output (-)*
Purple / White Vehicle Speed
Output*
Blue / White Amp Turn On Input
Red Accessory Output
(10 amp)
Orange / White Illumination Output
(+)*
Green Reverse Output (+)*
Interface Connector
Yellow Battery +12v
Black Ground
Blue Antenna On Input
White Front L + input
White / Black Front L - input
Grey Front R + input
Grey / Black Front R - input
Green Rear L + input
Green / Black Rear L - input
Purple Rear R + input
Purple / Black Rear R - input
Vehicle Connector
*Not all radios will have these
connections. Please insulate
these wires when not used.
Chime Volume Adjustment
Aftermarket Radio
Connections
Connect to SWC
Interface. Program
for Version 2.
To optional SWC interface
To Vehicle
Connector Acc On
LED
Important Notes
1. For BOSE systems, the recommended line level input is between 2-4 volts from the aftermarket radio.
2. To prevent over driven audio when installing into a vehicle with a BOSE system and the aftermarket radio does not have low
level outputs then an LOC (part # SOEM-4 or LP3-4) is recommended to match the input voltage.
3. Use the 4 position selector switch located on the side of the interface to select the best chime output for your specifi c installation.
RP3-GM12
Radio Replacement Interface for General Motors Vehicles
Pacifi c Accessory Corporation
® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2013 Pacifi c Accessory Corporation
www.pac-audio.com
P ifi A C ti
Rev. 11-22-13
3
3
3
Steering Wheel Control Output Connector
Testing & Verifi cation
Product Updates (Firmware)
1. The RP3 provides a SWC output connector attached
to the harness. For ease of installation, all necessary
connections for an SWI have been made for you.
2. When using this SWC output connector the SWC
interface must be programmed for version 2 .
(refer to SWC interface programming instructions for
exact programming sequence).
3. Both loops should remain in tact.
4. During steering wheel button assignment programming
the vehicle should be running and each button should
be pressed and held for at least 5 seconds. Please refer
to the SWI manual for button assignment order.
1. Turn the ignition on. The LED on the interface will turn on & the +12v accessory wire will turn on.
2. Turn on the radio & check balance & fade.
3. Verify that the factory subwoofer (if present) is playing
4. If an optional SWC retention interface was used, verify that all SWC are functioning properly.
5. Turn off vehicle & remove key. RAP will be active & keep the radio on for 10 minutes or until the drivers door is opened.
6. The LED & radio will turn off when RAP turns off or the drivers door is opened.
7. Use the 4 position selector switch located on the side of the interface to select the best chime output volume for your specifi c
installation. Setting 1 being loudest and 4 softest.
The RP3-GM12 can be updated with new fi rmware as it becomes available using the PAC-UP interface updater (sold separately).
Please visit www.pac-audio.com/fi rmware for available updates.
Chime Volume Adjustment
1
4
2
3
Installation Steps
1. It is extremely important to makes sure the ignition is off and the drivers door open before connecting the interface to the vehicle.
2 Make all connections as described in the chart on page 1. The audio level will vary depending on the new radios pre-amp output
voltage (2-4 volts is recommended).
3. Follow the instructions below if you wish to add an optional SWC retention interface.

Product specificaties

Merk: PAC
Categorie: Niet gecategoriseerd
Model: RadioPRO 3 RP3-GM12

Heb je hulp nodig?

Als je hulp nodig hebt met PAC RadioPRO 3 RP3-GM12 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd PAC

PAC

PAC LPHHD04 Handleiding

6 Maart 2024
PAC

PAC RP4.2-TY13 Handleiding

8 December 2023
PAC

PAC PGHGM2 Handleiding

7 Juli 2023
PAC

PAC CAM-TY12 Handleiding

6 Juli 2023
PAC

PAC VCI-NIS2 Handleiding

24 Juni 2023
PAC

PAC SNI-1/3.5 Handleiding

22 Juni 2023
PAC

PAC ANC-CH01 Handleiding

21 Juni 2023
PAC

PAC RP4-FD11 Handleiding

20 Juni 2023
PAC

PAC AP4-GM61 Handleiding

19 Juni 2023
PAC

PAC IGN-3 Handleiding

19 Juni 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Playtive

Playtive IAN 327221 Handleiding

1 Mei 2024
Samsung

Samsung UN32J4001AF Handleiding

1 Mei 2024
Bauknecht

Bauknecht KSI 18GF2 P2 Handleiding

27 April 2024
Fakir

Fakir Artemis TS 150 Handleiding

26 April 2024
Sony

Sony UTX-M03 Handleiding

26 April 2024
Sony

Sony URX-P03 Handleiding

26 April 2024
Sony

Sony WRU-806B Handleiding

26 April 2024
Sony

Sony UTX-B03 Handleiding

26 April 2024
Sony

Sony UTX-P03 Handleiding

26 April 2024
Sony

Sony ODS-L10 Handleiding

26 April 2024