Ozito HSS-5000U Handleiding

Ozito Schuurmachine HSS-5000U

Lees hieronder de 📖 handleiding in het Nederlandse voor Ozito HSS-5000U (3 pagina's) in de categorie Schuurmachine. Deze handleiding was nuttig voor 44 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/3

ORBITAL

SANDER

1/2 SHEET

ORIGINAL INSTRUCTIONS

SPECIFICATIONS

Input: 230-240V ~ 50Hz

Power: 350W

No Load Speed: 12,000 /min

Pad Shape: 1/2 Sheet

Pad Size: 230 x 115mm

Weight: 2.05kg

HSS-5000U

WHAT’S IN THE BOX

Orbital Sander

MAINTENANCE

DESCRIPTION OF SYMBOLS

TROUBLESHOOTING

V Hz

~ W

/min

Volts

Alternating current

Revolutions or

reciprocation per minute

Double insulatedWarning

Hertz

Watts

No load speed

• Keep the ventilation vents of the sander clean at all times, if possible, prevent

foreign matter from entering the vents.

• After each use, blow air through the sander housing to ensure it is free from

all dust particles which may build up. Build up of dust particles may cause the

sander to overheat and fail.

• If the enclosure of the sander requires cleaning, do not use solvents but a

moist soft cloth only. Never let any liquid get inside the sander; never immerse

any part of the sander into a liquid.

Carbon Brushes

When the carbon brushes wear out, the sander will spark and/or stop.

Discontinue use as soon as this happens. They should be replaced prior to

recommencing use of the sander. Carbon brushes are a wearing component of

the sander therefore not covered under warranty. Continuing to use the sander

when carbon brushes need to be replaced may cause permanent damage to

the sander. Carbon brushes will wear out after many uses but when the carbon

brushes need to be replaced, take the sander to an

electrician or a power tool repairer for a quick and

low cost replacement. Always replace both carbon

brushes at the same time.

Note: Ozito Industries will not be responsible for any

damage or injuries caused by the repair of the sander

by an unauthorised person or by mishandling of the

sander.

Sparking visible through the housing air vents

A small amount of sparking may be visible through the housing vents.

This is normal and does not indicate a problem.

Excessive sparking visible through the housing air vents

and/or the sander failing to operate

May indicate the carbon brushes have worn out and need to be

replaced. Carbon brushes should only be replaced by a qualied

electrician or power tool repairer.

Sandpaper Selection

Selecting the correct grit of sandpaper is an important step in achieving

optimum results. Coarse grit will remove the most material. Finer grit will

produce a smoother nish. The condition of the workpiece will determine the

grit of the sandpaper to be used. The higher the grit number, the ner the

grade of sandpaper.

If the surface is rough, start with a coarse grit and sand until the surface is

uniform. Medium grit may then be used to remove scratches left by the coarser

grit. Finer grit is then used to nish the surface. Always continue sanding with

each grade of sandpaper until the surface is uniform.

MATERIAL APPROPRIATE GRIT

Coarse Sanding Fine Sanding

Paintwork 180 400

Wood: Softwood 60 240

Hardwood 60 180

Veneer 240 320

Note: If intermediate sanding is required, choose a grit rating between coarse and

ne. The above table is intended as a guide only. To ensure a satisfactory result,

a small, inconspicuous area should rst be tested to ensure the grit of sandpaper

chosen is suitable for the desired nish.

SPARE PARTS

ozito-diy.co.uk

ORBITAL SANDER SAFETY WARNINGS

WARNING! When using mains-powered tools, basic safety precautions, including the

following, should always be followed to reduce risk of re, electric shock, personal injury

and material damage.

Read the whole manual carefully and make sure you know how to switch the tool off in an emergency, before

operating the tool.

Save these instructions and other documents supplied with this tool for future reference.

Before you connect the equipment to the mains supply make sure that the data on the rating plate are

identical to the mains data.

This tool is double insulated therefore no earth wire is required.

If the supply cord is damaged, it must be replaced by an electrician or a power tool repairer in order to avoid

a hazard.

Note: Double insulation does not take the place of normal safety precautions when operating this tool. The

insulation system is for added protection against injury resulting from a possible electrical insulation failure

within the tool.

Using an Extension Lead

Always use an approved extension lead suitable for the power input of this tool. Before use, inspect the

extension lead for signs of damage, wear and ageing. Replace the extension lead if damaged or defective.

When using an extension lead on a reel, always unwind the lead completely. Use of an extension lead not

suitable for the power input of the tool or which is damaged or defective may result in a risk of re and electric

shock.

WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and

instructions may result in electric shock, re and/or serious injury.

Save all warnings and instructions for future reference. The term “power tool” in the warnings refers

to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

1. Work area safety

a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.

b. Do not operate power tools in explosive atmospheres, such as in the presence of ammable

liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

c. Keep children and bystanders away while operating a power tool. Distractions can cause you to

lose control.

2. Electrical safety

a. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power tools. Unmodied plugs and matching outlets will

reduce risk of electric shock.

b. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the

risk of electric shock.

d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase

the risk of electric shock.

e. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of electric shock.

f. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of electric shock.

3. Personal safety

a. Stay alert, watch what you are doing and use common sense when operating a power tool. Do

not use a power tool while you are tired or under the inuence of drugs, alcohol or medication. A

moment of inattention while operating power tools may result in serious personal injury.

b. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce

personal injuries.

c. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to

power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your

nger on the switch or energising power tools that have the switch on invites accidents.

d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result in personal injury.

e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the

power tool in unexpected situations.

f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

g. If devices are provided for the connection of dust extraction and collection facilities, ensure

these are connected and properly used. Use of dust collection can reduce dust-related hazards.

4. Power tool use and care

a. Do not force the power tool. Use the correct power tool for your application. The correct power tool

will do the job better and safer at the rate for which it was designed.

b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be repaired.

c. Disconnect the plug from the power source and/or the battery pack from the power tool before

making any adjustments, changing accessories, or storing power tools. Such preventive safety

measures reduce the risk of starting the power tool accidentally.

d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the

power tool or these instructions to operate the power tool. Power tools are dangerous in the hands

of untrained users.

e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and

any other condition that may affect the power tool’s operation. If damaged, have the power tool

repaired before use. Many accidents are caused by poorly maintained power tools.

f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking

into account the working conditions and the work to be performed. Use of the power tool for

operations different from those intended could result in a hazardous situation.

5. Service

a. Have your power tool serviced by a qualied repair person using only identical replacement

parts. This will ensure that the safety of the power tool is maintained.

GENERAL POWER TOOL SAFETY WARNINGS - PERSONAL SAFETY

ELECTRICAL SAFETY

WARNING!

• Hold power tool by insulated gripping surfaces, because the sanding pad

may contact its own cord. Cutting a “live” wire may make exposed metal parts of

the power tool “live” and could give the operator an electric shock.

Recommendation that the tool always be supplied via a residual current device

with a rated residual current of 30 mA or less.

Unplug the sander before changing accessories. Accidental start-ups may occur if

the sander is plugged in while changing an accessory.

Disposing of dust. Be extremely careful of dust disposal, materials in ne particle

form may be explosive. Do not throw sanding dust on an open re. Spontaneous

combustion, may in time, result from a mixture of oil or water with dust particles.

Always wear eye protection and a dust mask for dusty applications and when

sanding overhead. Sanding particles can be absorbed by your eyes and inhaled

easily and may cause health complications.

Use special precautions when sanding chemically pressure treated timber,

paint that may be lead based, or any other materials that may contain

carcinogens. A suitable breathing respirator and protective clothing must be worn

by all persons entering the work area. Work should be sealed by plastic sheeting and

persons not protected should be kept out until work area is thoroughly cleaned.

Do not ‘wet sand’ with this sander. Liquids entering the motor housing are an

electrical shock hazard.

Do not use sandpaper intended for larger sanding pads. Larger sandpaper will

extend beyond the sanding pad causing snagging, tearing of the paper or kick-back.

Extra paper extending beyond the sanding pad can also cause serious lacerations.

WARNING!

Some dust created by power sanding, sawing, grinding, drilling and other

construction activities contain chemicals known to cause cancer, birth defects or other

reproductive harm.

Some examples of these chemicals are:

• Lead from lead-based paints;

• Crystalline silica from bricks, cement and other masonry products, and;

• Arsenic and chromium from chemically-treated timber.

Your risk from these exposures varies, depending on how often you do this type of

work. To reduce your exposure to these chemicals: work in a well ventilated area and

work with approved safety equipment, such as dust masks that are specially designed

to lter out microscopic particles.

Read instruction manual

Sanding Sheet x 3

WARRANTY

OZITO UK Unit 9 Stadium Court, Wirral International Business Park, Plantation Road, Bromborough, Wirral, CH62 3QG 0716

All of our products undergo strict quality checks to ensure that they reach

you in perfect condition. In the unlikely event that your device develops a

fault, please contact our service department at the address shown on this

guarantee card. You can also contact us by telephone using the customer

service number shown. Please note the following terms under which

guarantee claims can be made:

1. These warranty terms regulate additional warranty services, which the

manufacturer mentioned below promises to buyers of its new products

in addition to their statutory guarantee claims are not affected by this

guarantee. Our guarantee is free of charge to you.

2. The warranty services only covers defects due to material or

manufacturing faults on a product which you have bought from the

manufacturer mentioned below are limited to either the rectication of said

defects on the product or the replacement of the product, whichever we

prefer.

Please note that our devices are not designed for use in commercial, trade

or professional applications. A guarantee contract will not be created if the

device has been used by commercial, trade or industrial business or has

been exposed to similar stresses during the guarantee period.

3. The following are not covered by our guarantee:

- Damage to the device caused by a failure to follow the assembly

instructions or due to incorrect installation, a failure to follow the operating

instructions (for example connecting it to an incorrect mains voltage or

current type) or a failure to follow the maintenance and safety instructions

or by exposing the device to abnormal environmental conditions or by lack

of care and maintenance.

- Damage to the device caused by abuse or incorrect use (for example

overloading the device or the use or unapproved tools or accessories),

ingress of foreign bodies into the device (such as sand, stones or dust,

transport damage), the use of force or damage caused by external forces

(for example by dropping it).

- Damage to the device or parts of the device caused by normal or natural

wear or tear or by normal use of the device.

4. Your Product is guaranteed for a period of 36 months from the original

date of purchase and is intended for DIY (Do It Yourself) use only. Lithium

Ion batteries and chargers are covered by a 12 month warranty. Warranty

excludes consumable parts. Guarantee claims should be submitted

before the end of the guarantee period within two weeks of the defect

being noticed. No guarantee claims will be accepted after the end of the

guarantee period. The original guarantee period remains applicable to the

device even if repairs are carried out or parts are replaced. In such cases,

the work performed or parts tted will not result in an extension of the

guarantee period, and no new guarantee will become active for the work

performed or parts tted. This also applies if an on-site service is used.

IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST

RETURN THE PRODUCT TO THE PLACE OF PURCHASE WITH YOUR

Please refer to the restrictions of this warranty concerning wearing parts,

consumables and missing parts as set out in the service information in

these operating instructions.

CUSTOMER SERVICE HELPLINE

GB: 0151 294 4488

IRL: 1850 882711

Ozito-diy.co.uk

Spare parts can be ordered from the Special Orders Desk

at your local Bunnings Warehouse or Homebase store.

For further information, or any parts visit

www.ozito-diy.co.uk or contact Ozito Customer Service:

Great Britain: 0151 294 4488

Ireland: 1850 882711

E-mail: enquires@ozito-diy.co.uk

ONLINE MANUAL

Scan this QR Code with your

mobile device to take you to

the online manual.

1 Front Handle

2 Metal Base Plate

3 Spring Clamp

4 On/Off Switch

5 Rear Handle

6 Dust Canister

ORBITAL SANDER

KNOW YOUR PRODUCT

HSS-5000U

1. ATTACHING SANDPAPER 2. DUST CANISTER 3. CONTROLS 4.

SANDING

5. TIPS

SETUP & PREPARATION OPERATION

Ensure the tool is disconnected from the power supply

before performing any of the following operations.

2. Fold the sandpaper to match the contours of the sanding pad.

1. Unlock the spring clamp on both sides of the sander.

4. Feed the paper under

the paper clip at the rear

of the sander. Lock the

clamp.

3. Feed the paper under

the paper clip at the

front of the sander. Lock

the clamp.

Note: Ensure the sanding sheet is rmly clamped and held at

against the base of the sanding pad.

1/3 Full

2. To remove, pull

the dust canister

away from the dust

extraction port.

1. Push the dust

canister onto the

dust extraction port

until it clicks into

place.

Install

3. Regularly check the dust canister and empty when it becomes

1/3 full for optimum dust extraction.

Remove

Empty

The tool is recommended for use with a residual current

device with a rated residual current of 30mA or less.

2. To turn the sander off, slide the switch back.

2. To turn the sander on, slide the switch forward.

1. Connect the tool to the mains power supply.

CAUTION: GUIDE THE CORD DURING SANDING TO

PREVENT IT BEING CAUGHT ON THE WORKPIECE,

OR OTHER OBJECTS.

1. Secure the material to be sanded.

2. Firmly grasp the sander. Turn it on and let the motor build up to

maximum speed. Gradually lower it onto the workpiece using a

forward movement.

3. For optimum results, use backward and forward strokes.

Note: Keep the entire sanding pad in contact with the workpiece at

all times during sanding.

• Never force the sander. The weight of the sander supplies

adequate pressure, allowing the sandpaper to do the work.

Applying additional pressure will slow the motor, rapidly wear

the sandpaper, and greatly reduce the sander speed. This will

slow the removal rate and produce an inferior quality surface.

CAUTION: Excessive pressure will overload the motor, causing

possible damage to the sander by overheating the motor; or

damage to the workpiece.

• Check your workpiece often. The sander is capable of

removing material rapidly, especially with coarse paper.

• The orbital action of your sander allows you to sand with the

grain, or at any angle across it for most sanding jobs. In the

nal stages a better nish will be achieved by sanding with

the grain.

• Do not sand on one spot for too long. The sader’s rapid

action may remove too much material, creating an uneven

surface.

7 Sandpaper x 3 (60 / 80/ 120 Grit)

ACCESSORIES

Product specificaties

Merk:	Ozito
Categorie:	Schuurmachine
Model:	HSS-5000U

Heb je hulp nodig?

Als je hulp nodig hebt met Ozito HSS-5000U stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Schuurmachine Ozito

Ozito BSR-7000U Handleiding

16 Maart 2024

Ozito PXMSS-700U Handleiding

16 Maart 2024

Ozito TSS-3100U Handleiding

25 Juni 2023

Ozito HSS-5000U Handleiding

20 Juni 2023

Ozito QSS-1000U Handleiding

17 Juni 2023

Ozito ROS-2000U Handleiding

17 Juni 2023

Ozito ROS-4000U Handleiding

15 Juni 2023

Ozito DSR-2500U Handleiding

12 Juni 2023

Ozito MSK-001U Handleiding

11 Juni 2023

Ozito DSR-2100U Handleiding

6 Juni 2023

Handleiding Schuurmachine

Nieuwste handleidingen voor Schuurmachine

Duro Pro D-NTS 156 Handleiding

18 April 2024

Bavaria By Einhell BES 125 E Handleiding

9 April 2024

Bavaria By Einhell BBS 850 E Handleiding

9 April 2024

Bavaria By Einhell BSS 280 Handleiding

9 April 2024

Bavaria By Einhell BBS 1200 Handleiding

9 April 2024

Bavaria By Einhell BSS 105 Handleiding

9 April 2024

Einhell Bavaria BSS 105 Handleiding

25 Maart 2024

Einhell Bavaria BBS 1200 Handleiding

25 Maart 2024

Einhell Bavaria BSS 280 Handleiding

25 Maart 2024

Einhell Bavaria BBS 850 E Handleiding

25 Maart 2024