Ozito CPP-802 Handleiding

Bekijk gratis de handleiding van Ozito CPP-802 (8 pagina’s), behorend tot de categorie Pomp. Deze gids werd als nuttig beoordeeld door 23 mensen en kreeg gemiddeld 4.0 sterren uit 2 reviews. Heb je een vraag over Ozito CPP-802 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

7. Recommended Setup

Cleaning

Use a moist cloth to wipe down the pump housing. Allow to dry

thoroughly before storing in a dry location that is protected from bad

weather conditions.

Storage

If there is danger of frost, dismantle the device and accessories, clean

and store them in a place protected from frost.

Dismantle and store

1. Disconnect the device from the mains

supply.

2. Fully open any shut-off mechanisms

(spray nozzles, valves, etc.) in the

pressure line so that the air can escape

without obstruction.

3. Completely empty the pump by

unscrewing the water drain plug.

4. Dismantle the suction and pressure lines

from the device.

5. Store device in a frost-free room

(at least 5 °C).

WARNING! MAKE SURE THE PUMP IS DISCONNECTED

FROM ELECTRIC POWER SUPPLY BEFORE

PERFORMING MAINTENANCE PROCEDURES.

WARNING! THE INPUT HOSE OR PIPE SHOULD BE

LOW ENOUGH IN THE WATER TO ENSURE THAT IF

THE WATER LEVEL FALLS, THE PUMP WILL NOT RUN DRY.

ENSURE THAT THIS IS CHECKED WHEN IN OPERATION.

WARNING! MAKE SURE THAT THE DEVICE AND

CONNECTED ACCESSORIES ARE DEPRESSURIZED

BEFORE CARRYING OUT ANY WORK ON THE DEVICE.

Positioning the hose or pipe

Position the input hose or pipe so that it rises from the water drawing

source to the pump. Where possible, avoid positioning the input hose

or pipe higher than the pump, as this would delay the escape of air

bubbles from the input hose or pipe and impede the priming process

(see section ‘’ for description on priming the pump)Priming the pump

• Thesuctionlineshouldbeasshortaspossible,sincetheconveying

capacity decreases as the length of the line increases.

Note:A leaking hose or pipe will draw in air and therefore not draw in

any water.

Note:A non-return valve is recommended so that the water does not

run off when the pump is shut off.

Note:Asuctionin-linelterwitha3000l/hourminowrate,and150to

250micronmeshmustbeusedtoprotectthepumpfromsand,dirtetc.

TheOzitoPAPF-001Pre-lterorequivalentisavailablefromBunnings

stores.

Note: During the initial set-up, please purge all air from the system via

the discharge outlet highest in the system.

INSTALLATION

Recommended set-up

Connection with tank base below water pump

Connection with tank base level with water pump

Connection with tank base above water pump

F EIRM BAS

SOLID STRUCTURE

0

1

2

3

4

5

6Bar

WATERTANK

NON-RETURN

VALVE

DISCHARGE

OUTLET

GATE

VALVE

SUCTION LINE

150mm 150mm

UNION

COUPLING

depending on

installation

IN-LINE

FILTER

WATERTANK

GATE

VALVE

SUCTION LINE

150mm

F EIRM BAS

SOLID STRUCTURE

0

1

2

3

4

5

6Bar

DISCHARGE

OUTLET

150mm

UNION

COUPLING

depending on

installation

IN-LINE

FILTER

0

1

2

3

4

5

6Bar

150mm 150mm

WATERTANK

GATE

VALVE

SUCTION LINE

SOLID STRUCTURE

DISCHARGE

OUTLET

F EIRM BAS

UNION

COUPLING

depending on

installation

IN-LINE

FILTER

WARNING! TO ENSURE CORRECT PUMP OPERATION

IT IS ESSENTIAL THAT A SUCTION IN-LINE FILTER BE

USED FOR A CLEAN WATER SUPPLY.

MAINTENANCE

Product specificaties