Optex CX-702RS Handleiding
Optex
Niet gecategoriseerd
CX-702RS
Bekijk gratis de handleiding van Optex CX-702RS (4 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 2 mensen en kreeg gemiddeld 5.0 sterren uit 1.5 reviews. Heb je een vraag over Optex CX-702RS of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/4
PASSIVE INFRARED DETECTOR
CX-702RS , CX-702S
No.59-0974-3 0708-30
BATTERY OPERATED (CE) Form C Relay
(CX-702RS Only)
FEATURES
Selectable ”WIDE ANGLE” and “LONG RANGE”
detection patterns.
Double Conductive Shielding of the pyroelectric
element - Extremely High Light.
Multifocus Optics Design (Patent listed)
Sealed Optics
Easy Installation
CX-702RS Only
Low Current Draw : 5µA (Normal. In Standby)
Battery Oparated
Form C Alarm Output and Tamper Switch
OPTION
CA-1W : Wall Mount Bracket ; Adjustable ±45°(Horizontally), 0-20°(Vertically downwards)
CA-2C : Ceiling Bracket ; Adjustable ±45°(Horizontally), 0-20°(Vertically downwards)
BA-70 : Backbox for wireless transmitter
CX-702S Only
Form C Alarm Output Relay
LED On/Off Switch
1.INSTALLATION HINTS
1
Avoid direct sunlight.
2
Avoid mounting detector where
movement of Fans or Air
Conditioning Fans can be detected.
3
Avoid vapor or high humidity
that can cause condensation.
4
Avoid blocking detection area
with curtain, screen, etc.
5
Do not install in the outdoors.
6
WARNING
Never repair or modify
product. It may cause
accident, fire hazard or
electric shock.
7
WARNING
When damage has occured to the
product, i.e. water logged, abnormal
things inside product, overheating or
smoking, strange smells etc.,
immediately stop using product and contact your supplier.
Otherwise, continued use in such condition may cause
electric shock or fire hazard.
8
CAUTION
Mount securely.
Fall of A product
may cause injury.
2.DETECTION AREA
●
●
●
●
●
●
●
●
●
**ATTENTION**
The specified detection area can be achieved by mounting the unit at a height of 2.4m. Mounting at a lower or higher height may reduce the area of coverage.
●
1
2 3
4
5
6
3.DESCRIPTION AND OPERATION
4.INSTALLATION
Loosen fastening screw
and remove cover.
For wiring, put the point of screw-
driver in wiring knockouts of base,
and hit the top of dirver to crack into
knockouts. Lead in wires through
knockouts along the wiring guide on
the rear side of base. Mount base
with supplied screws. When using a
bracket, check matching knockout
position before opening mounting
holes.Wire according to Section 5.
When you remove the PCB, push down
on the hook under PCB and remove it from
its base. Attachment of PCB is the reverse
of removal. Do not remove PCB from base
of CX-702RS.
Release hook at cover.
Then remove lens holder
from cover.
Remove lens holder carefully.
Select wide angle or long range
according to Section 6-2. (Note:
Factory default is wide area)
Check to confirm that the lens is in
the desires position.Press down the
lens holder until it clicks into place
along the guide of cover.
Conduct a walktest and
make adjustments
(Section 7). Fit cover
using fastening screw.
Guides of Cover
Guides of Lens Holder
TAMPER
(Form C)
ALARM OUTPUT
(Form C)
POWER INPUT
(Use 3 - 9V
Alkaline or
Lithium Battery)
ALARM OUTPUT
(Form C)
POWER INPUT
(9.5 - 16 VDC)
Power wires should not exceed
the following lengths.
When using two or more units on one wire, the
maximum length is obtained by dividing the
maximum wire length listed above by the
number of units used.
W IR ESIZE 12V 14V
990ft 2150ft
(300m ) (650m )
1560ft 3390ft
(470m ) (1030m )
2500ft 5410ft
(760m ) (1650m )
C X‑702S
A W G 22(0.33m m
2
)
A W G 20(0.52m m
2
)
A W G 18(0.83m m
2
)
Cover
LED Indicator
Lens
Cover Fastening Screw
Base
CX-702RS
CX-702S
Battery Space
Terminals
Tamper switch
Sensor
Do not touch.
Terminals
Sensor
Do not touch.
Wiring Knockout
Mounting Knockout
Pitch 3.29 inch (83.5mm)
Corner mount Knockout
Wiring Knockout
Mounting Knockout
Pitch 3.29 inch (83.5mm)
Corner mount Knockout
Double Conductive Shield
Do not touch.
Lens Holder
Connect tamper terminals to
a 24 hour supervisory loop.
[
]
CX-702RS CX-702S
− ＋
− ＋
5.WIRING
6.ADJUSTMENTS FOR REQUIRED AREA PATTERN
The CX-702 is designed to provide ideal detection areas for different patterns ranging from 40ft.(12m) to 70ft.(21m) Wide Angle,
and 80ft.(24m) to 150ft.(45m) Long Range.
The following adjustments will provide ideal detection areas for each of these requirements.
1. DETERMINE THE AREA PATTERN
Before making adjustments, determine the area pattern - detection range mounting height.
2.SELECTING WIDE ANGLE OR LONG RANGE DETECTION
1. Inverting the lens will select either the Wide Angle or Long Range detection patterns.
2. Please note markings “W(Wide Angle)” and
“L(Long Range)”, on each side of lens.
3. For Wide Angle, “W” will be on top of lens.
4. For Long Range, “L” will be on top of lens.
3.VERTICAL ADJUSTMENT OF DETECTION AREA
Adjust the vertical angle according to the desired detection range and mounting height.
1. Set the upper edge of the lens at
either the “A”, “B” or “C” position.
2. The following chart illustrates the
different position setting.
3. Confirm the detection area by
conducting a walktest.
7.FUNCTIONS
40 (12) 50 (15) 60 (18) 70 (21) 80 (24)
100
(30)
120
(36)
150
(45)
6 (1.8)
B A A A
6 (1.8)
B B A A
8 (2.4)
C C C C
8 (2.4)
C C C C
12 (3.6)
C C C C
12 (3.6)
C C C C
DISTANCE
HEIGH
T
W : WIDE ANGLE L : LONG RANGE
HEIGHT
DISTANCE
ft.(m)
Always conduct a walktest after
changing the position of this
switch to ensure the detector is
still providing optimum coverage.
CX-702RS
CX-702S
LED ON / OFF Switch
Pulse Count
Selector (2 / 4)
Walk Test Switch
(Must be OFF for normal operation)
CAUTION!
1. LED ON / OFF (CX-702S Only)
The Alarm LED indicator can be switched either “ON” or “OFF”
ON
OFF
2. PULSE COUNT
The Detection Mode can be switched to either “2” or “4” mode
depending on the environmental conditions of the installation.
2 : For normal applications.
4 : For use in hostile areas where there may be movement of small animals or
other objects such as fax machines or curtains.
When the “4” is selected, the detector’s sensitivity may seem sluggish. It is therefore important to always
conduct a walktest to ensure that the desired coverage is given.
3. WALK TEST SWITCH (CX-702RS Only)
WALK TEST
1) LED lights up when the unit has detected.
2) An alarm signal is outputted whenever it detects.
NORMAL : Normal Operation (Battery Saving Mode)
1) LED does not light up even though the unit detects.
2) The succeeding signals are not outputted even though it detects within 2 minutes
after the first alarm is outputted. This is in order to save the battery consumption.
2
4
WALK TES
NORMAL
CAUTION!
Do not use pulse
count 4 for Long
Range detection.
Product specificaties
| Merk: | Optex |
| Categorie: | Niet gecategoriseerd |
| Model: | CX-702RS |
Heb je hulp nodig?
Als je hulp nodig hebt met Optex CX-702RS stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd Optex
16 Juni 2025
21 December 2024
5 December 2024
5 December 2024
5 December 2024
5 December 2024
5 December 2024
5 December 2024
23 September 2024
5 Augustus 2024
Handleiding Niet gecategoriseerd
- Laplink
- GolfBuddy
- Tiptop Audio
- Elight
- Enerdrive
- Heller
- Ikan
- Mercyu
- Neunaber
- Altronix
- Bavaria
- Europalms
- Nuance
- Flycam
- Newland
Nieuwste handleidingen voor Niet gecategoriseerd
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025