Oliveri FT3EGN Handleiding
Pagina's 2 Kraan
Bekijk de handleiding van Oliveri FT3EGN gratis online of download de PDF. Deze handleiding is 1 keer bekeken. Vraag over dit model? Stel een vraag
Before attempting any work involving mains water supply lines,
ensure the water supply is shut off.
Stop valves (preferably with filters) must be used when installing
your Oliveri mixer to allow isolation. (not supplied with mixer).
Failure to do so where required will void warranty.
This mixer tap is already pre-assembled and tested. Do not
disassemble, as this may void the warranty.
This mixer tap must be installed in accordance with these
instructions.
MAX OPERATING PRESSURE: ..............................................................6 bar (600kPa)
RECOMMENDED OPERATION PRESSURE: ..........................................1.5-5 bar (150-500kPa)
MAX HOT WATER TEMPERATURE: .....................................................80°C
RECOMMENDED HOT WATER TEMPERATURE: ..................................60°C
3 in 1 Filtered Water Mixer Tap
FT3ESQFT3EGN
Where water pressure exceeds 600kPa, a pressure reducing device is required to be installed. Note that
water pressure overnight can reach 150% of the daytime pressure.
CARE & MAINTENANCE
Unscrew and clean the spout aerator periodically - especially if you notice a drop in water pressure.
The polished chrome plate finish on your Oliveri mixer tap will resist stains and dirt build up.
Clean with a soft cloth and warm soapy water as necessary - rinse and dry after cleaning. Avoid using abrasive
or acid based cleaning products.
THIS MIXER TAP MUST BE INSTALLED BY A LICENSED PLUMBER IN
ACCORDANCE WITH LOCAL REGULATIONS
This Oliveri tap is manufactured to standard AS/NZS 3718.
Note: Installation of aerators containing flow regulators.
Upon re-installation of the aerator after flushing, the aerator should be tightened with aerator key
supplied to prevent removal by hand.
Note: Ceramic Cartidges - Warranty claims will not be honoured where the ceramic cartridge has
malfunctioned due the the presence in the water supply of;
- Copper tube pieces, sand, dirt or stones
- Thread tape
- Other objects not normally present in potable water supplies.
- Do not remove the cartridge from the body as it has been pressure tested and tightened to a
specific torque.
TF165b - FT3EGN FT3ESQ installation instructions
Technical Data
Installation Instructions
WARRANTY
This mixer tap is warranted to be free from manufacturing defects for a period of 1 year replacement parts &
labour.
Where a genuine manufacturing defect arises within the warranty period Oliveri will, at its election, repair
the defect or replace the product subject to the terms contained in the full warranty information available
at https://oliveri.com.au/service-and-warranty.
This warranty does not cover against normal wear and will be voided if the product is misused or not
installed in accordance with these instructions.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are
entitled to a replacement or refund for a major failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to
be of acceptable quality and the failure does not amount to a major failure.
SERVICE
If the product represents a danger, or damage to property may occur, immediately shut off the water supply.
If the product requires servicing, please contact your installer (preferably the one who installed it).
If the Plumber / Installer is satisfied that the problem is not due to poor installation, contact Oliveri’s
nominated Warranty Service Agent for assistance on:
Ph: (08) 8348 6444 (choose the after sales service and warranty option)
Email: [email protected]
For full warranty information visit: https://oliveri.com.au/service-and-warranty
If a warranty service call finds that the spout does not have a genuine manufacturing fault, our Warranty
Service Agent reserves the right to pass on any call-out fee to the householder.
Installation Instructions
BODY ASSEMBLY STYLE
FOR ILLUSTRATION ONLY
MAY VARY
INSTALLATION
Note - before installation see [Fig.1] for basin / bench requirements.
1. Ensure the supply lines are fluhed before connecting the Mixer.
2.Fit the body assembly to the basin ensuring the base washer is correctly positioned underneath the
base ring.
3.(Under the basin / bench) Fit the steel washer, then screw the locking screw onto the threaded sleeve.
Use the philips head screws to further tighten the nut.
4. Connect the flexible hoses to the supply lines, making sure the hot water is connected to the hot water
hose.
5.Prior to introducing the mains water supply, open the handle in the mixed position, midway between
full hot and full cold.
TF165 - FT3EGN FT3ESQ installation instructionsb
Product specificaties
| Merk: | Oliveri |
| Categorie: | Kraan |
| Model: | FT3EGN |
Heb je hulp nodig?
Als je hulp nodig hebt met Oliveri FT3EGN stel dan hieronder een vraag en andere gebruikers zullen je antwoorden