Noctua NH-U12S TR4-SP3 Handleiding

Noctua Hardwarekoeling NH-U12S TR4-SP3

Bekijk gratis de handleiding van Noctua NH-U12S TR4-SP3 (3 pagina’s), behorend tot de categorie Hardwarekoeling. Deze gids werd als nuttig beoordeeld door 37 mensen en kreeg gemiddeld 4.8 sterren uit 19 reviews. Heb je een vraag over Noctua NH-U12S TR4-SP3 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Download PDF

Pagina 1/3

Required mounting parts:

Dear customer,

Congratulations on choosing the Noctua NH-U12S TR4-SP3.

Continuing the legacy of Noctua’s classic NH-U-series, which has

received more than a thousand awards and recommendations from

international hardware websites and magazines, the NH-U12S has

become a benchmark for slim, highly compatible 120mm single

tower coolers. The TR4-SP3 version is a tailored custom model for

AMD’s TR4/SP3 platform and features a larger contact surface

as well as the latest SecuFirm2™ mounting system for socket

TR4/SP3.

Enjoy your NH-U12S TR4-SP3!

Yours sincerely,

Roland Mossig, Noctua CEO

This manual will guide you through the installation process of the

SecuFirm2™ mounting system step by step.

Prior to installing the cooler, please consult the compatibility list

on our website (www.noctua.at/compatibility) and verify that

the cooler is fully compatible with your motherboard.

Please also make sure that your PC case offers sufficient clear-

ance for the cooler and that there are no compatibility issues

with any other components (e.g. tall RAM modules). Double

check that the heatsink and fan clips do not make contact with

the VGA card or other PCIe cards.

Noctua cannot be held responsible for any damage or losses

caused by compatibility issues.

Should you encounter any difficulties, please check the FAQs on

our website (www.noctua.at/faqs) and don’t hesitate to contact

our support team at support@noctua.at.

Multilingual versions of this manual are available on our website:

www.noctua.at/manuals

Offsetting the cooler to increase PCIe clearance

If you would like to use a PCIe card in the top slot and the slot is

located close to the CPU socket on your motherboard, test fit the

cooler to the CPU socket in order to check if it comes too close

to the back side of the card or overhangs the slot. If yes, you

can offset the cooler towards the top side of the motherboard by

either 3mm or 6mm for increased PCIe clearance.

Step 1

NM-SMT3 mounting toolNM-AFB7 fastening brackets

(pre-installed on the cooler)

Noctua NH-U12S |

Installation Manual | TR4-SP3

TR4-SP3

In order to offset the cooler, please unscrew the NM-AFB7 fasten-

ing brackets and re-install them in the +3 (3mm offset) or +6

(6mm offset) position.

Caution: Gently tighten the screws until they stop, but don’t use

excessive force (max. torque 0.6 Nm).

+ 0mm offset

+ 3mm offset

+ 6mm offset

Noctua NH-U12S |

Installation Manual | TR4-SP3

TR4-SP3

Connect the fan to the motherboard’s CPU fan header.

Depending on your CPU and the temperature inside the case, you

may interconnect the supplied NA-RC6 Low-Noise Adapter (L.N.A.)

in order to further reduce the fan’s operating noise.

Applying thermal paste

If there are residual traces of thermal paste or thermal pads on

your CPU, please clean them off first.

Then press 9 small drops (3-4mm diameter) of NT-H1 onto the

the heatspreader in a square 3x3 pattern as shown below:

Step 2

Caution: Applying too much thermal paste will lower heat

conductivity and cooling performance!

Continue by adding 4 larger drops (5-6mm diameter) of NT-H1 in

a square pattern at the center as shown below:

Then put the heatsink onto the CPU so that the four spring-loaded

screws align with the threads of the CPU socket. Use the sup-

plied mounting tool to tighten the screws. Perform 3 turns on each

screw, then repeat until all are fully tightened.

Caution: Gently tighten the screws until they stop, but don’t use

excessive force (max. torque 0.6 Nm).

Fastening the heatsink to the CPU

Please first take off the fan as well as the protection cover at the

bottom side of the heatsink.

Step 3

Note that you can tilt the mounting tool for reaching the screws in

case they are blocked by the heatsink fins.

Reattach the fan to the heatsink using the supplied steel clips:

Attaching the fan

Step 4

Product specificaties

Merk:	Noctua
Categorie:	Hardwarekoeling
Model:	NH-U12S TR4-SP3
Kleur van het product:	Aluminium, Beige
Gewicht:	870 g
Breedte:	125 mm
Diepte:	71 mm
Hoogte:	158 mm
Gewicht verpakking:	1260 g
Breedte verpakking:	212 mm
Diepte verpakking:	106 mm
Hoogte verpakking:	196 mm
Soort:	Koeler
Geluidsniveau (hoge snelheid:	22.4 dB
Netvoeding:	0.6 W
Materiaal:	Koper
Luchtstroom:	93.4 m³/uur
Aantal ventilatoren:	1 ventilator(en)
Spanning:	12 V
Rotatiesnelheid ( max):	1500 RPM
Rotatiesnelheid ( min):	300 RPM
(Buitenste) hoofdverpakking brutogewicht:	13600 g
Hoeveelheid per (buitenste) hoofdverpakking:	10 stuk(s)
Geschikte locatie:	Processor
Compatibele processors:	AMD Ryzen
Code geharmoniseerd systeem (HS):	84733080
Ventilator diameter:	120 mm
Aantal ventilatorbladen:	7
Supported processor sockets:	Socket TR4, Socket SP3
Pulsbreedtemodulatie-ondersteuning:	Ja
Type lager:	Self-Stabilising Oil-pressure Bearing (SSO)
Materiaal vinnen:	Aluminium
Maten ventilator (b x d x h):	120 x 120 x 25 mm
Heatsink afmetingen (B x D x H):	125 x 45 x 158 mm
Fan connector:	4-pin
Koellichaam gewicht:	695 g
Gemiddelde storingsinterval (MTTF):	150000 uur
Geluidsniveau met LNA (max):	18.6 dB
Rotatiesnelheid met LNA (max):	1200 RPM
Luchtstroom met LNA (max):	74.3 m³/uur
Adapter voor laag geluidsniveau (LNA):	Ja