NightStick XPP-5466 Handleiding

Bekijk gratis de handleiding van NightStick XPP-5466 (3 pagina’s), behorend tot de categorie Lamp. Deze gids werd als nuttig beoordeeld door 6 mensen en kreeg gemiddeld 4.2 sterren uit 2 reviews. Heb je een vraag over NightStick XPP-5466 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Bayco Products, Inc. • 640 South Sanden Blvd. • Wylie, TX 75098 • USA • 1-800-233-2155 • 1-469-326-9400 • www.nightstick.com

INS-XPP-5466-LG-21

11-11-2020

INSTALLING THE FORTEM ON TO THE HELMET

Image 4Image 5

yChoose the side of the helmet you wish to mount the light on.

yRotate the mount to orient the clamp with thumbscrew on top.

yOpen the clamp completely and fully seat over helmet brim, ensuring the clamp clears any

rubber helmet trim. (Image 4)

yTighten the clamp  rmly with included Allen wrench. (Image 5)

SCAN FOR

MOUNTING

INSTRUCTION

VIDEO

https://youtu.be/Ta0i7U-92hM

SETTING THE ANGLE OF THE LIGHT

yTwist the light left or right on the vertical pivot until beam pattern is in an ideal position.

yThe tension on the mount is meant to be  rm to maintain the aim.

yOnce aimed, the mount allows the user to position light above or below the brim by rotating

up or down as needed.

OPERATION

The FORTEM has seven lighting modes:

yConstant-on high-brightness  ashlight

yMedium-brightness  ashlight

yLow-brightness  ashlight

yConstant-on high-brightness  oodlight

yMedium-brightness  oodlight

yLow-brightness  oodlight

yConstant-on Dual-Light mode

The FORTEM has two switches, the  ashlight switch (closest to the front of the light) and

the  oodlight switch (closest to the rear of the light) providing access to all modes.

CONSTANT-ON FLASHLIGHT

Press the  ashlight switch (closest to the front of the light) until it clicks and then release

for constant-on  ashlight in high-brightness mode. Press and release this same switch again

to turn the light off.

SELECT FLASHLIGHT BRIGHTNESS LEVEL

Press and hold down the  ashlight switch. The  ashlight will cycle from high to medium

to low and then back up again at a rate of approximately one mode per second. The light will

continue to cycle up and down through the various modes as long as the  ashlight switch is

held down. When the desired brightness level is reached, simply release the  ashlight switch,

and the light will remain in that brightness mode. Pressing and holding the  ashlight switch

again will cause the light to cycle from whatever mode it is currently in. Press and release the

 ashlight switch to turn the light off.

CONSTANT-ON FLOODLIGHT

Press the  oodlight switch (closest to the rear of the light) until it clicks and then release

for constant-on  oodlight in high-brightness mode. Press and release this same switch again

to turn the light off.

Instruction Manual

FORTEM

®

XPP-5466

US PATENT 9,713,217 AND 11,019,868

THE XPP-5466 IS APPROVED FOR USE

CLASS I DIV 1 GRPS A-D T4

CLASS II & III DIV 1 GRPS E-G T135°C

CLASS I ZONE 0 AEx ia IIC T4 Ga

CLASS I ZONE 0 Ex ia IIC T4

-20ºC ≤ Tamb ≤ +40ºC

3.0V/Cell / Energizer 123

E 467756

INTRINSICALLY SAFE

SECURITE INTRINSEQUE

Conforms to:

ANSI/UL STD 913, ANSI/UL 60079-0

Certified to:

CAN/CSA STD C22.2 No 157

CAN/CSA STD C22.2 No 60079-0

CAN/CSA STD C22.2 No 60079-11

CSA STD C22.2 No 25

Bayco Products, Inc. XPP-5466

WARNINGS:

Do not change batteries in hazardous location.

Use only Energizer 123 Batteries

ID 5012927

WARNINGS - INTRINSICALLY SAFE

yWarning: Use only the approved non-rechargeable batteries listed below.

yWarning: Do NOT attempt to use rechargeable CR123A batteries with this light.

yWarning: To prevent ignition of a hazardous atmosphere, do not open the battery

compartment in the hazardous environment. This task must ONLY be performed in an area

known to be non-hazardous.

yWarning: When exchanging batteries, use only ENERGIZER CR123A BATTERIES.

yWarning: To prevent ignition of a hazardous atmosphere, the CR123A batteries must only

be exchanged in an area known to be non-hazardous.

yWarning: To reduce the risk of explosion, do not mix new non-rechargeable batteries

with used non-rechargeable batteries, or mix non-rechargeable batteries from different

manufacturers.

yWarning: Substitution of components may impair intrinsic safety.

STROBE WARNING

Exposure to strobing lights may cause dizziness, disorientation, and nausea. A very small

percentage of people suffer from photosensitive epilepsy and may experience seizures or

blackouts triggered by strobing lights. For more information from the EPILEPSY FOUNDATION

about photosensitivity and seizures, please visit

www.epilepsy.com. Anyone who has had

symptoms linked to this condition should consult a doctor before using this product.

SPECIAL INSTRUCTIONS FOR INTRINSIC SAFETY

For personal safety, always con rm the rating of any known hazardous or potentially

hazardous location where the light is to be used.

INSTALLING BATTERIES INTO THE FORTEM

Image 1Image 2Image 3

yTo install the included CR123A Lithium Batteries in the FORTEM, begin by unscrewing the

screw on the battery compartment door. (Image 1)

yInsert both batteries into the battery compartment paying attention to the battery orientation

marked on the back of the battery compartment door. (Image 2)

yRe-install the battery compartment screw by pressing the door fully closed and then

tightening the screw until it is hand tight. CAUTION: Do not cross-tread or strip the screw

threads. (Image 3)

yTest the operation of the light (see OPERATION below).

Product specificaties