Netgear WG103 Handleiding

Bekijk gratis de handleiding van Netgear WG103 (2 pagina’s), behorend tot de categorie Access point. Deze gids werd als nuttig beoordeeld door 36 mensen en kreeg gemiddeld 4.9 sterren uit 4 reviews. Heb je een vraag over Netgear WG103 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

)NSTALLATION'UIDE

Please refer to the Reference Manual on your Resource CD for instructions about

advanced configuration options.

Estimated Installation Time: 30 minutes.

Tip: Before mounting the WG103 in a high location, first set up and test the WG103 to

verify wireless network connectivity.

1.Connect the WG103 to the Computer

a.Unpack the box and verify the contents.

b.Prepare a PC with an Ethernet

adapter. If this PC is already part

of your network, record its

TCP/IP configuration settings.

Configure the PC with a static IP

address of 192.168.0.210 and

255.255.255.0 as the subnet mask.

c.Connect an Ethernet cable from

the WG103 to the PC (point A in

the illustration).

d.Securely insert the other end of the

cable into the WG103 Ethernet

port (point B in the illustration).

A

B

e.Turn on your computer, connect the power adapter to the WG103 and verify the

following:

•Power: The power light should be lit. If the power light is not lit, check the

connections and check to see if the power outlet is controlled by a wall

switch that is turned off.

•Test: The test light should be blinking when the WG103 is first turned on.

•LAN: The LAN light should be lit (amber for a 10 Mbps connection and

green for a 100 Mbps connection). If not, make sure the Ethernet cable is

securely attached at both ends.

2.Configure LAN and Wireless Access

a.Configure the WG103 Ethernet port for LAN access.

•Connect to the WG103 by opening your browser and

entering http://192.168.0.229 in the address field.

•When prompted, enter admin for the user name and

password for the password, both in lower case letters.

•Click the Basic Settings link and configure the IP Settings for your network.

b.Configure the wireless interface for wireless access. See the online help or the

Reference Manual for full instructions.

c.Test wireless connectivity using a PC with a wireless adapter configured

according to the wireless settings you just set in the WG103 to establish a

wireless connection to the WG103.

Now that you have finished the setup steps, you are ready to deploy the WG103 in

your network. If needed, you can now reconfigure the PC you used in step 1 back to

its original TCP/IP settings.

1.Disconnect the WG103 and position it where you will deploy it. The best location is

elevated, such as wall mounted or on the top of a cubicle, at the center of your

wireless coverage area, and within line of sight of all the mobile devices.

2.Position the antenna. Vertical positioning provides best side-to-side coverage.

Horizontal positioning provides best top-to-bottom coverage.

3.Connect an Ethernet cable from your WG103 to a LAN port on your router, switch, or

hub.

4.Connect the power adapter to the wireless access point and plug the power adapter in

to a power outlet. The Power and LAN lights should light up.

Tip: The WG103 supports Power Over Ethernet (PoE). If you have a switch that

provides PoE, you will not need to usto power the WG103. e the power adapter

This can be especially convenient when the WG103 is installed in a high

location far away from a power outlet.

Using a computer with an 802.11g or 802.11b wireless adapter, verify connectivity by

using a browser such as Internet Explorer or Mozilla Firefox to connect to the Internet, or

check for file and printer access on your network. In order to connect to the Internet, your

network must include a router that provides Internet access.

Note: If you cannot connect, see to Troubleshooting Tips in this guide or the Reference

Manual on the Resource CD for the ProSafe® 802.11g Wireless Access Point.

WG103_IG.fm Page 1 Monday, March 30, 2009 12:45 PM

Product specificaties