Metz Mecablitz MS-1 Digital Handleiding

Metz Flitser Mecablitz MS-1 Digital

Lees hieronder de 📖 handleiding in het Nederlandse voor Metz Mecablitz MS-1 Digital (29 pagina's) in de categorie Flitser. Deze handleiding was nuttig voor 27 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/29
MECABLITZ 15 MS-1 digital
Bedienungsanleitung Mode d’emploi
Gebruiksaanwijzing Operating instruction
Manuale istruzioni Manual de instrucciones
68
ġ
1 Safety instructions . . . . . . . . . . . . . . . . . . .69
2 Preparation . . . . . . . . . . . . . . . . . . . . . . .70
2.1 Power supply . . . . . . . . . . . . . . . . . . . . . .70
2.2 Insertion and replacement of batteries . . . . .71
2.3 Installation / Deinstallstion . . . . . . . . . . . .71
2.4 Switching the flash unit on and off . . . . . . .72
2.5 The infrared clamp . . . . . . . . . . . . . . . . . .72
3 Starting up for the first time . . . . . . . . . . .73
4 Camera-specific remote operation . . . . . . .73
4.1 General information on wireless
remote control . . . . . . . . . . . . . . . . . . . . .73
4.2 Setting remote channel and remote group . .75
5 Manual wireless slave mode . . . . . . . . . . .76
5.1 Learn function . . . . . . . . . . . . . . . . . . . . . .77
5.2 Slave mode . . . . . . . . . . . . . . . . . . . . . . . .79
6 Operation with synchronous cable . . . . . . .80
7 Operation of flash unit detached
from camera . . . . . . . . . . . . . . . . . . . . . . .81
8 Lighting OK in remote TTL mode . . . . . . . .81
9 Swivel reflectors . . . . . . . . . . . . . . . . . . . .81
9.1 Bounce diffuser . . . . . . . . . . . . . . . . . . . . .82
10 The AF auxiliary light . . . . . . . . . . . . . . . .82
11 Modelling light (ML) . . . . . . . . . . . . . . . . .83
12 Synchronisation on the 1st or 2nd shutter
curtain (REAR) . . . . . . . . . . . . . . . . . . . . . .84
13 Slow synchronisation (SLOW) . . . . . . . . . .84
13.1Using a tripod . . . . . . . . . . . . . . . . . . . . . .85
14 Care and maintenance . . . . . . . . . . . . . . .85
14.1Firmware update . . . . . . . . . . . . . . . . . . . .85
14.2 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
14.3Conditioning the flash capacitor . . . . . . . . .86
15 Troubleshooting . . . . . . . . . . . . . . . . . . . .86
16 Technical data . . . . . . . . . . . . . . . . . . . . . .86
Diagram . . . . . . . . . . . . . . . . . . . . .134-137
Introduction
Thank you for choosing a Metz product.
We are delighted that you have become a Metz
customer.
Of course you can hardly wait to use your flash unit.
It is worthwhile to read the operating manual as it is
only in this way you can learn how to use the device
without difficulties.
Please refer to the back cover at the end of the
manual.
☞
69
ġ
1 Safety instructions
• The flash unit is exclusively designed
and authorised for use in photogra-
phic applications.
• Do not flash directly into eyes from
a close distance! Direct flashing into
the eyes of persons or animals can
cause damage to the retina and
severe disruption of the vision – up
to and including permanent blind-
ness!
• The flash unit may in no event be
activated in the vicinity of inflamma-
ble gases or liquids (petroleum, sol-
vents etc.). RISK OF EXPLOSIONS!
• Never use a flash unit to photo-
graph car, bus, bicycle, motorbike
or train drivers while they are dri-
ving. Blinding the driver can lead to
an accident!
• Only use the power sources desi-
gnated and authorised in the opera-
ting manual.
• Do not open the batteries or short
them!
• In no event the batteries be exposed
to high temperatures like direct sun-
light, fire or similar!
• Remove the used batteries immedia-
tely from the device! Chemicals can
escape from used batteries (so-cal-
led “leaks”) resulting in damage to
the device!
• Batteries may not be recharged!
• Do not expose the flash unit to
water drops and splashes!
• Protect your flash unit from heat and
high air humidity! Do not keep it in
the glove compartment of your car.
• After repeated flashing, do not
touch the diffuser. Risk of burns!
• After a series of flashes with full
power and short intervals, a pause
of at least 3 minutes must be obser-
ved after each series of 20 flashes!
• When you activate the flash, there
should be no opaque material
directly in front of or on the reflector
cover (flash window). The intense
energy emissions can otherwise
lead to scorching or spotting of the
material and/or the reflector cover.
Do not dismantle the flash unit!
HIGH VOLTAGE!


Product specificaties

Merk: Metz
Categorie: Flitser
Model: Mecablitz MS-1 Digital

Heb je hulp nodig?

Als je hulp nodig hebt met Metz Mecablitz MS-1 Digital stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Flitser Metz

Handleiding Flitser

Nieuwste handleidingen voor Flitser