Metra 99-7427B Handleiding

Metra Niet gecategoriseerd 99-7427B

Lees hieronder de 📖 handleiding in het Nederlandse voor Metra 99-7427B (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 24 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4

REV. 7/16/2015 INST99-7427

Installation instructions for part 99-7427

CAUTION!

Metra recommends disconnecting the negative bat

tery terminal before beginning any installation, unless the vehicle

manufacturer recommends against so. Please check with your local

Dealership for more information. All accessories, switches, climate

controls panels, and especially air bag indicator lights must be con

nected before reconnecting the battery or cycling the ignition. Also,

do not remove the factory radio with the key in the on position, or the

vehicle running. It would be best to remove the key from the ignition

and then wait a few seconds before removing the factory radio.

• DIN Radio Provision With Pocket

• ISO DIN Radio Provision With Pocket

• PAINTED TO MATCH FACTORY DASH:

99-7427B=BLACK, 99-7427G=GRAY

• Textured To Match Factory Dash

• A) Radio Housing • B) Trim Plate • C) ISO Brackets • D) Module Brackets • E) (2) Phillips Head Screws

KIT FEATURES

KIT COMPONENTS

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: • 70-7552

Antenna Adapter: • 40-NI12

• Torx Screwdriver • Panel Removal Tool • Phillips Screwdriver

TOOLS REQUIRED

(non nav models) (w/o tech package)

A B C D E

Dash Disassembly ................................................. 2

Kit Preparation ....................................................... 2

Kit Assembly

– DIN Radio Provision With Pocket 3 ...........................

– ISO DIN Radio Provision With Pocket 3 ....................

Table of Contents

99-7427

1. Unclip and remove the panel above

the radio including the a/c vents and

the climate controls. Unplug and

remove the panel. (Figure A)

2. Unclip and remove the panel below

the radio. (Figure B)

3. Remove (6) Phillips screws securing

the radio. Unplug and remove the

radio. (Figure C)

Remove (4) Torx head screws securing

each side bracket to the factory radio.

Remove (1) Torx head screw from each

side of the module below the radio,

and then remove the radio and module.

Retain the module and (2) screws for

re-use during kit assembly. (Figure D)

Continue to kit preparation

Dash Disassembly Kit Preparation

(Figure C)

1. Attach the module brackets to the

radio housing using (2) Phillips head

screws supplied. (Figure A)

2. Secure the module to the completed

assembly using (2) factory Torx

head screws removed from dash

disassembly. (Figure B)

Continue to kit assembly

O FF

PASS

AIR

BAG

CD C HANGER

AUX IN

(Figure B)

(Figure A) (Figure D)

(Figure A)

(Figure B)

99-7427

Kit Assembly

(Figure A) (Figure A)

(Figure B) (Figure B)

DIN radio provision with pocket

1. Remove the metal DIN sleeve from

the aftermarket radio.

Slide the sleeve into the Radio

Housing and secure by bending the

metal locking tabs outward. (Figure A)

3. Slide the radio back into the sleeve

until it clicks in.

(Figure B)

4. Locate the factory wiring harness

and antenna plug in the dash and

make all necessary connections to

the radio. Metra recommends using

the proper mating adapters from

Metra and/or AXXESS. Re-connect

the negative battery terminal and

test the radio for proper operation.

5. Mount the new radio assembly into

the dash and reassemble the dash in

reverse order of disassembly.

ISO DIN radio provision with pocket

Remove the metal DIN sleeve and

trim ring from the aftermarket radio.

2. Mount the ISO brackets to the radio

using screws supplied with the

radio.

(Figure A)

3. Slide the completed assembly into

the Radio Housing until it clicks in.

(Figure B)

4. Snap the Trim Plate onto the front

of the Radio Housing.

(Figure B)

5. Locate the factory wiring harness

and antenna plug in the dash and

make all necessary connections

to the radio. Metra recommends

using the proper mating adapters

from Metra and/or AXXESS.

Re-connect the negative battery

terminal and test the radio for

proper operation.

6. Mount the new radio assembly into

the dash and reassemble the dash

in reverse order of disassembly.

Product specificaties

Merk:	Metra
Categorie:	Niet gecategoriseerd
Model:	99-7427B

Heb je hulp nodig?

Als je hulp nodig hebt met Metra 99-7427B stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Metra

Metra FD-BROPOD1 Handleiding

3 April 2024

Metra AXDIS-HK4 Handleiding

19 Maart 2024

Metra TE-AJPKT Handleiding

27 Februari 2024

Metra 99-7342 Handleiding

6 Januari 2024

Metra 70-7903 Handleiding

6 Januari 2024

Metra 99-7888 Handleiding

6 Januari 2024

Metra 99-3020 Handleiding

6 Januari 2024

Metra 99-7510 Handleiding

6 Januari 2024

Metra 70-1731 Handleiding

6 Januari 2024

Metra 99-8222BR Handleiding

6 Januari 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Bauknecht KSI 18GF2 P2 Handleiding

27 April 2024

Fakir Artemis TS 150 Handleiding

26 April 2024

Sony UTX-M03 Handleiding

26 April 2024

Sony URX-P03 Handleiding

26 April 2024

Sony WRU-806B Handleiding

26 April 2024

Sony UTX-B03 Handleiding

26 April 2024

Sony UTX-P03 Handleiding

26 April 2024

Sony ODS-L10 Handleiding

26 April 2024

Sony PDW-U4 Handleiding

26 April 2024

Sony NXL-FR318 Handleiding

26 April 2024