Metra 70-8902 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Metra 70-8902 (3 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 7 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/3
Orange - Illumination
Black - Chassis Ground
Blue - Power Antenna
Red - 12 Volts Switched Power
Yellow - 12 Volts Constant Power
Receiver Wiring Adaptor
120 70-8902
Revision 10/10/17
STEP 1 -- MATCH & CONNECT WIRES
*120708902*
IMPORTANT
Before starting, compare items on your invoice with items
received. Thoroughly check packing materials. If an item
is missing, please call Crutchfield at 1-888-955-6000.
White - Left Front Channel
Green - Left Rear Channel
Gray - Right Front Channel
Violet - Right Rear Channel
Copyright 2017 Crutchfield Corporation
(connects to Orange or
Orange/White on receiver)
Blue - Power Antenna
Blue/White - Amplifier Turn-On
These Blue & Blue/White Wires apply to Subaru Forester only.
This Blue Wire applies to Subaru Legacy and Outback only.
Connects to RCA Outputs on Receiver
Match wires below to the matching function of each wire on your receiver (refer to instructions supplied with receiver). The wire colors of your
new receiver may, or may not, match the wire colors of the adaptor. Match adaptor and receiver wires by function, disregarding color.
Your receiver illumination wire could be Orange or Orange/White. As with other wires, match this wire to the illumination wire in this harness
by function, not by color. If your receiver does not have an illumination wire, tape off the illumination wire.
Individually tape off any unused wires.
Make final wiring connections following instructions on the next page.
Continue with these instructions to match and connect wires on the next page.
A.
B.
C.
D.
Receiver Wiring Adaptor
120 70-8902
Copyright 2017 Crutchfield Corporation
STEP 1 -- (continued)
Page 2
Connect to Steering Wheel Control Port on receiver
AUX Input (if equipped or optional)
Black - Chassis Ground
Green/Violet - Reverse (used only if installing a
video/NAV receiver along with a backup camera)
Blue/White - Amplifier Turn-On
Red - 12 Volts Switched Power
Connect to the 120ASWC1,
disregarding the harness that
came with the ASWC1. It will not
be used in the installation.
Connect to Red and Black wires from the harness on
page 1 and to matching wires from the receiver.
Use the 3.5mm 2-wire adaptor included in the 120ASWC1 for JVC
and Kenwood with the Blue/Yellow steering wheel control input wire.
Connect the Brown wire on the adaptor to the Blue/Yellow wire.
This Blue/White Wire applies to Subaru Legacy and Outback only.
An adaptor may be required if the receiver's
AUX input requires a 3.5mm male connector.
Blue/Pink - VSS (Forester Only)
Receiver Wiring Adaptor Connections
120 70-8902
Page 3
STEP 2 -- CONTINUED
A. Strip wires back 1/2”.
B. Twist wires together and
insert in crimp cap.
C. Squeeze middle of cap
for tight connection.
Copyright 2017 Crutchfield Corporation
STEP 3 -- APPLICATION
When ready to install the receiver, plug
the Wiring Adaptor from the new receiver
or receiver assembly into the factory
radio harness(es) in the vehicle dash.
D. Complete crimp connections
for all necessary wires.
E. Be sure to wrap any wires from
the Wiring Adaptor that are
not necessary (wires with no
match from the new receiver)
with electrical tape.
STEP 2 -- CRIMP CONNECTIONS
Tools & Parts
Required
Wire Stripper/Crimp Tool Crimp Caps
Unused Wire (tape over bare wires)
Receiver Wiring Adaptor
Generic Illustration
Generic Illustration


Product specificaties

Merk: Metra
Categorie: Niet gecategoriseerd
Model: 70-8902

Heb je hulp nodig?

Als je hulp nodig hebt met Metra 70-8902 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Metra

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd