Metra 95-8210 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Metra 95-8210 (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 8 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8
CAUTION!
All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
Metra. The World’s Best Kits.®MetraOnline.com © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 5/8/18 INST95-8210
I N S TA L L AT I O N I N S T R U C T I O N S
95-8210
KIT FEATURES
ISO DDIN radio provision
KIT COMPONENTS
• A) Radio trim panel • B) Radio brackets • C) (4) #8 x 3/8 Phillips screws
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• 10mm socket wrench
TABLE OF CONTENTS
Dash Disassembly ..................................................2
Kit Assembly ..........................................................3
WIRING & ANTENNA CONNECTIONS
(sold separately)
Wiring Harness: 70-1761 • TYTO-01 (for amplified
models)
Antenna Adapter: Not required
A B C
Toyota 4-Runner Limited 2003-2009
(without navigation)
1.800.221.0932
|
MetraOnline.com
2
DASH DISASSEMBLY
1. Unsnap and remove trim from around
shifter. (Figure A)
2. Unsnap and remove center console
cover. (Figure B)
3. Unsnap trim ring from around ignition
key cylinder.
4. Remove (1) 10mm bolt from bottom
right side of panel below steering
column. Unsnap panel and pull away to
gain access behind panel. (Figure C)
5. Remove (1) 10mm bolt on bottom left
of center panel behind panel below
steering column. (Figure D)
(Figure B)
(Figure C)
(Figure D)(Figure A)
6. Remove (1) 10mm bolt beneath climate
control behind pocket door.(Figure E)
Unsnap climate control, unplug and
remove climate control. (Figure F)
7. Remove (2) 10mm bolts beneath radio
behind climate controls. (Figure G)
8. Unsnap and remove entire center panel
around radio.
9. Remove (2) 10mm bolts securing radio.
Unplug and remove radio. (Figure H)
Continue to Kit Assembly
PASSENGER
(Figure F)
(Figure G)
(Figure H)(Figure E)
REV. 5/8/2018 INST95-8210 3
1. Secure the
radio brackets
to the
radio
trim panel
using (4) #8 x 3/8” Phillips
screws supplied. (Figure A)
2. Slide the radio into the bracket/panel
assembly, then secure it using the
screws supplied with the radio. (Figure
B)
3. Locate the factory wiring harness and
antenna connector in the dash, and
complete all necessary connections to
the radio. Metra recommends using the
proper mating adapter from Metra and/
or AXXESS. Test the radio for proper
operation.
4. Secure the radio assembly to the dash
using the factory hardware.
The top bar can be removed or left Note:
on. (Figure C).
5.
Reassemble the dash in reverse order of
disassembly to complete the installation
.
KIT ASSEMBLY
(Figure A) (Figure B) (Figure C)


Product specificaties

Merk: Metra
Categorie: Niet gecategoriseerd
Model: 95-8210

Heb je hulp nodig?

Als je hulp nodig hebt met Metra 95-8210 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Metra

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd