Metra 70-1770 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Metra 70-1770 (3 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 18 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/3
Receiver Wiring Adaptor
120 70-1770
Revision 10/17/16
Red - 12 Volts Switched Power
Yellow - 12 Volts Constant Power
Black - Chassis Ground
Blue - Power Antenna
STEP 1 -- CONNECT WIRES
Connect wires below to the matching function of each wire on your receiver (refer to instruction supplied with receiver).
The wire colors of your new receiver may, or may not, match the wire colors of the adaptor. Match adaptor and receiver
wires by function, disregarding color.
Your receiver illumination wire could be Orange or Orange/White. As with other wires, match this wire to the illumination wire
in this harness by function, not by color. If your receiver does not have an illumination wire, tape off the illumination wire.
If there is no Ground wire in the factory harness, connect new receiver’s Ground wire to vehicle chassis.
Individually tape off any unused wires.
Make final connections following instructions on page 3.
Power Plug of Harness Set
(see speaker plug instructions on page 2)
*120701770*
Orange - Illumination
Before starting, compare items on your invoice with items
received. Carefully check through packaging material. If an
item is missing, please call Crutchfield at 1-888-955-6000.
IMPORTANT
A.
B.
C.
D.
E.
Copyright 2016 Crutchfield Corporation
Receiver Wiring Adaptor
120 70-1770
STEP 1 -- CONNECT WIRES (continued)
Speaker Plug of Harness Set
White - Left Front Speaker Positive
Violet/Black - Right Rear Speaker Negative
Violet - Right Rear Speaker Positive
Green - Left Rear Speaker Positive
Gray - Right Front Speaker Positive
Gray/Black - Right Front Speaker Negative
Green/Black - Left Rear Speaker Negative
White/Black - Left Front Speaker Negative
Page 2
The speaker plug in this harness set may not be directly
compatible with your vehicle’s wiring if the vehicle is equipped
with a JBL, or Premium Sound amplifier. An additional adaptor
may be needed to correctly interface an aftermarket receiver
with a JBL or Premium Sound amplifier.
In some cases, Ford’s front speaker negative leads (wires) are
reversed. To test, plug in the wiring harness. Touch the
positive and negative leads of the left speaker to a “C” or “D”
cell battery (1.5 volts). If you hear a “pop”, your vehicle is
wired normally. If “pop” is heard, connect the front speaker no
negative leads in reverse. Left front speaker negative
becomes right front speaker negative.
Individually tape off any unused wires.
Make final connections following instructions on page 3.
F.
G.
H.
I.
Copyright 2016 Crutchfield Corporation
Receiver Wiring Adaptor Connections
120 70-1770
Page 3
STEP 2 -- CONTINUED
A. Strip wires back 1/2”.
B. Twist wires together and
insert in crimp cap.
C. Squeeze middle of cap
for tight connection.
STEP 3 -- APPLICATION
D. Complete crimp connections
for all necessary wires.
E. Be sure to wrap any wires from
the Wiring Adaptor that are
not necessary (wires with no
match from the new receiver)
with electrical tape.
STEP 2 -- CRIMP CONNECTIONS
Tools & Parts
Required
Wire Stripper/Crimp Tool Crimp Caps
Unused Wire (tape over bare wires)
Receiver Wiring Adaptor
Generic Illustration
Copyright 2016 Crutchfield Corporation
When ready to install the receiver, plug
the Wiring Adaptor from the new receiver
or receiver assembly into the factory
radio harness(es) in the vehicle dash.
Generic Illustration


Product specificaties

Merk: Metra
Categorie: Niet gecategoriseerd
Model: 70-1770

Heb je hulp nodig?

Als je hulp nodig hebt met Metra 70-1770 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Metra

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd