Makita 4100KB/1 Handleiding
Makita
Snijmachine
4100KB/1
Lees hieronder de 📖 handleiding in het Nederlandse voor Makita 4100KB/1 (12 pagina's) in de categorie Snijmachine. Deze handleiding was nuttig voor 46 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/12
INSTRUCTION MANUAL
Dustless Cutter
4100KB
ENGLISH: Original instructions
DOUBLE INSULATION
Read before use.
2 ENGLISH
SPECIFICATIONS
Model: 4100KB
Wheel diameter 125 mm
Max. wheel thickness 2.2 mm
Max. cutting capacities 40 mm
Rated speed (n) 12,200 min-1
Overall length 231 mm
Net weight 3.0 kg
Safety class /II
• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange
without notice.
• Specicationsmaydifferfromcountrytocountry.
• WeightaccordingtoEPTA-Procedure01/2014
Symbols
The following show the symbols used for the equip-
ment. Be sure that you understand their meaning before
use.
Read instruction manual.
DOUBLE INSULATION
Wear safety glasses.
Only for EU countries
Do not dispose of electric equipment
together with household waste material! In
observance of the European Directive, on
Waste Electric and Electronic Equipment
and its implementation in accordance with
national law, electric equipment that have
reached the end of their life must be col-
lected separately and returned to an envi-
ronmentally compatible recycling facility.
Intended use
The tool is intended for cutting in brick and concrete
without the use of water.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated and can, therefore, also be used
from sockets without earth wire.
For public low-voltage distribution
systems of between 220 V and 250 V
Switching operations of electric apparatus cause volt-
ageuctuations.Theoperationofthisdeviceunder
unfavorable mains conditions can have adverse effects
to the operation of other equipment. With a mains
impedance equal or less than 0.37 Ohms it can be pre-
sumed that there will be no negative effects. The mains
socket used for this device must be protected with a
fuse or protective circuit breaker having slow tripping
characteristics.
Noise
The typical A-weighted noise level determined accord-
ing to EN60745:
Sound pressure level (L
pA) : 96 dB(A)
Sound power level (L
WA) : 107 dB (A)
Uncertainty (K) : 3 dB(A)
WARNING: Wear ear protection.
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN60745:
Work mode: concrete cutting
Vibration emission (a
h) : 6.0 m/s2
Uncertainty (K) : 1.5 m/s
2
NOTE: The declared vibration emission value has
been measured in accordance with the standard test
method and may be used for comparing one tool with
another.
NOTE: The declared vibration emission value
may also be used in a preliminary assessment of
exposure.
3 ENGLISH
WARNING:
The vibration emission during actual
use of the power tool can differ from the declared emission
value depending on the ways in which the tool is used.
WARNING: Be sure to identify safety measures
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it is
running idle in addition to the trigger time).
EC Declaration of Conformity
For European countries only
The EC declaration of conformity is included as Annex A
to this instruction manual.
SAFETY WARNINGS
General power tool safety warnings
WARNING: Read all safety warnings, instruc-
tions, illustrations and speciî‚¿cations provided
with this power tool. Failure to follow all instructions
listedbelowmayresultinelectricshock,reand/or
seriousinjury.
Save all warnings and instruc-
tions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
1. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
2. Do not operate power tools in explosive atmo-
spheres, such as in the presence of ammable
liquids, gases or dust.Powertoolscreatesparks
which may ignite the dust or fumes.
3. Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
Electrical Safety
1. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodiedplugsandmatchingoutletswill
reduce risk of electric shock.
2. Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of elec-
tric shock if your body is earthed or grounded.
3. Do not expose power tools to rain or wet con-
ditions. Water entering a power tool will increase
the risk of electric shock.
4. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
5. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
6. If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
7. Use of power supply via an RCD with a rated
residual current of 30 mA or less is always
recommended.
8.
Power tools can produce electromagnetic î‚¿elds
(EMF) that are not harmful to the user. However,
users of pacemakers and other similar medical
devices should contact the maker of their device and/
or doctor for advice before operating this power tool.
9. Do not touch the power plug with wet hands.
10. If the cord is damaged, have it replaced by the
manufacturer or his agent in order to avoid a
safety hazard.
Personal Safety
1. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the inuence of drugs, alcohol or med-
ication. A moment of inattention while operating
powertoolsmayresultinseriouspersonalinjury.
2. Use personal protective equipment. Always
wear eye protection.Protectiveequipmentsuch
as a dust mask, non-skid safety shoes, hard hat or
hearing protection used for appropriate conditions
willreducepersonalinjuries.
3. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
yourngerontheswitchorenergisingpowertools
that have the switch on invites accidents.
4. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
resultinpersonalinjury.
5. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
6. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair and clothing away
from moving parts.Looseclothes,jewelleryor
long hair can be caught in moving parts.
7. If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
8.
Do not let familiarity gained from frequent use
of tools allow you to become complacent and
ignore tool safety principles. A careless action can
causesevereinjurywithinafractionofasecond.
9. Always wear protective goggles to protect
your eyes from injury when using power tools.
The goggles must comply with ANSI Z87.1 in
the USA, EN 166 in Europe, or AS/NZS 1336
in Australia/New Zealand. In Australia/New
Zealand, it is legally required to wear a face
shield to protect your face, too.
Product specificaties
| Merk: | Makita |
| Categorie: | Snijmachine |
| Model: | 4100KB/1 |
Heb je hulp nodig?
Als je hulp nodig hebt met Makita 4100KB/1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Snijmachine Makita
2 Juli 2023
1 Juni 2023
10 Mei 2023
4 Mei 2023
1 Mei 2023
25 April 2023
21 April 2023
16 April 2023
3 April 2023
23 Maart 2023
Handleiding Snijmachine
- Snijmachine Electrolux
- Snijmachine Bosch
- Snijmachine Grundig
- Snijmachine Kenwood
- Snijmachine Krups
- Snijmachine Quigg
- Snijmachine Siemens
- Snijmachine Tefal
- Snijmachine Unold
- Snijmachine Ade
- Snijmachine Ambiano
- Snijmachine Arendo
- Snijmachine Ariete
- Snijmachine Bartscher
- Snijmachine Beem
- Snijmachine Beper
- Snijmachine Berkel
- Snijmachine Bestron
- Snijmachine Bifinet
- Snijmachine Bifinett
- Snijmachine Blaupunkt
- Snijmachine Borner
- Snijmachine Brother
- Snijmachine Domo
- Snijmachine Domoclip
- Snijmachine Dremel
- Snijmachine Efbe-schott
- Snijmachine Emga
- Snijmachine Enkho
- Snijmachine Ernesto
- Snijmachine Esperanza
- Snijmachine ETA
- Snijmachine Exquisit
- Snijmachine Fagor
- Snijmachine Ferm
- Snijmachine Festool
- Snijmachine Fritel
- Snijmachine G3 Ferrari
- Snijmachine Gastroback
- Snijmachine Gastronoma
- Snijmachine Genius
- Snijmachine Gorenje
- Snijmachine Gourmetmaxx
- Snijmachine Graef
- Snijmachine Gude
- Snijmachine H.Koenig
- Snijmachine Hendi
- Snijmachine Hikoki
- Snijmachine Hyundai
- Snijmachine Ices
- Snijmachine Kalorik
- Snijmachine Kinzo
- Snijmachine Korona
- Snijmachine Livoo
- Snijmachine Mach
- Snijmachine Magic Chef
- Snijmachine Magimix
- Snijmachine Melissa
- Snijmachine Mia
- Snijmachine MPM
- Snijmachine Parkside
- Snijmachine Philco
- Snijmachine Powerfix
- Snijmachine Powerplus
- Snijmachine PowerTec Kitchen
- Snijmachine Presto
- Snijmachine Primo
- Snijmachine Princess
- Snijmachine ProfiCook
- Snijmachine Proline
- Snijmachine Ritter
- Snijmachine Rommelsbacher
- Snijmachine Rotel
- Snijmachine Russell Hobbs
- Snijmachine Saro
- Snijmachine Saturn
- Snijmachine Sencor
- Snijmachine Severin
- Snijmachine Silvercrest
- Snijmachine Skil
- Snijmachine Sunbeam
- Snijmachine Team
- Snijmachine Trebs
- Snijmachine Tristar
- Snijmachine Turmix
- Snijmachine Ufesa
- Snijmachine Venga
- Snijmachine Waves
- Snijmachine Westfalia
- Snijmachine Zelmer
- Snijmachine Jata
- Snijmachine OK
- Snijmachine Oster
- Snijmachine OXO
- Snijmachine Clas Ohlson
- Snijmachine Black And Decker
- Snijmachine Clatronic
- Snijmachine Concept
- Snijmachine Cuisinart
- Snijmachine ECG
- Snijmachine Heinner
- Snijmachine Orbegozo
- Snijmachine Trisa
- Snijmachine Vox
- Snijmachine Wilfa
- Snijmachine Nutrichef
- Snijmachine Hobart
- Snijmachine Nevir
- Snijmachine Eldom
- Snijmachine JAC
- Snijmachine Coline
- Snijmachine Rösle
- Snijmachine Sammic
- Snijmachine Tescoma
- Snijmachine RIDGID
- Snijmachine Riviera And Bar
- Snijmachine CaterChef
- Snijmachine RGV
- Snijmachine De Buyer
- Snijmachine Bron-Coucke
- Snijmachine FAC
- Snijmachine Avantco
- Snijmachine Makeblock
- Snijmachine Globe
- Snijmachine Baker's Mark
- Snijmachine Louis Tellier
- Snijmachine GARDE
- Snijmachine Pro-Cut
- Snijmachine Jokari
- Snijmachine Kleva
- Snijmachine Backyard Pro Butcher Series
- Snijmachine Prince Castle
- Snijmachine Boska
Nieuwste handleidingen voor Snijmachine
10 April 2024
10 April 2024
27 Maart 2024
27 Maart 2024
14 Maart 2024
13 Maart 2024
1 Maart 2024
24 Februari 2024
15 Februari 2024
30 Januari 2024