Makita CC301DWAE Handleiding
Makita
Snijmachine
CC301DWAE
Lees hieronder de 📖 handleiding in het Nederlandse voor Makita CC301DWAE (12 pagina's) in de categorie Snijmachine. Deze handleiding was nuttig voor 47 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/12
INSTRUCTION MANUAL
Cordless Cutter
CC301D
ENGLISH: Original instructions
Read before use.
2 ENGLISH
SPECIFICATIONS
Model: CC301D
Diamond wheel diameter 85 mm
Max. wheel thickness 0.8 mm
Max. Cutting depth at 0° bevel 25.5 mm
at 45° bevel 16.5 mm
Rated speed 1,500 min-1
Rated voltage D.C. 10.8 V
Battery cartridge BL1015, BL1020B BL1040B
Overall length 313 mm 331 mm
Net weight 1.8 kg 1.9 kg
• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange
without notice.
• Specicationsandbatterycartridgemaydifferfromcountrytocountry.
• Weight, with battery cartridge, according to EPTA-Procedure 01/2003
Symbols
The following show the symbols used for the equip-
ment. Be sure that you understand their meaning before
use.
Read instruction manual.
Wear safety glasses.
Only for EU countries
Do not dispose of electric equipment
together with household waste material! In
observance of the European Directive, on
Waste Electric and Electronic Equipment
and its implementation in accordance with
national law, electric equipment that have
reached the end of their life must be col-
lected separately and returned to an envi-
ronmentally compatible recycling facility.
Intended use
The tool is intended for cutting in glass and masonry
materials with a diamond wheel and water.
Noise
The typical A-weighted noise level determined accord-
ing to EN60745:
Sound pressure level (LpA ) : 84 dB(A)
Sound power level (LWA) : 95 dB (A)
Uncertainty (K) : 3 dB(A)
WARNING: Wear ear protection.
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN60745:
Work mode: concrete cutting
Vibration emission (ah) : 2.5 m/s2 or less
Uncertainty (K) : 1.5 m/s2
NOTE: The declared vibration emission value has
been measured in accordance with the standard test
method and may be used for comparing one tool with
another.
NOTE: The declared vibration emission value
may also be used in a preliminary assessment of
exposure.
WARNING: The vibration emission during actual
use of the power tool can differ from the declared
emission value depending on the ways in which the
tool is used.
WARNING: Be sure to identify safety measures
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it is
running idle in addition to the trigger time).
EC Declaration of Conformity
For European countries only
The EU declaration of conformity is included as Annex A
to this instruction manual.
SAFETY WARNINGS
General power tool safety warnings
WARNING: Read all safety warnings and
all instructions. Failure to follow the warnings and
instructionsmayresultinelectricshock,reand/or
seriousinjury.
Save all warnings and instruc-
tions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
3 ENGLISH
Work area safety
1. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
2. Do not operate power tools in explosive atmo-
spheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
3. Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
Electrical Safety
1. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodiedplugsandmatchingoutletswill
reduce risk of electric shock.
2. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of elec-
tric shock if your body is earthed or grounded.
3. Do not expose power tools to rain or wet con-
ditions. Water entering a power tool will increase
the risk of electric shock.
4. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
5. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
6. If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
Personal Safety
1. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the inuence of drugs, alcohol or med-
ication. A moment of inattention while operating
powertoolsmayresultinseriouspersonalinjury.
2.
Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask, non-
skid safety shoes, hard hat, or hearing protection used for
appropriateconditionswillreducepersonalinjuries.
3. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
yourngerontheswitchorenergisingpowertools
that have the switch on invites accidents.
4. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
resultinpersonalinjury.
5. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
6. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing, and gloves
away from moving parts.Looseclothes,jewel-
lery or long hair can be caught in moving parts.
7. If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
Power tool use and care
1. Do not force the power tool. Use the correct
power tool for your application. The correct
powertoolwilldothejobbetterandsaferatthe
rate for which it was designed.
2. Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.
3.
Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
4.
Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool
or these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
5. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
6. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
7.
Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
Battery tool use and care
1. Recharge only with the charger speciî‚¿ed by
the manufacturer. A charger that is suitable for
onetypeofbatterypackmaycreateariskofre
when used with another battery pack.
2. Use power tools only with speciî‚¿cally desig-
nated battery packs. Use of any other battery
packsmaycreateariskofinjuryandre.
3. When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from one
terminal to another. Shorting the battery termi-
nalstogethermaycauseburnsorare.
4.
Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact acci-
dentally occurs, ush with water. If liquid con-
tacts eyes, additionally seek medical help. Liquid
ejectedfromthebatterymaycauseirritationorburns.
Service
1. Have your power tool serviced by a qualiî‚¿ed
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
2. Follow instruction for lubricating and chang-
ing accessories.
3. Keep handles dry, clean and free from oil and
grease.
Product specificaties
| Merk: | Makita |
| Categorie: | Snijmachine |
| Model: | CC301DWAE |
Heb je hulp nodig?
Als je hulp nodig hebt met Makita CC301DWAE stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Snijmachine Makita
2 Juli 2023
1 Juni 2023
10 Mei 2023
4 Mei 2023
1 Mei 2023
25 April 2023
21 April 2023
16 April 2023
3 April 2023
23 Maart 2023
Handleiding Snijmachine
- Snijmachine Electrolux
- Snijmachine Bosch
- Snijmachine Grundig
- Snijmachine Kenwood
- Snijmachine Krups
- Snijmachine Quigg
- Snijmachine Siemens
- Snijmachine Tefal
- Snijmachine Unold
- Snijmachine Ade
- Snijmachine Ambiano
- Snijmachine Arendo
- Snijmachine Ariete
- Snijmachine Bartscher
- Snijmachine Beem
- Snijmachine Beper
- Snijmachine Berkel
- Snijmachine Bestron
- Snijmachine Bifinet
- Snijmachine Bifinett
- Snijmachine Blaupunkt
- Snijmachine Borner
- Snijmachine Brother
- Snijmachine Domo
- Snijmachine Domoclip
- Snijmachine Dremel
- Snijmachine Efbe-schott
- Snijmachine Emga
- Snijmachine Enkho
- Snijmachine Ernesto
- Snijmachine Esperanza
- Snijmachine ETA
- Snijmachine Exquisit
- Snijmachine Fagor
- Snijmachine Ferm
- Snijmachine Festool
- Snijmachine Fritel
- Snijmachine G3 Ferrari
- Snijmachine Gastroback
- Snijmachine Gastronoma
- Snijmachine Genius
- Snijmachine Gorenje
- Snijmachine Gourmetmaxx
- Snijmachine Graef
- Snijmachine Gude
- Snijmachine H.Koenig
- Snijmachine Hendi
- Snijmachine Hikoki
- Snijmachine Hyundai
- Snijmachine Ices
- Snijmachine Kalorik
- Snijmachine Kinzo
- Snijmachine Korona
- Snijmachine Livoo
- Snijmachine Mach
- Snijmachine Magic Chef
- Snijmachine Magimix
- Snijmachine Melissa
- Snijmachine Mia
- Snijmachine MPM
- Snijmachine Parkside
- Snijmachine Philco
- Snijmachine Powerfix
- Snijmachine Powerplus
- Snijmachine PowerTec Kitchen
- Snijmachine Presto
- Snijmachine Primo
- Snijmachine Princess
- Snijmachine ProfiCook
- Snijmachine Proline
- Snijmachine Ritter
- Snijmachine Rommelsbacher
- Snijmachine Rotel
- Snijmachine Russell Hobbs
- Snijmachine Saro
- Snijmachine Saturn
- Snijmachine Sencor
- Snijmachine Severin
- Snijmachine Silvercrest
- Snijmachine Skil
- Snijmachine Sunbeam
- Snijmachine Team
- Snijmachine Trebs
- Snijmachine Tristar
- Snijmachine Turmix
- Snijmachine Ufesa
- Snijmachine Venga
- Snijmachine Waves
- Snijmachine Westfalia
- Snijmachine Zelmer
- Snijmachine Jata
- Snijmachine OK
- Snijmachine Oster
- Snijmachine OXO
- Snijmachine Clas Ohlson
- Snijmachine Black And Decker
- Snijmachine Clatronic
- Snijmachine Concept
- Snijmachine Cuisinart
- Snijmachine ECG
- Snijmachine Heinner
- Snijmachine Orbegozo
- Snijmachine Trisa
- Snijmachine Vox
- Snijmachine Wilfa
- Snijmachine Nutrichef
- Snijmachine Hobart
- Snijmachine Nevir
- Snijmachine Eldom
- Snijmachine JAC
- Snijmachine Coline
- Snijmachine Rösle
- Snijmachine Sammic
- Snijmachine Tescoma
- Snijmachine RIDGID
- Snijmachine Riviera And Bar
- Snijmachine CaterChef
- Snijmachine RGV
- Snijmachine De Buyer
- Snijmachine Bron-Coucke
- Snijmachine FAC
- Snijmachine Avantco
- Snijmachine Makeblock
- Snijmachine Globe
- Snijmachine Baker's Mark
- Snijmachine Louis Tellier
- Snijmachine GARDE
- Snijmachine Pro-Cut
- Snijmachine Jokari
- Snijmachine Kleva
- Snijmachine Backyard Pro Butcher Series
- Snijmachine Prince Castle
- Snijmachine Boska
Nieuwste handleidingen voor Snijmachine
10 April 2024
10 April 2024
27 Maart 2024
27 Maart 2024
14 Maart 2024
13 Maart 2024
1 Maart 2024
24 Februari 2024
15 Februari 2024
30 Januari 2024