Lancom LN-860 Handleiding

Bekijk gratis de handleiding van Lancom LN-860 (1 pagina’s), behorend tot de categorie Access point. Deze gids werd als nuttig beoordeeld door 28 mensen en kreeg gemiddeld 4.0 sterren uit 6 reviews. Heb je een vraag over Lancom LN-860 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

4

Please observe the

following when setting

up the device

AFor devices to be

operated on the

desktop, please attach

the adhesive rubber

footpads

ADo not rest any objects

on top of the device

AKeep the ventilation

slots on the side of

the device clear of

obstruction

ALockable wall and

ceiling mounting with

the LANCOM Wall

Mount (LN) (available as

an accessory)

aPower

OffDevice switched off

Green,

constantly on*

Device operational

resp. device paired / claimed and LANCOM

Management Cloud (LMC) accessible.

Red/green

blinking

Conguration password not set. Without a

conguration password, the conguration

data in the device is unprotected.

Orange/green

blinking alternately

with the WLAN

link LED

At least one Wi-Fi module is in

managed mode and has not found a

WLAN controller yet. The corresponding

Wi-Fi module(s) is/are switched off until a

WLAN controller has been found to supply

a congu ration, or until being switched

manually into another operating mode.

Orange/red

blinking alternately

with the WLAN

link LED

At least one Wi-Fi module is in managed

mode and has found a WLAN controller.

However, the WLAN controller cannot

assign a conguration because the

rmware and/or the device's loader

version is not compatible with the WLAN

controller.

1x green inverse

blinking*

Connection to the LMC active, pairing OK,

claiming error.

2x green inverse

blinking*

Pairing error, resp.

LMC activation code / PSK not available.

3x green inverse

blinking*

LMC not accessible, resp.

communication error.

ab

bWLAN link

OffNo Wi-Fi network dened or Wi-Fi module

deactivated. The Wi-Fi module is not

transmitting beacons.

GreenAt least one Wi-Fi network dened and

Wi-Fi module activated. The Wi-Fi module

is transmitting beacons.

Green

inverse ashing

Number of ashes = number of connected

Wi-Fi stations and P2P wireless

connections, followed by a pause (default).

Alternatively the ashing frequency can

indicate signal strength over the dened

P2P link or the signal strength between the

access point and the device operating in

client mode.

Green blinkingDFS scanning or other scan procedure.

Red blinkingHardware error in the Wi-Fi module.

MOUNTING AND CONNECTING THE DEVICE

Hardware

Power supply12 V DC, external power adapter (110 or 230 V) with bayonet connector to secure against

disconnection or PoE based on 802.3at via ETH1

Power consumptionApprox. 15.1 W via 12 V / 2 A power adapter (value refers to the total power consumption of

access point and power adapter),

Approx. 14.9 W via PoE (value solely refers to the power consumption of the access point)

EnvironmentTemperature range 0–45 °C (vertical wall mount with LANCOM Wall Mount (LN)),

0-37 °C (horizontal ceiling mount with LANCOM Wall Mount (LN))

Access point overheating is avoided by automatic throttling of the Wi-Fi modules

Humidity 0-95 %; non-condensing

HousingRobust synthetic housing, rear connectors, ready for wall and ceiling mounting; measures

205 x 42 x 205 mm (W x H x D)

Number of fansNone; fanless design, no rotating parts, high MTBF

Wi-Fi

Frequency band 2400-2483.5 MHz (ISM) or 5180-5700 MHz (restrictions vary between countries)

Radio channels 2.4 GHzUp to 13 channels, max. 3 non-overlapping (2.4 GHz band)

Radio channels 5 GHzUp to 19 non-overlapping channels (automatic dynamic channel selection required)

Interfaces

ETH1 (PoE)10 / 100 / 1000 Base-TX, autosensing, auto node hub,

PoE adapter compliant with IEEE 802.3at required

ETH210 / 100 / 1000 Base-TX, autosensing, auto node hub

Serial interfaceSerial conguration interface / COM-port (8-pin mini-DIN): 9,600 - 115,000 baud

Declaration of conformity

The Declaration of Conformity can be found on the product page of our website www.lancom-systems.com

Package content

ManualInstallation Guide (DE/EN), Quick Reference Guide (DE/EN)

Antennas (only LN-862)Four 3 dBi dipole dual-band antennas

CableEthernet cable, 3 m

Power adapterExternal power adapter, NEST 12 V / 1.5 A DC/S, barrel connector 2.1 / 5.5 mm bayonet,

LANCOM item no. 111507 (EU, 230 V); LANCOM item no. 111302 (UK, 230 V)

LANCOM, LANCOM Systems and LCOS are registered trademarks. All other names or descriptions used may be trademarks or registered

trademarks of their owners. Subject to change without notice. No liability for technical errors and/or omissions. 111553/0317

TECHNICAL DETAILS

LANCOM LN-860

LANCOM LN-862

Quick Reference Guide

Ethernet interface

Use the cable with the Ethernet

connectors to connect interface

ETH1 (PoE) or ETH2 to your PC

or a LAN switch.

Power

When connecting the cable to the

device, turn the bayonet connector

90° clockwise until it clicks into

place.

Use only the supplied power adapter!

Serial interface

You can congure the device by

connecting it to a PC with a

conguration cable

(separately available).

bcd

Please note that when operating both Wi-Fi modules in the same frequency band, mutual

interference cannot be ruled out

5

DC 12 VResetConfig (Com)

c

b

d

Wi-Fi antennas (only LN-862)

Screw the supplied Wi-Fi antennas

onto the connectors

WLAN 1 Ant 1 / Ant 2 and

WLAN 2 Ant 1 / Ant 2.

The desired MIMO behaviour can

be congured under

> Physical WLAN Settings

> Radio

> Antenna grouping

a

WLAN 1 Ant 1

WLAN 1 Ant 2

WLAN 2 Ant 1

WLAN 2 Ant 2

a

*) The additional power LED status are displayed in 5-seconds rotation if the device is congured to be managed by the

LANCOM Management Cloud.

Product specificaties