La Crosse Technology WS-8054U Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor La Crosse Technology WS-8054U (24 pagina's) in de categorie Thermometer. Deze handleiding was nuttig voor 70 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/24
Model : WS-8054U
433 MHz
Radio Controlled Temperature Alarm
Instruction Manual
R A D I O C O N T R O L L E D
SET
ALARM
OUTDOORINDOORDATE
+
TIME
FCC ID: OMO-01RX (receiver),
OMOTX6U (transmitter)
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC
RU L ES. O P E RAT IO N IS SUBJ EC T TO T HE
FOLLOWING TWO CONDITIONS:
1. THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE, AND
2. THIS DEVICE MUST ACCEPT INTERFERENCE
RECEIVED, INCLUDING INTERFERENCE THAT
MAY CAUSE UNDESIRED OPERATION.
R
Contents
Language Page
English 2
French 44
Spanish 88
TABLE OF CONTENTS
Topic Page
Inventory of Contents/ Additional Equipment 4
About WWVB 4
Quick Set-Up Guide 6
Detailed Set-Up Guide
Battery Installation 8
Program Mode
Function Buttons 14
Time Zone Setting 15
DST (Daylight Saving Time) Setting 16
Language Selection 17
Time Setting 18
Calendar Setting 20
12/24-Hour Setting 21
Selecting ËšF or ËšC 22
Features & Operations
Changing Display Mode (viewing seconds)
23
The Alarm 24
Indoor temperature 27
Remote Temperature 27
E.L. backlight 28
Mounting 28
Maintenance & Care 31
Troubleshooting 32
Specications 35
Warranty Information 36
GB
P.3
GB P.2
INVENTORY OF CONTENTS
1) WS-8054U
2) TX6U remote temperature transmitter
3) Instruction manual and warranty card.
ADDITIONAL EQUIPMENT (not included)
1) Two fresh 1.5V AA batteries.
2) Two fresh 1.5V AA batteries.
3) Three wall-hanging screws.
4) Appropriate screwdriver for screws.
ABOUT WWVB (Radio Controlled Time)
The NIST (National Institute of Standards and
Technology-Time and Frequency Division) WWVB radio
station is located in Ft. Collins, Colorado, and transmits
the exact time signal continuously throughout the United
States at 60 kHz. The signal can be received up to 2,
000 miles away through the internal antenna in the
Temperature Alarm. However, due to the nature of the
Earth's Ionosphere, reception is very limited during
daylight hours. The Temperature Alarm will search for a
signal every night when reception is best. The WWVB
radio station derives its signal from the NIST Atomic clock
in Boulder, Colorado. A team of atomic physicists is
continually measuring every second, of every day, to an
accuracy of ten billionths of a second per day. These
physicists have created an international standard,
measuring a second as 9,192,631,770 vibrations of a
Cesium-133 atom in a vacuum.
QUICK SET-UP GUIDE
Hint
: Use good quality Alkaline Batteries and avoid
rechargeable batteries.
1. Have the temperature clock and remote temperature
sensor 3 to 5 apart.
2. Batteries should be out of both units for 10 minutes.
3. Place the batteries into the remote temperature
sensor first then into the temperature clock.
(All remote temperature sensors must be started
before the temperature clock)
4. DO NOT PRESS ANY BUTTONS FOR 10 MINUTES.
In this time the temperature clock and remote
temperature sensor will start to talk to each other and
the temperature clock will show both the indoor
temperature and an outdoor temperature. If the
temperature clock does not display both temperatures
after the 10 minutes please retry the set up as stated
above. After both indoor and outdoor temperatures are
displayed for 10 minutes you can place your remote
temperature sensor outdoors and set your time.
The remote temperature sensor should be placed in a
dry, shaded area. The remote temperature sensor has
a range of 80 feet. Any walls that the signal will have to
pass through will reduce distance. An outdoor wall or
window will have 20 to 30 feet of resistance and an interior
wall will have 10 to 20 feet of
resistance. Your distance
plus resistance should not exceed 80 ft. in a straight line.
NOTE
: Fog and mist will not har m your remote
temperature sensor but direct rain must be avoided.
To complete the set up of your temperature clock after
the 10 minutes have passed please follow the steps
below.
DETAILED SET-UP GUIDE
I) BATTERY INSTALLATION
Note
: To avoid start-up problems make sure that the
batteries do not spring free.
A) REMOTE TEMPERATURE SENSOR
1) Remove the battery cover.
2) Observing the correct polarity, install 2 AA batteries.
The batteries will fit tightly (to avoid start-up problems
make sure that they do not spring free during
installation).
3) Replace the battery cover.
SIZE AA LR6
SIZE AA LR6
Temp. Transmitter
433 MHz
GB
P.5
GB P.4
GB
P.7
GB P.6
GB
P.9
GB P.8
B) TEMPERATURE ALARM
1) Remove the battery cover, located on the backside
of the unit.
2) Observe the correct polarity and install 2 AA batteries.
3) Replace the battery cover.
Note
: After the batteries have been installed a tone
will sound, and all the LCD's (Liquid Crystal Display) will
briefly light up. The indoor temperature, the date as "1/
1", the weekday as "MON", and the remote temperature
will be displayed (within three minutes). Also, the time
will appear as "-:--" for approximately 1 minute.
TheWWVB search is automatically initiated, and a tower
icon appears and flashes with the time colon (no tower
icon will appear if the WWVB is too weak to be detected,
and the time display will remain on "-:--"). While the
WWVB search is being conducted various numbers will
appear in the time display. After 10minutes, the
temperature alarm will either display the WWVB time,
or discontinue the search if the time is not found. If the
search is cancelled "-:--" will appear in the time LCD.
The temperature alarm will conduct a WWVB search
every hour until the first signal is found. Once the WWVB
time is found, a search is automatically conducted nightly
at midnight. If the signal is found at midnight, the tower
icon will remain, if not, another search will take place
every hour (until 6:00 am) until the signal is found
successfully. If no signal is found during this period, the
tower icon will not appear and the clock will search again
at 12:00 am the next night.
PROGRAM MODE
To enter the program mode hold down the "SET" button
for 2 seconds, until "-5EST" flashes in the date LCD.
The program mode is laid out in a manner that allows
you to program each function separately, or you can
follow the instructions entirely to program the temperature
alarm. Complete programming is usually done for the
initial set-up, and will require you to skip step 1 of
programming sections III through VIII. Press the
"SNOOZE" button at any time to exit the program mode,
or wait approximately 15
seconds for the temperature
alarm to automatically return to normal operation.
I) FUNCTION BUTTONS
There are 3 function buttons located on the front of the
temperature alarm and one on the top. The function
buttons are labeled:"SET", "+", "ALARM", and "SNOOZE"
(the top bar).
II) TIME ZONE SETTING
1) Hold down the "SET" button for 2 seconds, the default
setting "-5EST" will ash in the date LCD.
2) Press and release the "+" button to select the
appropriate time zone. There are 13 time zones to
choose from:
R A D I O C O N T R O L L E D
SET
ALARM
OUTDOORINDOORDATE
+
TIME
TIME
ALARM
SNOOZE
WWVB Radio reception
Alarm
Icon
WWVB
Time
Date
Weekday or
seconds display
Indoor temperature
or seconds display
Outdoor
temperature
+
S I Z E A A
+
S I Z E A A
-4ATL Atlantic Time
-5EST Eastern Time (default setting)
-6CST Central Time
-7MST Mountain Time
-8PST Pacific Time
-9ALA Alaskan Time
-10HAW Hawaiian Time
-11, -12
Next tow time zones West of HAW
GMT Greenwich Mean Time
-1, -2, -3GMT Three time zone West of GMT
GB
P.11
GB P.10
GB
P.13
GB P.12
GB
P.15
GB P.14


Product specificaties

Merk: La Crosse Technology
Categorie: Thermometer
Model: WS-8054U

Heb je hulp nodig?

Als je hulp nodig hebt met La Crosse Technology WS-8054U stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Thermometer La Crosse Technology

Handleiding Thermometer

Nieuwste handleidingen voor Thermometer