Kramer SWT3-22-HU-WP-T-EU/UK Handleiding

Kramer Schakelaar SWT3-22-HU-WP-T-EU/UK

Bekijk gratis de handleiding van Kramer SWT3-22-HU-WP-T-EU/UK (3 pagina’s), behorend tot de categorie Schakelaar. Deze gids werd als nuttig beoordeeld door 2 mensen en kreeg gemiddeld 4.3 sterren uit 1.5 reviews. Heb je een vraag over Kramer SWT3-22-HU-WP-T-EU/UK of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Download PDF

Pagina 1/3

SWT3 WP- - -22 HU -T- EU/UK Quick Start

P/N:

2900- 301854QS

Rev:

Scan for full manual

SWT3- - -WP-T-EU/UK 22 HU Quick Start Guide

This guide helps you install and use your SWT3- -22 HU-WP-T-EU/UK for the first time.

Go to http://www.kramerav.com/downloads/SWT3 22- -HU- -T-WP EU/UK to download the latest user manual

and check if firmware upgrades are available.

Step 1: Check what’s in the box

SWT3 WP- - -22 HU -T-EU /UK 2x2 4K60 USB-

C/HDMI Wall-plate Switcher Transmitter

1 Multi signal USB- C cable (1m)

Front panel

1 Power adapter and cord

1 Quick start guide

1 Screw set

Step 2: -Get to know your SWT3 22- - -T- HU WP EU/UK

# Feature Function

1 1 IN Button (USB- Press C) to select USB-C input port.

Button LED white when active signal is detected.

2 2 IN Button (HDMI, USB-C Host) Press to select HDMI port. Press to toggle between the HDMI and Host ports. Button

LED lights white when active signal is detected.

3 STATUS LED Lights green when there is an HDBT link and active input signal.

DISPLAY ON

Button

Press to toggle the remote display on or off.

The button LED lights white when remote display power is on.

5 1 IN

USB-C Connector

Connect to USB- ): C Host (AV sources + USB + LAN

• that supports DisplayPort Alternate Mode, (for example, a laptop) to share

content.

• to connect to the LAN, using your USB- d C wire connection.

• to charge the connected sources (that supports USB Power Delivery 2.0).

While charging, the charging icon (to the right of the connector) becomes

visible and lights orange.

IN 2

HDMI Connector

Connect to a compatible HDMI display.

USB-C Host

Connect to a USB-C host (for example, a room PC).

USB DEVICE Connect to the USB local peripheral devices (for example, a USB camera, a soundbar,

microphone, keyboard & mouse).

HDBT OUT

# Feature Function

USB A 3.1 Connector 1 & 2

8 OUT HDMI

Connect to a compatible HDMI display.

9 HDBT OUT

RJ- 45 Connector

Connect to the HDBT IN RJ- 45 connector on a

receiver (for example, EXT3 XR- -POE - R).

10 LAN 1G RJ- 45 Connector Connect to a LAN to provide Network and Internet to the source device that is

connected to the USB C IN port, and/or Ethernet extension to the receiver.-

11 GND Grounding Screw Ring Tongue

Terminal

Connected to grounding wire.

12 AUDIO OUT 5- pin Terminal Block

Connector

Connect to a balanced stereo analog audio acceptor.

13 2- I/O pin Terminal Block Connect to:

• Input- triggering devices (for example, remote buttons or sensors), OR

• Output triggered- devices (for example, remote alarm LED indication).

These GPIO ports may be configured as a digital input, digital output, or analog input

ports.

14 - 3- RS 232 pin Terminal Block

Connector

Connect to - an RS 232 controlled device (for example, the connected PTZ USB

camera) to be controlled via an IP- connected controller (for example, SL-240C).

15 19/20V DC Use the included 19V 6A power supply for powering the unit and charging the source

device connected to the USB-C port.

Step 3: Install the SWT3-22- - -T- HU WP EU/UK

Insert the device into the in wall box (note that first you need to connect the-

HDBT cable and power) and connect the parts as shown in the illustration below:

When installing the device, take care not to obstruct the upper and lower ventilation holes.

• 2 EU: gang in- wall junction box, with a - cut hole diameter of 2x68mm and depth that can fit in both the device and the

connected cables (DIN 49073).

• UK: 2 gang in-wall junction box (BS 4662), 135x75mm (W, H) and depth that can fit in both the device and the

connected cables.

Ventilation Holes

Step 4: Connect inputs and outputs

Always switch OFF the power on before each device connecting it to - - - -T- . your SWT3 22 HU WP EU/UK

Step 5: Connect power

Connect the power adapter to the SWT3- - - -T 22 HU WP and the power cord and plug it into the mains electricity.

Safety Instructions (See www.kramerav.com for updated safety information)

Caution:

• There are no operator serviceable parts inside the unit.

• For products with relay terminals \O and GPI ports, please refer to the permitted rating for an external connection, located next to the

terminal or in the User Manual.

Warning:

• Use only the power cord that is supplied with the unit.

•

Disconnect the power and unplug the unit from the wall before installing.

The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.

Transmitter Side

Laptop

USB-C

Eth

USB

NUC/

RoomPC

HDMI

Keyboard

Mouse

USB

Display