Kenwood KMM-BT408 Handleiding

Kenwood Receiver KMM-BT408

Lees hieronder de 📖 handleiding in het Nederlandse voor Kenwood KMM-BT408 (30 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 20 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/30
B5A-3850-00 [MN]Š 2022 JVCKENWOOD Corporation
KMM-BT408
KMM-BT208
DIGITAL MEDIA RECEIVER
INSTRUCTION MANUAL
ENGLISH 3
Before Use
IMPORTANT
• To ensure proper use, please read through this manual before using this
product. It is especially important that you read and observe Warnings and
Cautions in this manual.
• Please keep the manual in a safe and accessible place for future reference.
WARNING
• Do not operate any function that takes your attention away from safe
driving.
• Do not ingest the battery, Chemical Burn Hazard.
The remote control supplied with this product contains a coin/button cell
battery.
If the coin/button cell battery is swallowed, it can cause severe internal
burns in just 2 hours and can lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the
product and keep it away from children.
If you think batteries might have been swallowed or placed inside any part
of the body, seek immediate medical attention.
CAUTION
Volume setting:
• Adjust the volume so that you can hear sounds outside the car to prevent
accidents.
• Lower the volume before playing digital sources to avoid damaging the
speakers by the sudden increase of the output level.
General:
• Avoid using the external device if it might hinder safe driving.
• Make sure all important data has been backed up. We shall bear no
responsibility for any loss of recorded data.
• Never put or leave any metallic objects (such as coins or metal tools) inside
the unit to prevent a short circuit.
• USB rating is indicated on the main unit. To view, detach the faceplate.
(Page 4)
• Depending on the types of cars, the antenna will automatically extend
when you turn on the unit with the antenna control wire connected
(page28). Turn off the unit or change the source to STANDBY when
parking at a low ceiling area.
Remote control (RC-406):
• Do not leave the remote control in hot places such as on the dashboard.
• Risk of fire or explosion if the battery is replaced by an incorrect type.
Ensure to replace only with the same type.
• Risk of fire, explosion or the leakage of flammable liquid or gas if the
battery is left in an extremely high temperature surrounding environment
and/or subjected extremely low air pressure. The battery pack or batteries
shall not be exposed to excessive heat such as sunshine, fire or the like.
• Risk of fire, explosion or the leakage of flammable liquid or gas if the
battery is disposed into fire or a hot oven, recharged, shorted, mechanically
crushed or cut of the battery.
• If spilled fluid comes in contact with your eyes or on clothing, immediately
rinse with water and consult a physician.
6 ENGLISH
Getting Started
2 Set the clock and date
1 Press the volume knob to enter
[FUNCTION]
.
2 Turn the volume knob to select
[CLOCK]
, then press the knob.
To adjust the clock
3 Turn the volume knob to select
[CLOCKADJUST]
, then press the knob.
4 Turn the volume knob to make the settings, then press the knob.
Set the time in the order of “Hour” “Minute”.
5 Turn the volume knob to select
[CLOCK FORMAT]
, then press the knob.
6 Turn the volume knob to select
[12H]
or
[24H]
, then press the knob.
To set the date
7 Turn the volume knob to select
[DATEFORMAT]
, then press the knob.
8 Turn the volume knob to select
[DD/MM/YY]
or
[MM/DD/YY]
, then press
the knob.
9 Turn the volume knob to select
[DATESET]
, then press the knob.
10 Turn the volume knob to make the settings, then press the knob.
Set the date in the order of “Day” “Month” “Year” or “Month” “Day”
“Year”.
11 Press and hold to exit.
To return to the previous setting item, press .
3 Set the other optional settings
You can only set the following items while the unit is in STANDBY source.
1 Press SRC repeatedly to enter STANDBY.B
2 Press the volume knob to enter
[FUNCTION]
.
3 Turn the volume knob to select an item (see the following table), then
press the knob.
4 Repeat step 3 until the desired item is selected or activated.
5 Press and hold to exit.
To return to the previous setting item, press .
Default: [XX]
[AUDIO CONTROL]
[SWITCH PREOUT] (For )
(Applicable only if is set to .) (Page 7)[X’OVER] [2WAY]
[REAR]/[SUB-W]: Selects whether rear speakers or a subwoofer are
connected to the line out terminals on the rear (through an external
amplifier). (Page 29)
[DISPLAY]
[EASY MENU] (For )
When entering ...[FUNCTION]
[ON] [ZONE 1]: illumination changes to white color. ;
[OFF] [ZONE 1] [COLOR SELECT]: illumination remains as color.
(Page 25)
• illumination changes to light blue color when you enter [ZONE 2]
[FUNCTION] [EASY MENU], irregardless of the setting.
• Refer to the illustration on page 24 for zone identification.
[TUNER SETTING]
[PRESET TYPE] [NORMAL]: Memorizes one station for each preset button in each band
(FM1/FM2/FM3/AM/SW1/SW2). ; : Memorizes one station for [MIX]
each preset button, regardless of the selected band.


Product specificaties

Merk: Kenwood
Categorie: Receiver
Model: KMM-BT408

Heb je hulp nodig?

Als je hulp nodig hebt met Kenwood KMM-BT408 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Receiver Kenwood

Handleiding Receiver

Nieuwste handleidingen voor Receiver