Jung DWPM K 360 WW Handleiding

Jung Smarth home DWPM K 360 WW

Lees hieronder de 📖 handleiding in het Nederlandse voor Jung DWPM K 360 WW (18 pagina's) in de categorie Smarth home. Deze handleiding was nuttig voor 22 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/18

Motion and presence detector

Light Management

Motion and presence detector

Art. No. : DWPMK360WW

Motion and presence detector

Art. No. : DWPMK360AL

Operating instructions

1 Safety instructions

Electrical devices may only be mounted and connected by electrically skilled persons.

Serious injuries, fire or property damage possible. Please read and follow manual fully.

Danger of electric shock. Device is not suitable for disconnection from supply voltage.

Danger of electric shock. Always disconnect before carrying out work on the devise or

load. In so doing, take all the circuit breakers into account, which support dangerous

voltages to the device and or load.

Do not press on the sensor window. Device can be damaged.

Keep button cells out of reach of children! If button cells are swallowed, get medical help

immediately.

Risk of explosion! Do not throw batteries into fire.

Risk of explosion! Do not recharge batteries.

The device is not suitable for use as a burglar alarm or other alarm.

These instructions are an integral part of the product, and must remain with the end

customer.

2 Device components

Figure 1

(1) Connection box

(2) Sensor top

(3) Brightness sensor

(4) Sensor window with red and blue display LED

(5) Decor ring

(6) Push-on cover

1/18

82593213

J0082593213 12.01.2017

Figure 2

(7) IR end customer remote control, included in the scope of delivery

(8) IR installation engineer remote control (see Accessories)

3 Function

Intended use

- Automatic switching of lighting depending on the heat motion and ambient brightness.

- Indoor ceiling mounting, surface-mounted

Product characteristics

- 2-point light control

- Functions settable with IR remote controls

- Restriction of the detection field by switching off individual sensors or push-on cover.

- Operation with IR remote control, 2-wire extension or installation button

- Teach function for adjustment of the brightness threshold, in combination with IR remote

controls

- Switch-off warning

- Short-time operation, e.g. to activate acoustic signal encoders

- Display LEDs

- Presence simulation

- Function as twilight switch

- Dynamic run-on time

- Extension of the detection area through parallel switching of multiple devices

i The extension of the detection area with 3-wire extensions is not possible.

Automatic operation

The device detects heat motions of people, animals and objects.

- The light is switched on if a person enters the detection area and the brightness is below

the set threshold.

The run-on time restarts with each detected motion.

- The light is switched off when it is no longer required because:

No more movement is detected in the detection area and the run-on time has elapsed or

the ambient light is too bright.

The switch-off brightness is calculated from the set brightness threshold and the connected

light.

To avoid brief shading from causing switch-off, switch-off only takes place when the set

run-on time has elapsed. The run-on time does not restart on movement detection for as

long as the switch-off brightness is exceeded.

i The minimum switch-off brightness is 100 lux, even if a lower value is set.

2/18

82593213

J0082593213 12.01.2017

Light Management

Motion and presence detector

To avoid any switch-on caused by a cooling illuminant, no movement signals are evaluated for

a brief lockout time after switching off. The motion detector adjusts itself to the ambient

conditions to keep the time as short as possible.

Short time operation

If movement occurs, then a short pulse of approx. 0.5 seconds is triggered according to the

brightness. The pulse is cyclically repeated as long as motions are detected.

Switch-off warning

If the switch-off warning is active, the light is not switched off immediately after the run-on time

has elapsed. Triple flashing at an interval of 10 seconds shows that the light will be switched off

soon. The run-on time is thereby prolonged by approx. 30 seconds. If movement is detected

during the switch-off prewarning, then the run-on time is restarted and the light remains on.

Dynamic run-on time

The function determines a run-on time within specified limits automatically and dynamically from

detected movements. In so doing, the run-on time is increased if presence continues or

decreased if absence is detected.

Presence simulation

In automatic operation, the motion detector continuously saves times for which the lighting was

switched on. A maximum of 60 switching operations are saved over a period of 24 hours. If

more switching operations take place, the oldest ones are overwritten respectively. If the

presence simulation is activated, the motion detector switches the lighting at the saved times

according to the brightness. Switch-off takes place after the run-on time has elapsed. Detected

motions prolong the run-on time or the light is switched on depending on brightness. Times are

not saved.

Function as twilight switch

The function is active as soon as all the PIR sensors have been switched off (see

Commissioning). The light is switched according to the brightness. Motions are not evaluated

- The light is switched on if the brightness is below the set threshold for 4 minutes.

- The light is switched off when the switch-off brightness (see Automatic mode) is exceeded

for 4 minutes.

i Switch-on and switch-off of the light via 2-wire extensions or installation buttons is not

possible. The Continuous on/off and on/off for 2 hours functions cannot be used.

Behaviour after mains return

After mains return, the device performs a self-test for a maximum of 20 seconds. After the self-

test has been completed, the device is ready for operation. The device switches the light

according to the settings made.

The following applies during the self-test:

- The red and blue display LEDs (4) light up.

- The device cannot be operated or set using an IR remote control.

- Movements are not detected.

- The device can be switched via 2-wire extensions or installation buttons.

4 Operation

Special functions can be switched and settings adjusted using the supplied IR remote control.

i Special functions can restrict operation via the 2-wire extension inserts or installation

buttons.

i If multiple devices are within the range of the IR remote control, then align it so that only

the device to be operated can receive the signals.

LED display

Behind the sensor window (4) are a red and a yellow LED (Figure 1) for indicating different

states of operation.

Red LED Blue LED Signalling

3/18

82593213

J0082593213 12.01.2017

Light Management

Motion and presence detector

Product specificaties

Merk:	Jung
Categorie:	Smarth home
Model:	DWPM K 360 WW
Kleur van het product:	Wit
Hoogte:	66 mm
Stroombron:	AC
Connectiviteitstechnologie:	Bedraad
Diameter:	103 mm
Ondersteund aantal accu's/batterijen:	1
Ingangsspanning:	110 - 230 V
Frequentie:	50 / 60 Hz
Maximale afstand:	100 m
Bedrijfstemperatuur (T-T):	-5 - 45 °C
Batterijtechnologie:	Lithium
Type batterij:	CR2025
Detectie hoek:	360 °
Detectieafstand:	20 m
Gemeten parameters:	Light, Temperature
Helderheid meetbereik ( binnen):	5 - 2000 Lux