Jung 1792HTBT Handleiding

Jung Niet gecategoriseerd 1792HTBT

Bekijk gratis de handleiding van Jung 1792HTBT (5 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 5 mensen en kreeg gemiddeld 4.9 sterren uit 3 reviews. Heb je een vraag over Jung 1792HTBT of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Download PDF

Pagina 1/5

LB management

LB managementLB management

Brightness / temperature sensor Bluetooth

Brightness / temperature sensor BluetoothBrightness / temperature sensor Bluetooth

Art. no.: 1792HTBT

Operating instructions

Operating instructionsOperating instructions

11 Battery safety instructions

Battery safety instructions

Battery safety instructionsBattery safety instructions

This device or its accessories are supplied with batteries in the form of button cells.

DANGER! Batteries can be swallowed. This can lead directly to death by suffocation. Danger-

DANGER! Batteries can be swallowed. This can lead directly to death by suffocation. Danger-DANGER! Batteries can be swallowed. This can lead directly to death by suffocation. Danger-

ous substances may cause severe internal burns leading to death within 2 hours.

ous substances may cause severe internal burns leading to death within 2 hours.ous substances may cause severe internal burns leading to death within 2 hours.

Keep new and used batteries away from children.

Do not use devices if the battery compartment does not close securely and keep away from

children.

If you suspect that a battery has been swallowed or is in any orifice of the body, seek immediate

medical attention.

WARNING! Improper handling of batteries can result in explosion, fire or chemical burn due to

WARNING! Improper handling of batteries can result in explosion, fire or chemical burn due toWARNING! Improper handling of batteries can result in explosion, fire or chemical burn due to

leakage.

leakage.leakage.

Do not heat or throw batteries into fire.

Do not reverse polarity, short-circuit or recharge batteries.

Do not deform or disassemble batteries.

Replace batteries only with an identical or equivalent type.

Remove empty batteries immediately and dispose of in an environmentally friendly manner.

These instructions are an integral part of the product, and must remain with the end customer.

These instructions are an integral part of the product, and must remain with the end customer.These instructions are an integral part of the product, and must remain with the end customer.

22 Intended use

Intended use

Intended useIntended use

– Sensor for detecting brightness and temperature

– Operation with Bluetooth universal timer from LB management

– Adhesive mounting in the interior on windows

33 Commissioning

Commissioning

CommissioningCommissioning

Open the housing

Open the housingOpen the housing

Figure1: Open the housing

￭ Open the housing by pushing it apart. To do so, insert a thin slotted screwdriver into the

opening recess (Figure 1) and raise it up so that two catches are passed.

1 / 5

82599913 11.11.2019

J0082599913

LB management

LB managementLB management

Brightness / temperature sensor Bluetooth

Figure2: Raise housing lid

￭ Push the housing apart as far as it will go.

￭ To remove the cover, it must first be lifted off on one side, e.g. with a small screwdriver

(Figure 2).

Figure3: Removing the circuit board

￭ Remove the circuit board. To do this, carefully push the two locking lugs (Figure 3) out-

wards so that the board can be lifted up.

Inserting the battery

Inserting the batteryInserting the battery

Obey the battery safety instructions.

￭ Keep contacts of batteries and device free of grease.

Figure4: Inserting the battery

￭ Slide battery into battery holder (Figure 4). Observe polarity: the positive pole of the bat-

tery must be at the top.

2 / 5

82599913 11.11.2019

J0082599913

LB management

LB managementLB management

Brightness / temperature sensor Bluetooth

Figure5: Engaging the circuit board

￭ Note MAC address (3) (Figure 5). This address is required for assignment to the cover.

￭ Insert the circuit board in the housing base. Firstly, push the circuit board up to the front

side of the housing and then push the rear section of the circuit board downwards

(Figure 5).

Figure6: Close housing

￭ Reattach the housing lid and push the housing together until it locks into place. (Figure 6).

The device is ready for operation.

Assigning the sensor to the cover

Assigning the sensor to the coverAssigning the sensor to the cover

The sensor transmits the brightness and temperature values every 5 minutes and when the

brightness or temperature changes. The sensor must be assigned to the cover so that it can

process the measured values of the sensor. This assignment is done via the app.

￭ Select "Add sensor" in the app configuration.

An input field for the MAC address of the device will appear in the app.

￭ Enter the MAC address (3) in the input field.

The actuator will now evaluate all received sensor telegrams.

44 Mounting

Mounting

MountingMounting

Remove empty batteries immediately and dispose of in an environmentally friendly

Remove empty batteries immediately and dispose of in an environmentally friendlyRemove empty batteries immediately and dispose of in an environmentally friendly

manner. Do not throw batteries into household waste. Consult your local authorities

manner. Do not throw batteries into household waste. Consult your local authoritiesmanner. Do not throw batteries into household waste. Consult your local authorities

about environmentally friendly disposal. According to statutory provisions, the end

about environmentally friendly disposal. According to statutory provisions, the endabout environmentally friendly disposal. According to statutory provisions, the end

consumer is obligated to return used batteries.

consumer is obligated to return used batteries.consumer is obligated to return used batteries.

Selecting installation location

Selecting installation locationSelecting installation location

To ensure good transmission quality, keep a sufficient distance from any possible sources of in-

terference, e.g. metallic surfaces, microwave ovens, hi-fi and TV systems, ballasts or trans-

formers.

3 / 5

82599913 11.11.2019

J0082599913