Juki AK-121 Handleiding

Juki Naaimachine AK-121

Lees hieronder de 📖 handleiding in het Nederlandse voor Juki AK-121 (2 pagina's) in de categorie Naaimachine. Deze handleiding was nuttig voor 36 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
1.
ミシンの窓板を取りはずし、ひざ上げ横棒段ね
じ を付属のひざ上げ横棒ピン と交換します。❶ ❷
1.
Remove the window plate of the machine, and
replace the knee lifter connecting rod hinge screw
with the attached knee lifter connecting rod pin
.
自動押え上げ装置
Auto Lifter
AK-121
取扱説明書 /INSTRUCTION MANUAL
この度は、窓板取り付けタイプ自動押え上げ装置を、お買い上げいただきましてありがとうございます。
この装置は、主な特徴として、1)取り付けが簡単、2)ひざ上げ装置と併用できる、などがあります。ご使
用の前にかならずこの取扱説明書をお読みになり、末永くご愛用くださいますようお願い申しあげます。
We heartily appreciate your buying JUKI’s window plate mounting type Auto lifter.
The main features of this equipment are as follws ; 1) Simple installation, 2) Available together with the knee lifter
We recommend you to read these instructions before use, and we hope you will use it for a long time.
取り付け手順 /INSTALLATION
2. AK 装置(組) をミシンに取り付けます。
時、ク のが、
げ横棒 にセットされるように取り付けます。
2. Install the AK device on the machine.
At this time, install it so that the slot of solenoid link
may be set on the knee lifter connecting rod pin .
3. AK 装置(組) をねじ止めします。
3. Tighten the AK device with screws.
No.02
29342508
4.
ソレノイド(組)からの白コネクタ 2P コード
B よ
クランプ d、e、f に通し CN4 に差し込みます。
4. Pass white connctor 2P cord coming from the
solenoid asm. through cord clamps d, e and f from
hole B in the control box and insert it into CN4 .
5. 付属の・バ で、ネル
ドが、可動部に接触しないようにします。
5. Make sure that the operation panel cord cannot
contact the moving part by using the attached cord
band .
押え上げ高さの調整 /ADJUSTING THE AUTO-LIFTER STROKE
ドライバー でソレノイド軸を回転させ、6 角レA
ンチ で抱きねじを締めます。B
Turing the solenoid shaft by using driver A, tighten the
clamp screw by using hexagonal wrench key B.
主な仕様 /SPECIFICATIONS
◦ 押え上昇量6mm(標準 / Presser foot lifting amount : Standard 6 mm
◦ 最大押え圧58.8N / Max. presser foot pressur : 58.8N
※ 電源電圧 100% / At 100%
なお、本説明書は、当社 SC-905 をもとに書かれております。
他社モータを使用される場合は、モータの取扱説明書をお読みの上、配線くださるようお願い申しあげます。
また、ミシンからオペレータが離れる場合は、必ずスイッチを切ってください。
In addition, this instruction book is made in accordanca with the SC-905 of JUKI motors.
When using motors of other suppliers, we recommend you to carry out wiring after reading the instruction book of motors.
When an operator leaves from the machine, make sure to turn off the power.
B
A
10 · 10 Printed in Japan
INDUSTRIAL SEWING MACHINE DIVISION
2-11-1, TSURUMAKI, TAMA-SHI,
TOKYO, 206-8551, JAPAN
PHONE : (81)42-357-2371
FAX : (81)42-357-2274
http://www.juki.com
Copyright © 2000 - 2010 JUKI CORPORATION
本書の内容を無断で転載、複写することを禁止します。
All rights reserved throughout the world.
工業用ミシン事業部
〒 206-8551東京都多摩市鶴牧 2-11-1
TEL.042-357-2371(ダイヤルイン)
FAX.042-357-2274
http://www.juki.co.jp この製品の使い方について不明な点がありましたらお求めの販売店又は当社営業所にお問い合わせください。
※この取扱説明書は仕様改良のため予告なく変更する事があります。
Please do not hesitate to contact our distributors or agents in your area for further information when necessary.
*
The description covered in this instruction manual is subject to change for improvement of the
commodity without notice.
CN4


Product specificaties

Merk: Juki
Categorie: Naaimachine
Model: AK-121

Heb je hulp nodig?

Als je hulp nodig hebt met Juki AK-121 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Naaimachine Juki

Handleiding Naaimachine

Nieuwste handleidingen voor Naaimachine