JBL SUB150P Handleiding

JBL Subwoofer SUB150P

Lees hieronder de 📖 handleiding in het Nederlandse voor JBL SUB150P (4 pagina's) in de categorie Subwoofer. Deze handleiding was nuttig voor 51 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4

Included Items

Your new JBL® SUB150P 300-watt powered subwoofer incorpo-

rates a 10" (250mm) PolyPlas™ cone transducer and a built-in

high-performance 300-watt (RMS) amplifier that deliver the power-

ful, dynamic and accurate low-frequency performance that makes

your film soundtracks and music come alive. And with line-level

and LFE inputs, adjustable crossover and phase controls and

automatic turn on/off, the SUB150P is also simple to connect and

set up.

We’re confident that this JBL subwoofer will provide every note of

enjoyment that you expect – and that when you think about pur-

chasing additional audio equipment for your home, car or office,

you will once again choose JBL products.

This quick-start guide contains all the information you need to set

up, connect and adjust your new subwoofer. For more in-depth

information, go to our Web site: www.jbl.com.

thank You For choosIng thIs JBl® Product

suB150P

300-Watt, 10" (250mm) Powered Subwoofer

quIck-start guIde

Phase Switch: This switch determines whether the subwoofer transduc-

er's piston-like action moves in and out in phase with the main speakers.

If the subwoofer were to play out of phase with the main speakers, the

sound waves from the main speakers could partially cancel out the sound

waves from the subwoofer, reducing bass performance and sonic impact.

This phenomenon depends in part on the placement of all the speakers

relative to the listening position and to each other in the room.

Input Mode Switch: When this switch is in the “Normal” setting, the input

signal from both Line In connectors is routed through the subwoofer's

built-in low-pass crossover network. When the switch is in the “LFE” set-

ting, the input signal from the LFE Input connector bypasses the subwoof-

er's built-in crossover network.

Volume Control: Use this control to adjust the subwoofer’s volume. Turn

the knob clockwise to increase the volume; turn the knob counterclock-

wise to decrease the volume.

Crossover Control: This control determines the highest frequency at

which the subwoofer reproduces sounds. The higher you set the Cross-

over control, the higher in frequency the subwoofer will operate and the

more its bass will “overlap” that of the satellite speakers. This adjust-

ment helps achieve a smooth transition of bass frequencies between the

subwoofer and the satellites for a variety of different rooms and subwoofer

locations.

NOTE: The Crossover Control functions only when the Input Mode switch

is in the “Normal” setting.

On/Standby LED: When the Power switch is in the “On” position, this

LED indicates whether the subwoofer is in the On or Standby state:

• When the LED glows green, the subwoofer is turned on.

• When the LED glows red, the subwoofer is in the Standby mode.

Line In/LFE Input Connectors:

• When you’re connecting the subwoofer to the dedicated subwoofer

output of a receiver/processor that has its own low-pass crossover

network, use the LFE Input connector and set the Input Mode switch

in the “LFE” position.

• When you're connecting the subwoofer to the preamp or subwoofer

outputs of a receiver/processor that does not have its own low-pass

crossover network, use both Line In connectors and set the Input

Mode switch in the “Normal” position. If your receiver/processor only

has one subwoofer output you can use either Line In connector.

Power Switch: Set this switch in the “On” position to turn the subwoofer

on. The subwoofer will then be in the Standby mode. It will automatically

turn On when an audio signal is detected at its inputs, and will return to the

Standby mode when no audio signal is detected its inputs after approxi-

mately 10 minutes.

If you will be away from home, or will not be using the subwoofer for an

extended period, set this switch in the “Off” position to conserve energy.

Power Cord Connector: After you have made and veriﬁed the subwoof-

er’s input connections, plug the female end of the supplied IEC power cord

into the subwoofer’s Power Cord connector, and plug the other end of the

power cord into an active, electrical outlet for proper opera-unswitched

tion of the subwoofer. plug the power cord into the accessory DO NOT

outlets found on some audio components.

suBwooFer rear-Panel controls and connectIons

2053 23

No rt hr id ge , CA USA

De sign ed and e n gi ne er ed i n USA

Made in P.R.C

SUB150P

Phase Switch

Input Mode Switch

Volume Control

Crossover Control

On/Standby LED

Power Switch

Line-Level/LFE

Input Connectors

Power Cord

Connector

www.jbl.com

English

PlacIng the suBwooFer

connectIng the suBwooFer

The performance of a subwoofer is directly related to its placement in the listening room

and its physical position relative to the other speakers in the system.

While it is true that in general our ears do not hear directional sounds at the low

frequencies where subwoofers operate, when installing a subwoofer within the limited

conﬁnes of a room, the reﬂections, standing waves and absorptions generated within

the room will strongly inﬂuence the performance of any subwoofer system. As a result,

the speciﬁc location of the subwoofer in the room does become important to the

amount and quality of bass that is produced.

For example, placing the subwoofer next to a wall generally will increase the amount of

bass in the room; placing it in a corner ( ) generally will maximize amount of bass in the 1

room. However, corner placement can also increase the destructive effect of standing

waves on bass performance. This effect can vary depending on the listening position

– some listening positions may yield very good results while others may have far too

much (or too little) bass at certain frequencies.

In many rooms, placing the subwoofer along the same plane as the left and right speak-

ers ( ) can produce the best integration between the sound of the subwoofer and that 2

of the left and right speakers. In some rooms, the best performance could even result

from placing the subwoofer behind the listening position ( ). 3

We strongly recommend that you experiment with placement before choosing a ﬁnal

location for your subwoofer. One way you can determine the best location for the sub-

woofer is by temporarily placing it in the listening position and playing music with strong

bass content. Move around to various locations in the room while the system is playing

(putting your ears where the subwoofer would be placed), and listen until you ﬁnd the

location where the bass performance is best. Place the subwoofer in that location.

Front Left

Speaker

Center

Speaker Front Right

Speaker

Surround Left

Speaker

Surround Right

Speaker

TO A RECEIVER OR PREAMP/PROCESSOR WITH A LOW-PASS FILTERED DEDICATED SUBWOOFER OUTPUT

TO A RECEIVER OR PREAMP/PROCESSOR WITH PREAMP OUTPUTS

SUBWOOFER

LFE OUT

205323

No rthridg e, CA USA

Designed an d engi neere d in USA

Made in P.R.C

SUB150P

PREAMP

OUTPUT

205323

No rthridg e, CA USA

Designed an d engi neere d in USA

Made in P.R.C

SUB150P

Receiver/Processor

Set Input Mode

Switch to “LFE”

Set Input Mode

Switch to “Normal”

Product specificaties

Merk:	JBL
Categorie:	Subwoofer
Model:	SUB150P
Kleur van het product:	Zwart
LED-indicatoren:	Stroom
Aan/uitschakelaar:	Ja
Type stroombron:	AC
Snelstartgids:	Ja
Microfoon, line-in ingang:	Nee
Stroomverbruik (in standby):	1 W
Equalizer-instellingen:	Nee
Gemiddeld vermogen subwoofer:	300 W
Diameter driver subwoofer (imperiaal):	10 "
Lijnuitgang:	Nee
Lijningang:	Ja
Handvat(en):	Nee
Subwoofertype:	Actieve subwoofer
Frequentiebereik subwoofer:	27 - 150 Hz
Breedte van de subwoofer:	441 mm
Hoogte van de subwoofer:	470 mm
Diepte van de subwoofer:	441 mm
Gewicht subwoofer:	18000 g
XLR in:	Nee
Afstandsbediening inbegrepen:	Nee
Tweeter:	Nee
Aantal subwoofers:	1
AC-ingangsspanning:	220 - 230 V
AC-ingangsfrequentie:	50 - 60 Hz
Stroomverbruik (typisch):	320 W
Diameter driver subwoofer:	250 mm
Subwoofer maximale vermogen:	500 W
Line inputs (RCA):	1
Crossover subwoofer frequenties:	50 - 150 Hz
Fase controle:	Ja
Down-firing:	Ja