Intermatic KPT0170 Handleiding

Intermatic Niet gecategoriseerd KPT0170

Bekijk gratis de handleiding van Intermatic KPT0170 (2 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 5 mensen en kreeg gemiddeld 4.5 sterren uit 3 reviews. Heb je een vraag over Intermatic KPT0170 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Download PDF

Pagina 1/2

Libertyville, Illinois 60048

www.intermatic.com

Power Tap Installation Guide

Intermatic KPT Series

SAFETY SECTION

Warning

Risk of Fire or Electric Shock

• Disconnect power at the circuit breaker(s) or disconnect switch before installing or servicing.

• Thoroughly read instructions before installing unit.

• The line voltage to the receptacle must be 120 VAC as indicated on the label of the Power Tap.

• Installation and/or wiring must be in accordance with national and local electrical code requirements

• Unused wire leads must be capped before installation.

• A photocontrol or shorting cap must be installed to ensure water does not enter Power Tap.

• Power Tap does not provide a ground connection. If device requires grounding, other provisions must be made to ensure proper grounding.

• Power Tap contains no serviceable parts.

PRODUCT DESCRIPTION

KPT0170 Power Tap

The Intermatic Model KPT0170 Power Tap is a receptacle that is used to tap into the electric power feed of a lighting ﬁxture

through its ANSI C136.10 (3-pin) or C136.41 (7-pin) style receptacle. The Power Tap meets all applicable requirements of

ANSI C136.10 and C136.41. It taps into the electrical power feed without disturbing the function of the light ﬁxture’s control

device. The Power Tap comes with a 16 AWG ﬂush cut cable end. The Power Tap contains no serviceable parts and is

intended for outdoor use.

Ratings:

• 120 VAC

• 15 A max total, 5 A max on line out

• 5 A from -40 °C to 50 °C, derate at 0.1 A/°C above 50 °C up to 70 °C max

• 50/60 Hz

POWER TAP INSTALLATION

Connect and Install an External Device

1. Connect the power feed cable from the Power Tap to the device per the manufacturer’s instructions for the device.

Note: The Power Tap does not provide a ground connection. If the device requires grounding, other provisions must be

made to ensure proper grounding.

2. Install the external device on the light pole or light pole arm as directed by the manufacturer of the device or by using the

device installation guidelines.

Power Tap Installation Guide

Install the Power Tap

1. Disconnect power at the circuit breaker(s) or disconnect the switch(es) before installing.

2. If present, remove the photocontrol or control node from the existing receptacle.

3. Insert the Power Tap into the receptacle by aligning the prongs on the Power Tap with the openings in the receptacle.

Push down on the Power Tap and twist clockwise to lock. The Power Tap must be locked in place.

4. Re-install the photocontrol, shorting cap, or control node device onto the Power Tap top receptacle.

5. Fasten the Power Tap cable to the light pole or light pole arm (per the regulations appropriate for your application) to

ensure the cable is secure and that no undue stress is placed on the receptacle and light ﬁxture.

6. Reconnect power at the circuit breaker(s), or reconnect the switch(es).

Photocontrol

KPT0170 Power pTa

Receptacle

Grounding

Wire

Properly secure cable

from Power pTa

Device

FIG. 1. Install Power Tap

LIMITED WARRANTY

Warranty service is available by either (a) returning the product to the dealer from whom the unit was purchased or (b) completing a warranty claim online

at www.intermatic.com. This warranty is made by: Intermatic Incorporated, Customer Service 1950 Innovation Way, Suite 300, Libertyville, IL 60048. For

warranty service go to: http://www.Intermatic.com or call 815-675-7000.

158--02200REF