Indesit IN2IE10CS80 Handleiding
Indesit
Vaatwasser
IN2IE10CS80
Bekijk gratis de handleiding van Indesit IN2IE10CS80 (24 pagina’s), behorend tot de categorie Vaatwasser. Deze gids werd als nuttig beoordeeld door 11 mensen en kreeg gemiddeld 4.8 sterren uit 6 reviews. Heb je een vraag over Indesit IN2IE10CS80 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/24
ENQuick Guide
1
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the dishes and on
the machine’s functional components.
• It is mandatory that THE SALT RESERVOIR NEVER BE EMPTY.
• It is important to set the water hardness.
The salt reservoir is located in the lower part of the dishwasher (see PROD-
UCT DESCRIPTION) and must be lled when the green oat on the cap of
the salt reservoir is no longer visible.
1. Remove the lower rack and unscrew the reservoir cap
(anticlockwise).
2. Only the rst time you do this: ll the salt reservoir
with water.
3. Position the funnel (see gure) and ll the salt reservoir
right up to its edge (approximately 1 kg); it is not unu-
sual for a little water to leak out.
4. Remove the funnel and wipe any salt residue away from the opening.
Make sure the cap is screwed on tightly, so that no detergent can get into
the container during the wash program (this could damage the water sof-
tener beyond repair).
Whenever you need to add salt, it is mandatory to complete the pro-
cedure before the beginning of the washing cycle to avoid corrosion.
WATER SOFTENING SYSTEM
Water softener automatically reduces water hardness, consequently prevent-
ing scale buildup on heater, contributing also to better cleaning eciency.
This system regenerates itself with salt, therefore it is required to rell
salt container when empty.
Frequency of regeneration depends on water hardness level setting - regen-
eration takes place once per 5 Eco cycles with water hardness level set to 3.
Regeneration process starts in nal rinse and nishes in drying phase, be-
fore cycle ends.
• Single regeneration consumes: ~3.5L of water;
• Takes up to 5 additional minutes for the cycle;
• Consumes below 0.005kWh of energy.
D
E
A
C
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DRYING easier. The rinse
aid dispenser A should be lled when when the
dark optical indicator on the dispenser door C be-
comes transparent.
NEVER pour the rinse aid directly into the
appliance tub.
FILLING THE DETERGENT DISPENSER
To open the detergent dispenser use the opening device D. Introduce the
detergent into the dry dispenser E only. Place the amount of detergent for
pre-washing directly inside the tub.
Usage of detergent not designed for dishwashers may cause malfunc-
tion or damage to the appliance.
Program
Programs description
Drying
phase
Duration
of wash
program
(h:min)
*)
Water
consumption
(litres/cycle)
Energy
consumption
(kWh/cycle)
1.
Eco 50°- Program is suitable to clean normally soiled tableware, that for this use, it is
the most ecient programme in terms of its combined energy and water consump-
tion, and that it is used to assess compliance with the EU Ecodesign legislation.
4:00 11.5 0.76
2.
Intensive 65° - Program recommended for heavily soiled crockery, especially suita-
ble for pans and saucepans (not to be used for delicate items).
2:30 15.5 1.50
3.
Mixed 55° - Mixed soil. For normally soiled dishes with dried food residues.
2:25 15.0 1.35
4.
Rapid 40’ 45° - Program to be used for half load of lightly-soiled dishes with no
dried food residues. Without drying.
-
0:40 8.0 0.90
5.
Push&GO 50° - Everyday wash and dry cycle that ensures great cleaning perfor-
mance in a short time without the need to pre-treat dishes.
1:20 11.0 1.10
CONTROL PANEL
FIRST TIME USE
More information in the Daily Reference Guide on website.
PROGRAMS TABLE
1. ON-OFF / Reset button with indicator light
2. Program selection button / Push&GO
3. Program indicator lights
4. START/Pause button with indicator light
PLEASE SCAN THE
QR CODE ON YOUR
APPLIANCE IN
ORDER TO HAVE
MORE DETAILED
INFORMATION
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2020.
Note for Test Laboratories:
For information on comparative EN testing conditions, please send an email to the following address:
dw_test_support@europeanappliances.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Values given for programs other than the program Eco are indicative only. The actual time may vary depending on many factors such as temperature and
pressure of the incoming water, room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and sensor cali-
bration. The sensor calibration can increase program duration up to 20 min.
1 2 4
3
THANK YOU FOR BUYING AN INDESIT PRODUCT.
In order to receive a more complete assistance, please
register your appliance on: www.indesit.com/register
Before using the appliance carefully read Safety and Installation Instructions.
After installation, please remember to remove all transport protection parts from
the dishwasher.
PUSH&GO
Push&GO button (P) is an easily distinguishable button that allows you direct access to the Push&GO program, a wash and dry cycle that ensures great
cleaning performance in a short time. You don’t have to worry which program to choose, Push&GO cycle will do the work for you.
To select Push&GO program, switch on appliance, press only P button for 3 seconds (corresponding indicator lights up) and close the door within 4 seconds.
Quick Guide
EN
2
In case your dishwasher doesn’t work properly, check if the problem can be solved by going through the following list. For other errors or issues
please contact authorized After-sales Service which contact details can be found in the warranty booklet. Spare parts will be available for a period
of either up to 7 or up to 10 years, according to the specic Regulation requirements.
PROBLEMS POSSIBLE CAUSES SOLUTIONS
The dishwasher does not ll
the water.
All LEDs are
blinking rapidly
No water in the water supply or the tap is closed.
Make sure there is water in the water supply or the tap running.
The inlet hose is bent.
Make sure the inlet hose is not bent (see INSTALLATION) reprogram
the dishwasher and reboot.
The sieve in the water inlet hose is clogged; it is
necessary to clean it
After having carried out the verication and cleaning, turn o
and turn on the dishwasher and restart a new program.
Dishwasher nishes the cycle
prematurely.
Drain hose positioned too low or siphoning
into home sewage system.
Check if end of drain hose is placed at correct height (see INSTALLA-
TION).Check for siphoning into home sewage system, install air admit-
tance valve if necessary.
Air in water supply. Check water supply for leaks or other issues letting air inside.
Detergent leaks.
Depends on the liquid detergent used and
can be emphasized in case of delay option is
activated.
Small leaks will not cause machine malfunction and can be avoided
by changing liquid detergent type or using tablets.
TROUBLESHOOTING
Please scan the QR code on your product in order to have more detailed information.
Policies, standard documentation, ordering of spare parts and additional product information can be found by:
• Using QR code on your product.
• Visiting our website docs.indesit.eu and parts-selfservice.europeanappliances.com
• Alternatively, contact our After-sales Service (See phone number in the warranty booklet).
When contacting our After-sales Service, please state the codes provided on your product’s identication plate.
The model information can be retrieved using the QR-Code reported in the energy label.
The label also includes the model identier that can be used to consult the portal of the registry at https://eprel.ec.europa.eu.
IEC 436
:
CLEANING THE FILTER ASSEMBLY CLEANING THE SPRAY ARMS
A
A
B
C
1 2 3
4
In case you nd foreign objects (such as broken glass, porcelain, bones, fruit seeds
etc.) please remove them carefully.
NEVER REMOVE the wash-cycle pump protection (black detail) (Fig 4).
To remove the upper spray arm,
turn the plastic locking ring in
aclockwise direction.
The lower spray arm may be
removed by pulling it upwards.
LOADING THE RACKS
CAPACITY: 10 standard place-settings
CARE AND MAINTENANCE
More information in the Daily Reference Guide on website.
UPPER RACK
Load delicate and light
dishes: glasses, cups, sa-
ucers, low salad bowls.
(loading example for the
upper rack)
FOLDABLE
FLAPS WITH
ADJUSTABLE
POSITION
LOWER RACK
For pots, lids, plates,
salad bowls, cutlery
etc. Large plates and
lids should ideally be
placed at the sides to
avoid interferences
with the spray arm.
(loading example for
the lower rack)
CUTLERY BASKET
The basket is equipped with
top grilles for improved cut-
lery arrangement. The cut-
lery basket should be posi-
tioned only at the front of
the lower rack.
Knives and other utensils
with sharp edges must be
placed in the cutlery basket with the points
facing downwards or they must be posi-
tioned horizontally in the tip-up compart-
ments on the upper rack.
Product specificaties
| Merk: | Indesit |
| Categorie: | Vaatwasser |
| Model: | IN2IE10CS80 |
Heb je hulp nodig?
Als je hulp nodig hebt met Indesit IN2IE10CS80 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Vaatwasser Indesit
15 Juni 2025
12 Mei 2025
27 April 2025
27 April 2025
27 April 2025
27 April 2025
13 Maart 2025
20 Februari 2025
15 November 2024
18 Augustus 2024
Handleiding Vaatwasser
- Orima
- Kubo
- Monogram
- Novy
- Infiniton
- Lamona
- Foster
- Continental Edison
- Nodor
- Neff
- Dometic
- Freggia
- Qilive
- Sharp
- Tomado
Nieuwste handleidingen voor Vaatwasser
18 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
16 Juni 2025
16 Juni 2025