I3International Am53 Handleiding
Bekijk gratis de handleiding van I3International Am53 (4 pagina’s), behorend tot de categorie Bewakingscamera. Deze gids werd als nuttig beoordeeld door 10 mensen en kreeg gemiddeld 4.4 sterren uit 5.5 reviews. Heb je een vraag over I3International Am53 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/4
User Manual
Thank you for purchasing i3 International’s Am53 High Definition indoor/outdoor analog
dome camera. Your camera is equipped with a motorized vari-focal 2.7-13.5mm @ F1.2
lens. The lens can be controlled through IE interface of the i3 encoders/standalone DVRs, or
through SRX-Pro Server/VPC using camera’s built-in OSD menu.
SAFETY
When installing your Am53 camera be sure to avoid:
• excessive heat, such as direct sunlight or heating appliances
• contaminants such as dust and smoke
• strong magnetic fields
• moisture and humidity
• areas with mechanical vibrations
• fluorescent lamps or objects that reflect light and unstable light sources
• temperatures below -40°C (-40°F) and above 50°C (122°F)
POWER
This camera accepts DC12V and AC24V power.
Maximum power consumption: 9.7W.
Ensure the supplied voltage meets the power consumption requirements of this camera
before powering the camera on. Incorrect voltage may cause irreparable damage to the
video camera and will effectively void the camera warranty.
CLEANING & SERVICING
For maximum optical clarity, the camera dome or lens must remain clean. Use a soft, dry
cloth to remove finger prints or dust from the dome cover.
• Use a blower to remove dust from the lens.
• Do not use volatile solvents such as alcohol, benzene, or thinners, as they may
damage the surface finishes.
• To avoid electrical shock and to preserve the product warranty, DO NOT disassemble
the camera. Refer servicing to qualified personnel only.
PACKAGE CONTENTS
Ensure that the items received match those listed on the order form and the packing slip.
In addition to this manual and a fully assembled camera, the dome camera packing box
includes:
A. Plastic Anchor x3
B. Round Head Screw
(Tapping Type) x3
C. Waterproof tape x1
D. Security Torx bit
E. Service Monitor BNC cable x1
F. Surface Mount template x1
1. Cable exit plug. Use a coin or a flat screwdriver to turn counter-clockwise to
remove.
2. Camera cable. When surface mounting, route through the cable exit opening.
3. Camera module/lens.
4. Dome bubble.
5. BNC video connector. Connect to an encoder, DVR/HVR or service monitor.
Four (4) video formats supported: HD-TVI (default), HD-AHD, HD-CVI and CVBS.
Use the video format switch (#2) to set video format as required.
6. Power connector (DC12V/AC24V).
7. Video format switch. Default video format setting: HD-TVI.
DISASSEMBLY AND INSTALLATION
To prepare the camera for mounting, remove the camera’s dome bubble by unscrewing
three screws using the Security torx bit provided. Do not remove the screws completely.
The dome bubble is secured to the camera body with the anti-drop wire.
Lift the dome bubble off.
Prepare the mounting surface:
• Depending on the type of
installation, additional mounting
accessories may need to be
purchased.
• It is the installer’s responsibility
to ensure that the mounting
surface is suitable for the
chosen installation method.
• Based on installation location
and surface type, supplied
screws and anchors may not be adequate. Mounting hardware is site-specific and
may need to be supplied by the installer.
Compatible i3 Mounting Accessories:
B5 - Pendant mount back box / bracket. 1” Male. Combine with DB61 for Wall mount
installations
DB61 - Wall Mount bracket. 1” Female. Combine with B5 for Wall Mount installations.
DIMENSIONS AND DEFINITIONS
1080P (2MP) Outdoor IR HD Analog Dome w/ Motorized Lens
Am53
HD
3
4
5
6
7
A
B
F
Waterproof tape
e Waterproof tape
pe Waterproof ta
f tape Waterproo
oof tape Waterpr
proof tape Water
C
D
111mm (4.4”)
Ø146mm (5.7”)
Ø99.94mm (3.93”)
Ø130mm (5.11”)
3x Ø4.6mm
(0.18”)
HIGH DEFINITION ANALOG VIDEO SUPPORT
Your Am53 camera supports the standard CVBS composite analog video stream (720x480)
and a high-definition (2MP) video stream in HD-TVI, HD-AHD, and HD-CVI format.
Note: Am53 camera supports a single video output at-a-time. No separate spot monitor
output is offered.
IMPORTANT: In order to use high-definition video, your Am53 camera must be
connected to a video encoder or standalone DVR/HVR that supports HD-TVI,
HD-AHD, or HD-CVI format.
Note: i3’s line of encoders and embedded standalone DVRs supports HD-TVI and CVBS
formats only.
CHANGING VIDEO FORMAT:
- Unscrew protection cap from the video format switch (#7 under Dimensions
and Definitions section).
- Press and hold the button for 5 seconds to change the video output format to
the next one in sequence.
Video format sequence: TVI (default) > AHD > CVI > CVBS.
1
2
E
USER MANUAL
Page -2-
Am53 Analog Dome Camera
LENS ADJUSTMENT
Your Am53 camera is equipped with the motorized 2.7-13.5mm lens. To achieve
desired view, start by adjusting the lens angle along the 3 axis by panning/tilting the
camera body and rotating the lens assembly. The lens zoom and focus can be adjusted
through i3’s encoder, i3’s standalone HVR’s local or remote interfaces, through SRX-Pro
v6/VPC interface, or through HD service monitor with BNC input.
ADJUST ZOOM/FOCUS via HR16
1. Connect Am53 to HR16.
2. In Internet Explorer, enter HR16 address. (Default: 192.0.0.16).
3. Enter user credentials in the Annexxus login screen.
(Default: i3admin/i3admin).
4. Go to SETUP > Camera > PTZ Settings
5. In Channel No., select the HR16 port where Am53 is connected (E.g.
Analog Camera 1).
6. In PTZ Protocol, select i3-HDA. Click Save.
7. Click LIVE to go back to the live mode. Select a single camera
division.
8. Use Previous/Next buttons to locate desired
Am53 camera.
9. Use the PTZ Control panel to adjust Zoom and
Focus until the desired view is achieved.
ADJUST ZOOM/FOCUS via SRX-PRO
SERVER v6 and lower
1. Repeat Steps 1-6 of the
ADJUST ZOOM/FOCUS via HR16
section.
2. Add HR16 to SRX-Pro Server’s IP camera tab.
3. In IP Camera tab, expand HR16 item to see all inputs. Assign Am53 input to SRX-
Pro Server video channel in Ch. In. drop-down menu.
SURFACE MOUNTING
1. Attach the supplied surface mounting template to the mounting surface.
2. Drill three mounting holes in the surface and insert supplied anchors.
3. Drill the conduit hole for the camera cable, as marked on the template (if applicable).
If routing the cable through the side cable exit, do not drill the cable exit hole, instead
remove the cable exit plug. If mounting on a wall, make sure the opening is pointing
down, to create a drip loop.
4. Use the tapping screws provided (if suitable for the installation) to secure the camera
to the prepared mounting surface.
5. Feed the camera cables through the conduit hole.
6. Connect camera’s BNC connector to the coaxial cable.
7. Connect camera to DC12V/AC24V power, 9.7W required.
8. Adjust the lens angle by panning and tilting the camera lens assembly and rotating
the camera lens base. Do not over-rotate beyond the stop point to avoid damage to
the camera.
9. Adjust the camera’s zoom and focus through a DVR/HVR, encoder, SRX-Pro/VPC
software or HD service monitor with BNC input.
See LENS ADJUSTMENT section for more information.
10. Adjust any additional camera settings (e.g. image brightness, color or contrast, day/
night mode, etc.).
See CAMERA MENU section for more information on camera’s
on-screen menu.
11. Once the desired view is achieved, re-attach the camera’s dome bubble onto the
camera module using the security torx bit provided.
4. Go to Hardware > Channels setup tab.
5. Locate the Channel that Am53 was assigned to in the Step
3 and set PTZ Camera Type to i3 GiPi.
6. Click the Live Mode button.
7. Go to View > Tree View and expand Advanced Control
panel.
8. Double-click on the Am53 camera to bring it into full
single-channel division.
9. Use the Advanced Control panel to adjust Zoom and
Focus until the desired view is achieved.
3-axis Range Limitations:
Pan:
0-355°
Tilt:
0-75°
Rotation:
0-355°
PENDANT MOUNTING
(Optional B5 back box required)
1. Attach B5 back box to the 1” pendant mounted pipe or pipe bracket.
To attach to 3/4” pipe, use a 1” to 3/4” reducer (not provided).
2. Follow DISASSEMBLY instructions to lift off camera’s dome bubble.
3. Complete Steps #6-7 in the
SURFACE MOUNTING
section.
4. Feed the camera cables into the B5 back box through the cable opening.
5. Use three machine type screws provided with B5 to secure the Am53 camera to the
B5 backbox through the three mounting holes on the camera body.
6. Complete Steps #8-11 in the
SURFACE MOUNTING
section.
WALL MOUNTING
(Optional DB61 gooseneck bracket and B5 back box required)
1. Mount DB61 gooseneck bracket on the wall. Follow installation instructions provided
with DB61.
2. Attach B5 back box to the DB61 gooseneck bracket.
3. Complete Steps #2-6 in the PENDANT MOUNTING section.
ADDING HR16 to SRX-PRO SERVER v7 and up
SRX-Pro v7 users must complete this step before adjusting lens
zoom/focus through VPC v7 and above.
1. Repeat Steps 1-6 of the
ADJUST ZOOM/FOCUS via HR16
section.
2. Log into Pro Setup
3. Add HR16
i. Click Add.
ii. Select HR16 in the list.
iii. Click ADD.
iv. Click List and enable PTZ toggle for all Am53 inputs on HR16.
i
ii
iii
iv
Product specificaties
| Merk: | I3International |
| Categorie: | Bewakingscamera |
| Model: | Am53 |
Heb je hulp nodig?
Als je hulp nodig hebt met I3International Am53 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Bewakingscamera I3International
13 Maart 2024
13 Maart 2024
13 Maart 2024
13 Maart 2024
13 Maart 2024
13 Maart 2024
13 Maart 2024
13 Maart 2024
13 Maart 2024
13 Maart 2024
Handleiding Bewakingscamera
- Brinno
- Blink
- HuddleCamHD
- Dahua Technology
- Conceptronic
- Kodak
- Zavio
- Planet
- BirdDog
- CRUX
- Atlantis Land
- Night Owl
- Qoltec
- Ezviz
- Aida
Nieuwste handleidingen voor Bewakingscamera
15 September 2025
2 September 2025
2 September 2025
2 September 2025
2 September 2025
1 September 2025
1 September 2025
1 September 2025
1 September 2025
1 September 2025