HQ EL-PIR70 Handleiding

HQ Bewegingsdetector EL-PIR70

Bekijk gratis de handleiding van HQ EL-PIR70 (66 pagina’s), behorend tot de categorie Bewegingsdetector. Deze gids werd als nuttig beoordeeld door 49 mensen en kreeg gemiddeld 4.5 sterren uit 25 reviews. Heb je een vraag over HQ EL-PIR70 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Download PDF

Pagina 1/66

EL-PIR70

Radar motion sensor

This sensor is an active motion detector. The integrated HF sensor emits high-

frequency electro-magnetic wave (5.8GHz) and receives their echo. The sensor

detects the change in echo from even the slightest movement in the light’s detection

zone. A microprocessor then triggers the “switch light ON” command. Detection is

possible through doors, panes of glass or thin walls.

Detection zones for ceiling mounting

1) Minimum reach 1m dia.

2) Maximum reach 8m dia.

Detection zones for wall mounting

3) Minimum reach 1m dia.

4) Maximum reach 8m dia.

Important: persons or objects moving towards

the light are detected best!

Installation procedures

1. Take down the top cover by turning it anti-clockwise (see g.1), and then tighten off

the two screws xing middle cover (see g. 2);

2. Hold base against the wall and mark drill holes, paying attention to any existing

wiring in the wall;

3. Drill the holes, insert wall plugs (6mm dia);

4. Put the power wire and load wire through the base holes;

5. Screw the base into place (see g. 3);

6. Connect the mains power supply and the load wire to the connection terminal

according to connection-wire mark.

7. Close the middle cover (see g. 3) and adjust knob to setting;

8. Fit glass shade and turn it clockwise (see g. 3).

g 1 g 2 g 3

Technical specications

power supply: 220-240VAC

power frequency: 50/60Hz

Installation sit: indoors, wall/ceiling mounting

HF system: 5.8GHz CW radar, ISM band

transmission power: <10mW

rated load:1200W: 220-240VAC

detection angle: 360°, 160°

reach:1-8m (dia.), adjustable

time setting: 5sec to 15min

light control: 2~2000LUX

Connection illumination

connect N,L with power; connect N, L’ with load

Reach setting (sensitivity)

Reach is the term used to describe the diameter of

the more or less circular detection zone produced

on the ground after mounting the sensor at a height

of 2.5m, turn the reach control fully anticlockwise

to select minimum reach (approx.1 m dia), and fully

clockwise to select maximum reach (approx. 8m dia).

Time setting

The light can be set to stay ON for any period of time between approx. 5sec

(turn fully anticlockwise) and a maximum of 15min (turn fully clockwise).

Any movement detected before this time elapse will re-start the timer. It is

recommended to select the shortest time for adjusting the detection zone

and for performing the walk test.

NOTE: after the light switches OFF, it takes approx. 1sec before it is able to start

detecting movement again. The light will only switch on in response to movement

once this period has elapsed.

Light-control setting

The chosen light response threshold can be innitely from approx. 2-

2000lux. Turn it fully anti-clockwise to select dusk- to-dawn operation at

about 2 lux. Turn it fully clockwise to select daylight operation at about

2000lux. The knob must be turned fully clockwise when adjusting the

detection zone and performing the walk test in daylight.

1-8 dia

5sec~15min

2~2000LUX

Product specificaties

Merk:	HQ
Categorie:	Bewegingsdetector
Model:	EL-PIR70
Kleur van het product:	Wit
Gewicht verpakking:	188 g
Montagewijze:	Plafond
Afmetingen verpakking (BxDxH):	105 x 105 x 55 mm
Type beeldsensor:	Passieve infraroodsensor (PIR)
Ingangsspanning:	220 - 240 V
Maximumbereik:	8 m
Afmetingen (B x D x H):	100 x 100 x 45 mm
Bedrijfstemperatuur (T-T):	0 - 40 °C