GT 800-1 Handleiding
GT
Auto alarm
800-1
Lees hieronder de đź“– handleiding in het Nederlandse voor GT 800-1 (16 pagina's) in de categorie Auto alarm. Deze handleiding was nuttig voor 37 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/16
GT 800/1/2/3
USER AND INSTALLATION MANUAL
1
SUMMARY
2
1.0 - INSTALLATION AND CONNECTIONS Page. 3
2.0 - GENERAL CONNECTION DIAGRAM Page. 5
3.0 - DESCRIPTION OF THE PROGRAMMABLE FUNCTIONS Page. 6
3.1 - Self-coding vehicle indicators impulses number Page. 6
3.2 - Switches/Discriminators signals stabilizer Page. 6
3.3 - Memorization of switches/discriminators signals only after actuator signals Page. 6
3.4 - Memorisation of actuator signals of changeable type Page. 6
3.5 - Anti-hijack door signal stabilizer Page. 6
3.6 - Acoustic signal when arming/disarming the alarm system Page. 6
3.7 - Visual signal when arming/disarming the alarm system Page. 6
3.8 - Courtesy light switching on when disarming Page. 6
4.0 - SET FUNCTIONS Page. 6
5.0 - DESCRIPTION OF THE ALARM SYSTEM ARMING/DISARMING COMMAND WIRES Page. 8
6.0 - DOORS LOCK/UNLOCK SIGNALS SELF-CODING Page. 8
7.0 - RAPID TEST Page. 9
8.0 - SELF-POWER SUPPLY Page. 10
9.0 - FINAL OPERATIONS Page. 10
10.0 - USER MANUAL Page. 11
10.1 - Alarm system arming/disarming Page. 11
10.2 - Electric windows closing command function Page. 11
10.3 - Protections Page. 11
10.4 - If the alarm sounds ... Page. 11
10.5 - Check status LED Page. 11
10.6 - Emergency disarming with “GT CARD CODE” Page. 12
10.7 - How to isolate additional sensors and ultrasonic sensor
when arming the alarm system Page. 12
10.8 - Anti-hijack function Page. 12
10.9 - Visual signal function when arming/disarming the alarm system Page. 13
10.10 - Acoustic signal function when arming/disarming the alarm system Page. 13
10.11 - Functions check Page. 13
11.0 - COMPLIANCE DECLARATION Page. 13
12.0 - WARRANTY CONDITIONS Page. 14
13.0 - TECHNICAL FEATURES Page. 15
3
1.0 - INSTALLATION AND CONNECTIONS
WARNINGS:
- Place the GT800 alarm in the engine compartment, away from direct sources of water
spray and high tension wiring.
- Solder and isolate all connections.
- Isolate the wires not connected.
- The alarm system should be mounted by a professional installer.
1 - Connect the BROWN wire to O/E vehicle earth.
2 - Connect the RED wire to a permanent 12 volts supply (use the supplied 15 Amp fuse).
3 - Connect the PINK wire of the alarm (max. capacity 80 mA) to the PINK wire of any additional
sensors/modules (i.e. microwave sensor, electric window module).
4 - Connect the GREEN/BLACK wire of the alarm to the GREEN/BLACK wire of any additional
sensors.
5 - Connect the YELLOW wire to an ignition switched live (+15/54) that remains live even
when the engine is being cranked. Do not connect to the same wire used for the engine
immobilisation.
6 - Connect the ORANGE wires to the left and right hand vehicle indicators.
7 - Connect the GREEN wire to the boot and bonnet pin switches, provided that they are
switched earth only.
8 - Connect the GREEN/BROWN wire to the existing doors pin switches, provided that they
are switched earth only.
9 - If you want to activate the ANTI-HIJACK FUNCTION connect the GREEN/BLUE wire to
the original driver’s door pin switch, provided that it is a switched earth only.
10 - Connect the BLUE/VIOLET wire to the “comfort” command of the vehicles equipped with
negative “comfort” closing function (the signal duration is of about 40 seconds).
11- The WHITE and GREY wires are used for the engine immobilisation on either diesel or
petrol vehicles. Cut the ignition switched live that feeds, depending on the type of vehicle, the
fuel pump relay, or the solenoid valve (diesel vehicles). Connect one end to the GREY wire
and the other to the WHITE wire.
WARNING:
- On the vehicles equipped with an ignition key transponder immobiliser, it is not
necessary to connect the WHITE and GREY wire of the alarm, therefore these two
wires can be isolated.
12 - The YELLOW/BLACK wire sends a negative intermittent signal when triggered alarm
(max 100mA). It can be used to command the vehicle’s horn relay.
13 - Place the LED/BUTTON on the dashboard (in a visible way) and connect it to the
connectors in the alarm wiring loom.
Product specificaties
| Merk: | GT |
| Categorie: | Auto alarm |
| Model: | 800-1 |
Heb je hulp nodig?
Als je hulp nodig hebt met GT 800-1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Auto alarm GT
25 April 2023
25 April 2023
25 April 2023
25 April 2023
25 April 2023
25 April 2023
25 April 2023
25 April 2023
25 April 2023
25 April 2023
Handleiding Auto alarm
- Auto alarm HP
- Auto alarm Audiovox
- Auto alarm Eufab
- Auto alarm Gemini
- Auto alarm Spy
- Auto alarm Technaxx
- Auto alarm Viper
- Auto alarm Waeco
- Auto alarm Jablotron
- Auto alarm Olympia
- Auto alarm Cobra
- Auto alarm Clifford
Nieuwste handleidingen voor Auto alarm
7 Februari 2024
7 Februari 2024
7 Februari 2024
6 September 2023
30 December 2022
15 Januari 2023
20 Maart 2023
10 Juli 2023
10 Juli 2023
10 Juli 2023