GE ZDIS150ZSS Handleiding

GE Ijsmachine ZDIS150ZSS

Lees hieronder de 📖 handleiding in het Nederlandse voor GE ZDIS150ZSS (18 pagina's) in de categorie Ijsmachine. Deze handleiding was nuttig voor 27 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/18
Installation
Instructions
Automatic Ice maker
ZDIC150
ZDIS150
Design Guide
With Installation Instructions
monogram.com
Installation Instructions
 BEFORE YOU BEGIN:
Read these instructions completely and carefully.
 IMPORTANT:
Save these instructions for local inspector’s use.
 IMPORTANT:
Observe all governing codes and ordinances.
Note to Installer – Be sure to leave these
instructions with the Consumer.
Note to Consumer – Keep these instructions with
your Owner’s Manual for future reference.
WARNING:
This appliance must be properly grounded.
Failure to do so can result in death, fire or electrical
shock. See “Power Supply,” page 6.
AVERTISSEMENT :
Cet appareil doit être correctement mis à la terre.
Le non-respect de ces instructions peut causer la
mort, un incendie ou un choc électrique. Consulter «
Alimentation électrique », page 6.
If you received a damaged ice maker, you should
immediately contact your dealer or builder.
Proper installation is the responsibility of the
installer. Product failure due to improper installation
is not covered under the GE Appliance Warranty.
See the Owner’s Manual for warranty information.
8VHWKLVDSSOLDQFHRQO\IRULWVLQWHQGHGSXUSRVH
Check with local utilities for electrical codes that
apply in your area. Local codes vary. Installation,
electrical connections and grounding must comply
with applicable codes. In the absence of local codes,
the ice maker should be installed in accordance
with National Electrical Code ANSI/NFPA 70-1990 or
latest edition.
For Monogram local service in your area, call
1.800.444.1845.
For Monogram Service in Canada, call
1.800.561.3344.
For Monogram Parts and Accessories, call
1.800.626.2002.
2
CONTENTS
Design Information
Models Available .................................................................... 3
Optional Accessories ........................................................... 3
Tools and Materials Required ........................................ 3
Cutout & Product Dimensions .........................................4
Installation
Advance Planning .................................................................4
Water Supply ........................................................................... 5
Power Supply ...........................................................................6
Remove Packaging ............................................................... 6
Water Filtration System .................................................6, 7
Adjust Height of Ice maker ...............................................7
Connect the Drain .................................................................9
Connect Water Supply to Appliance ............................9
Reverse Door Swing ...................................................10, 11
Accessories
ZPK2 Auxiliary Pump Kit ............................................12-15
ZIP75BB Kit for 3/4” thick panels ..........................16, 17
Design Information
MODELS AVAILABLE
ZDIC150ZBB, ZDIS150ZSS
Available in black and stainless steel.
The ice maker may be installed below a countertop
or used free-standing.
3
OPTIONAL ACCESSORIES
=,3%%³For the installation of a trimless
3/4” thick custom panel on black models (not for
stainless steel models). This kit provides a handle
that can be installed with the custom panel.
A custom handle of your choice may be installed onto
the 3/4” panel. See installation instructions
on pages 10 and 11.
ZPK2 Drain Pump Kit - For use when a floor drain is
not available. The drain pump must be installed
inside the unit and can pump discharge water at a
maximum vertical height of 10 feet. 10 feet of tubing
is supplied with the kit.
TOOLS AND MATERIALS REQUIRED FOR BASIC INSTALLATION
µVRFNHW
µDGMXVWDEOHZUHQFK
/HYHO
*(6PDUW&RQQHFW™ Refrigerator Tubing Kit or 1/4” O.D.
copper tubing, of sufficient length to reach the installation
)ODWEODGHVFUHZGULYHU
µDQGµRSHQHQGZUHQFKHVRUDGMXVWDEOHZUHQFKHV
µQXWGULYHU

Product specificaties

Merk: GE
Categorie: Ijsmachine
Model: ZDIS150ZSS

Heb je hulp nodig?

Als je hulp nodig hebt met GE ZDIS150ZSS stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Ijsmachine GE

GE

GE Profile PIP70SS Handleiding

6 December 2023
GE

GE ZDI15CBB Handleiding

13 Juni 2023
GE

GE Profile Opal OPAL01NSS Handleiding

11 Mei 2023
GE

GE Profile OPAL01PSS Handleiding

4 Mei 2023
GE

GE ZDIS15CSS Handleiding

30 April 2023
GE

GE UCC15NJII Handleiding

22 April 2023
GE

GE Profile OPAL01NKT Handleiding

12 April 2023
GE

GE UNC15NPRII Handleiding

10 April 2023
GE

GE ZDIC150WBB Handleiding

2 April 2023
GE

GE Profile OPAL01PKT Handleiding

21 Maart 2023

Handleiding Ijsmachine

Nieuwste handleidingen voor Ijsmachine

Lagrange

Lagrange Sorbetière 409 Handleiding

25 April 2024
Musso

Musso 406006 Handleiding

20 April 2024
Musso

Musso 406003 Handleiding

20 April 2024
Musso

Musso 406010 Handleiding

20 April 2024
Musso

Musso 406001 Handleiding

20 April 2024
Dash

Dash DPIC100 Handleiding

10 April 2024
Carpigiani

Carpigiani Pastochef RTX Handleiding

6 April 2024
Carpigiani

Carpigiani Miniwip Handleiding

6 April 2024
Carpigiani

Carpigiani AES 381 Handleiding

6 April 2024
Carpigiani

Carpigiani 603 GM Handleiding

6 April 2024