Futaba R3006SB Handleiding

Futaba Radiografisch bestuurbaar speelgoed R3006SB

Lees hieronder de 📖 handleiding in het Nederlandse voor Futaba R3006SB (5 pagina's) in de categorie Radiografisch bestuurbaar speelgoed. Deze handleiding was nuttig voor 38 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/5

Applicable systems: Futaba T-FHSS Air-2.4GHz system transmitter

R3006SB T-FHSS Air-2.4GHz Bidirectional Communication System

S.BUS2 / S.BUS Port and 6 Channels for Conventional System Receiver

Compliance Information Statement

(for U.S.A.)

This device, trade name Futaba Corporation, model number R3006SB, complies with

part15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may

cause undesired operation.

CAUTION:

To assure continued FCC compliance:

$Q\FKDQJHVRUPRGL¿FDWLRQVQRWH[SUHVVO\DSSURYHGE\WKHJUDQWHHRIWKLVGHYLFHFRXOG

void the user's authority to operate the equipment.

 7KLV HTXLSPHQW FRPSOLHV ZLWK )&& UDGLDWLRQ H[SRVXUH OLPLWV VHW IRUWK IRU DQ

uncontrolled environment.

7RPHHWWKH5)H[SRVXUHUHTXLUHPHQWVRIWKH)&&WKLVGHYLFHVKDOOQRWEHFRORFDWHGZLWK

another transmitting device.

The responsible party of this device compliance is:

Futaba Service Center

3002 N Apollo Drive Suite 1, Champaign, IL 61622 U.S.A.

7(/RU(PDLOIXWDEDVHUYLFH#KREELFRFRP6XSSRUW

5 % ÀS Speci cations

T-FHSS Air-2.4GHz system/S.BUS2 and S.BUS port and 6 channels for

conventional system receiver

• Dual antenna diversity

• Size: 1.7 x 0.98 x 0.35 in. (43.1 x 25.0 x 8.8 mm)

• Weight: 0.3 oz. (8.5g)

• Power requirement: 4.6V to 7.4V

• Battery F/S Voltage: It sets up with a transmitter

* Be sure that the battery is the correct size for the amount and type of servos

being used. When using a BEC, be sure that it is capable of delivering constant

voltage and can accept enough current that will be used by the RX and servos.

Do not use a dry cell battery with this system.

Thank you for purchasing a Futaba R3006SB T-FHSS Air-2.4GHz compatible receiver. The R3006SBUHFHLYHUIHDWXUHVELGLUHFWLRQDOFRPPXQLFDWLRQ

with a T-FHSS Air-2.4GHz Futaba transmitter using the S.BUS2 S.BUS2 port. Using the port an impressive array of telemetry sensors may be utilized.

It also includes both standard PWM output ports and S.BUS output ports.

LED Indication

Green Red Status

Off Solid No signal reception

Solid Off Receiving signals

Alternate blink Unrecoverable error (EEPROM, etc.)

(Antenna installation)

90˚

Please refer the table below

for LED status vs receiver's

condition.

1M23N17485

6%86

SRUW

6%86SRUW

6%ك

6%%ك

6%866HUYR

6%86*\UR

0RGHVZLWFK

$QWHQQD

/('

6HUYRIRU FRQYHQWLRQDO

V\VWHP

&KDQQHORXWSXW

&KDQQHORXWSXW

%DWWHU\WR6%%

56% 7HOHPHWU\6HQVRU

6%86+8%

7HOHPHWU\6HQVRU

,WVQHFHVVDU\WRFKDQJHLWWR

0RGH%6%86

Usage precaution

• Futaba T-FHSS Air system does not work with current Futaba T-

FHSS / S-FHSS / FHSS / FASST / FASSTest system.

• The R3006SB receiver can only be used with T-FHSS Air capable

transmitters.

WARNING

Changes or modification not expressly approved by the party

responsible for compliance could void the user’s authority to operate the

equipment.

The R3006SB receiver should be protected from vibration by foam

rubber, Velcro or similar mounting methods. Protect from moisture.

Keep away from conductive materials to avoid short circuits.

Antenna installation precaution

Don't cut or bundle the receiver antenna wire.

Don't bend the coaxial cable. It causes damage.

The antennas must be mounted in such a way to assure they are

strain relieved.

Keep the antenna as far away from the motor, ESC and other noise

sources as you possibly can.

Be sure that the two antennas are placed at 90 degrees to each other.

• The R3006SB has two antennas. In order to maximize signal reception

and promote safe modeling Futaba has adopted a diversity antenna

system. This allows the receiver to obtain RF signals on both antennas

and ﬂy problem-free.

Antenna installation for carbon fuselage

WARNING

You must leave 30mm at the tip of the antenna fully exposed. The ex-

posed antenna should be secured so that it cannot move around or back

inside of your aircraft.

S.BUS2 precaution

DANGER

Don't connect a connector, as shown right.

• It will be a short-circuit, if it connected in

this way. A short circuit across the battery

terminals may cause abnormal heat, fire

and burning.

Don't connect servo for conventional system to S.BUS/S.BUS2 port.

• Digital servo for conventional system→ It does not operate.

• Analog servo → It may cause abnormal heat, ﬁre and burning.

WARNING

Only S.BUS2 capable devices may be connected the S.BUS2 port.

Standard S.BUS servos and gyros should not be connected the S.BUS2

port.

(Typical installation)

5HFHLYHU

DANGER

Do not insert either a switch

or battery in this manner.

本產品符合低功率電波輻射性電機管理辦法

第十二條、第十四條等條文

規定

1. 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均

不得擅自變更頻率、加大功率或變更原設計之特性及功能。

2. 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干

擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通

信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通

信或工業 ,科學及醫療用電波輻射性電機設備之干擾。

WARNING

Do not perform the linking procedure while the motor's main wire con-

nected or the engine is operating as it may result in serious injury.

When the linking is complete, please cycle the receiver power and en-

sure the receiver is properly linked to the transmitter.

Please power up your system in this order. Transmitter ﬁrst, followed

by the receiver.

FUTABA CORPORATION

<DEXWVXND&KRVHLPXUD&KRVHLJXQ&KLEDNHQ-DSDQ

3KRQH)DFVLPLOH

Link to the transmitter

(DV\/LQN ,' DOORZV 7)+66$LU UHFHLYHUVWR OLQNWR FRPSDWLEOH

transmitter without pressing the link button on the receiver.

1 Bring the transmitter and the receiver close to each other,

within 20 inches (half meter).

2 Turn on the transmitter. Place the transmitter into the receiver

linking mode.

3 Turn on the receiver.

4 The receiver will wait for the linking process to begin for 3

seconds. Following that it will return to the normal operation

mode.

5 When the LED of the receiver changes from blinking red to

solid green, linking is completed.

(A link waiting state is ended in 3 second.)

• Refer to the transmitters operation manual for complete details on how to place the

transmitter into the linking mode.

• If there are many T-FHSS Air systems turned on in close proximity, your receiver

might have difﬁculty establishing a link to your transmitter. This is a rare occurrence.

However, should another T-FHSS Air transmitter/receiver be linking at the same

time, your receiver could link to the wrong transmitter. This is very dangerous if you

do not notice this situation. In order to avoid the problem,we strongly recommend

you to double check whether your receiver is really under control by your

transmitter.

• If the System Type of the transmitter is changed, the receiver will need to be re-

linked to the transmitter.

Channel Modes (S.BUS ⇔6CH )

The R3006SB is capable of changing its channel allocations as described

in the table below.

1 Turn on the receiver. (At this moment, the transmitter should

be off.) Then, blinks RED in about 3 seconds. Next, wait LED

until it becomes solid RED.

2 Press and hold the more than 5 seconds.Mode switch

3 Release the button when the blinks RED and GREEN LED

simultaneously.

4 The receiver is now in the "Operation CH Set" mode. At this

moment, the LED indicates current set status through ﬂashing

a pattern that corresponds to the CH mode.

&DQQRWH[LWWKLV&+VHWWLQJPRGHEHIRUHWKHRSHUDWLRQPRGHLV¿[HG

6HHWKHEHORZWDEOHWKDWVKRZVFRUUHVSRQGHQFHEHWZHHQ&+PRGHDQGZD\

RIÀDVKLQJ/('

'HIDXOW&+PRGHLV0RGH&+

5 By pressing the Mode switch, the operation CH is switched

sequentially as " Mode A" "Mode B" "Mode A"....

6 The operation mode will be set by pressing the Mode switch

more than 2 seconds at the desired CH mode.

7 Release the button when the blinks RED and GREEN LED

simultaneously. Then, the operation CH is ﬁxed.

6 After conﬁrming the operation CH mode is changed, turn off

and back on the receiver power.

7KH ³2SHUDWLRQ &+6HW´ PRGH FDQQRW EHFKDQJHG GXULQJ WKHUHFHLYHU

communicates to the transmitter.

T-FHSS Air

T-FHSS Air is a bidirectional communication system between the

56% UHFHLYHU DQG7)+66$LUFDSDEOH WUDQVPLWWHUV  0XOWLSOH

optional telemetry sensors may be connected to the S.BUS2 on the

receiver and that data is in turn displayed on the transmitter.

*Please see your transmitters operation manual to conﬁgure transmitter to

operate with telemetry sensors.

S.BUS2

S.BUS2 H[WHQGV S.BUS and supports bidirectional communication.

Sensors are connected the S.BUS2 port.

*Only S.BUS2 capable devices may be connected the S.BUS2 port.

Standard S.BUS servos and gyros should not be connected the S.BUS2

port.

If the R3006SB receiver was previously linked to another transmitter,

make sure that transmitter is not operating while linking the receiver to

the new transmitter.

Mode A Mode B

6/SB 6CH S.BUS

Red LED blink 1 time 2 time

56%&+0RGHWDEOH

WARNING

Turn on the power in transmitter receiver order. In addition, always check the operation of all the servos before ﬂight. →

Do not insert or remove the servo connector while the receiver power is ON.

Since the S.BUS servo switches the operation mode automatically according to the type of signal (S.BUS signal/PWM signal) from the receiver, if the connector is inserted

or removed while the power is ON, an S.BUS connected servo will be erroneously recognized and may stop.

©FUTABA CORPORATION 2015, 05 (1)

What is S.BUS?

Unlike conventional radio control systems, the S.BUS system uses data

communication to transmit control signals from a receiver to a servo,

gyro, or other S.BUS compatible device. This data includes commands

such as “move the channel 3 servo to 15 degrees, move the channel 5

VHUYRWR GHJUHHV´WR PXOWLSOHGHYLFHV7KH  GHYLFHVH[HFXWHS.BUS

only those commands for their own set channel. For this reason, it can

be used by connecting multiple servos to the same signal line. S.BUS hub S.BUS hub

S.BUS output

S.BUS

Ch output/

Battery terminal

R3008SB

Battery S.BUS servo

Conventional

servo

2ch 4ch

3ch 5ch

6ch

[Connection by S.BUS system]

* Set the channel of S.BUS servos by using an SBC-1 channel changer, CIU-2 USB

serial interface or the programming software resident in the T6K transmitter.

* Can also be used together with conventional servos. However, conventional ser-

vos cannot be used by the S.BUS output.

* When using servos with a remote battery pack, use S.BUS Hub with Cable (2-

way/remote battery pack use).

Please refer to the instruction manual of S.BUS Hub with Cable (2-way/remote

battery pack use) for the connection method.

'HIDXOW&+PRGH

Product specificaties

Merk:	Futaba
Categorie:	Radiografisch bestuurbaar speelgoed
Model:	R3006SB
Kleur van het product:	Zwart
Internet radio:	Nee
Ondersteunde frequentiebanden:	SW
Aantal kanalen:	6 kanalen