Futaba R204GF-E Handleiding

Bekijk gratis de handleiding van Futaba R204GF-E (2 pagina’s), behorend tot de categorie Radiografisch bestuurbaar speelgoed. Deze gids werd als nuttig beoordeeld door 23 mensen en kreeg gemiddeld 4.2 sterren uit 6 reviews. Heb je een vraag over Futaba R204GF-E of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Compliance Information Statement

(for U.S.A.)

This device, trade name Futaba Corporation of America, model number R204GF-E, complies with part15 of the FCC

Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesiredoperation.

The responsible party of this device compliance is:

Futaba Service Center

3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.

TEL (217)398-8970 or E-mail: support@futaba-rc.com (Support)

FUTABA CORPORATION

1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan

Phone: +81 475 32 6982, Facsimile: +81 475 32 6983

©FUTABA CORPORATION 2011, 11 (1)

R204GF-E Specifications:

(S-FHSS/FHSS system, 4-channel receiver)

s2ECEIVINGON'(ZBAND

s3YSTEMS-FHSS/FHSSSYSTEMAUTODETECTION

At S-FHSS

.ORMAL(IGHSPEEDMODEAUTODETECTION

s2ECEIVING2ANGEMFTATTHEBESTCONDITIONS

s

/PERATINGVOLTAGE4YP66

SHAREDWITHSERVO

s &3AND"ATTERY&3FUNCTION4HEOPERATIONCHANNELSDIFFERACCORDINGTOTHETRANSMITTERUSED(OWEVER"ATTERY

&3DOESNgTFUNCTIONWHENITISUSEDWITH&(33AND&3BECOMESONLY#(

s "ATTERY&3VOLTAGE6

s#URRENTDRAINM!ATNOSIGNAL

s3IZEXXvXXMM

s7EIGHTOZG

*The Battery F/S voltage is set for 4-cell NiCd/NiMH battery. Battery F/S function doesn't work

properly when other type battery is used.

󾛽WARNING

NEVERUSE DRY BATTERIESFORTHE

POWERSUPPLYOF THER204GF-Eas

THEYMAYCAUSEDIFlCULTIES

NEVER use the R204GF-EIN'0

CARS

Link Procedure

Each transmitter has an individually assigned,

unique ID code. In order to start operation, the

receiver must be linked with the ID code of the

transmitter with which it is being paired. Once the

link is made, the ID code is stored in the receiver

and no further linking is necessary unless the

receiver is to be used with another transmitter.

10LACETHETRANSMITTERANDTHERECEIVERCLOSE

TOEACHOTHERWITHINHALFMETER

24URNONTHETRANSMITTERANDTHERECEIVER

3 0USHAND HOLDTHE ,INK SWITCH ONTHE

RECEIVER

47HENTHELINKISCOMPLETETHE,%$ONTHE

RECEIVERCHANGESTOSOLIDGREEN

0LEASE REFERTO THE TABLE BELOW FOR ,%$ STATUS

ANDRECEIVERCONDITION

.OSIGNALRECEPTION ,%$/FF

2ECEIVINGSIGNALS ,%$/N

2ECEIVINGSIGNALSBUT)$

ISUNMATCHED ,%$"LINK

0OWER/NWHEN&3

SETSIT

,%$%ARLY

"LINKTHElRST

ONESECOND

)F THERE ARE MANY S-FHSS/FHSS SYSTEMS TURNED

ONAROUNDYOURRECEIVERITMIGHTNOTLINKTOYOUR

TRANSMITTER )N THISCASE EVEN IF THERECEIVERS

,%$ STAYS SOLID GREEN UNFORTUNATELYTHE

RECEIVERMIGHTHAVEESTABLISHEDALINKTOONEOF

THE OTHER TRANSMITTERS 4HISIS VERY DANGEROUS

IF YOUDONOT NOTICE THIS SITUATION  )N ORDER TO

AVOIDTHE PROBLEM WE STRONGLY RECOMMEND

YOU TO DOUBLECHECK WHETHERYOUR RECEIVER IS

CONTROLLED BY YOUR TRANSMITTER BY GIVING THROTTLE

INPUTETCANDTHENCHECKINGSERVORESPONSE

󾛽WARNING

!FTERTHE LINKINGIS DONEPLEASE CYCLE

RECEIVERPOWERANDCHECKIFTHERECEIVER

TOBELINKEDISREALLYUNDERTHECONTROLBYTHE

TRANSMITTERTOBELINKED

$ONOT PERFORMTHE LINKING PROCEDURE

WITHMOTORgS MAINWIRE CONNECTEDOR

WITHTHEENGINEOPERATINGASITMAYRESULTIN

SERIOUSINJURY

Link switchLED

Ch4 output/Battery terminal (B)

Ch output (1 to 3)

Operating Precautions:

Once the R204GF-E DETECTS THE

S-FHSSNORMALMODES-FHSSHIGH

SPEED MODE ORFHSS MODE THE

DETECTED MODE IS LOCKED AS LONG

AS THE POWER IS /. 7HEN NEED

TOCHANGETHE MODEPLEASE CYCLE

POWER

Note:The R204GF-E is compatible with the S-FHSS or FHSS

system transmitters .

*Futaba S-FHSS/FHSS system does not work with current Futaba FASST system.

Usage condition on "High Speed mode"

󾛽CAUTION

7HEN USING THEHIGHSPEED MODEUSEA &UTABA

DIGITAL SERVO INCLUDING BRUSHLESS SERVO !NALOG

SERVOSCANNOTBEUSED

s4HEUSEOFANALOGSERVOSMAYCAUSESERVOTROUBLE

1M23N17446

S-FHSS/FHSS-2.4GHz

system

(Auto Detection),

For EP Car models

Built-in antenna

4-channel receiver

Thank you for purchasing the R204GF-E receiver.

The R204GF-Eis designed for use with the Futaba

S-FHSSor FHSSsystem transmitter. The S-FHSS

system has two(2) operation mode as shown below.

s.ORMALMODE(IGH3PEEDMODE

The "Normal mode" accepts any type of servos or the

peripherals as the frame rate of the output is 13.6ms.

The "High Speed mode" only accepts the digital

servos, including BLS series, and most peripheral

equipments such as the brushless ESCs. The frame

rate of the outputs is 6.8ms. However, there is a

transmitter that cannot correspond, too.

Please pay special attention to the information

contained within this manual and transmitter's manual

LQRUGHUWRKDYHDSOHDVDQWUXQQLQJÀ\LQJH[SHULHQFH

s"UILTINANTENNA

The R204GF-E receiver is designed to be used only

for EP Car models. Due to the special design of the

R204GF-E, we cannot recommend its use in other

types of models (gas poweredmodels.)

s4HE 2'&%IS COMPATIBLE WITHTHE

S-FHSS or FHSS system transmitters.

R204GF-E

Product specificaties