Futaba FP5NLH Handleiding

Futaba Radiografisch bestuurbaar speelgoed FP5NLH

Lees hieronder de 📖 handleiding in het Nederlandse voor Futaba FP5NLH (6 pagina's) in de categorie Radiografisch bestuurbaar speelgoed. Deze handleiding was nuttig voor 30 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/6

Futaba

DIGITAL PROPORTIONAL

RADIO CONTROL

INSTRUCTION MANUAL

D60400

Thank you for Futaba purchasing a digital proportional

radio control set.

Please read using this manual carefully before your set.

FEATURES OF FP-5NLH

The FP-5NLH for FM helicopters is an proportional radio con-

trol

set

for helicopters

with

ergonomic

case

crested

result of of the exhaustive pursuit easier operation. Newly de-

signed sticks servo revers- for smooth positive and operation,

ing switches for (Ad- all channels, and aileron elevator AST

justable

Servo

Throw),

pitch

control

trim,

idle up,

and

other

innovations based on of the opinions many modelers. RC

TRANSMITTER FP-T5NLH

• Reliability substantially improved by using industrial robots to as-

semble the PC board.

• Servo reversing switch for each channel. Servos are reversed by using

this switch

• Aileron and elevator AST Throw). throw (Adjustable Servo Servo can

be set as desired.

• Easy-to-adjust two knob revolution mixing. type Throttle pitch con-

trol rudder mixing.

• Pitch the control trimmer. Approximately 30% of pitch control servo

throw can allows optimum be trimmed, this pitch control the of

model.

• Throttle hold and switch trimmer for auto rotation.

• This allows the Rotor r.p.m. to maintained at an effective control

speed, even when the pitch is reduced, allowing maneuvers which

were impossible in the past to be performed.

• Newly and designed open gimbal sticks operate smoothly reliably.

Spring tension mechanism allows adjustment of the operating feel of

the stick lever.

• Nonslip allows length adjustable lever head adjustment of the stick as

desired.

• Throttle ATL. Adjustable throttle limiter type throttle trim. As the

high

side

does

not

change

even

when

the

trim

altered,

very

convenient when connecting the linkage, etc.

• RF PC board module system.

• Functional case, created as a result of pursuit of the exhaustive easier

operation, has evolved which a case thick fits into the palm of the

hand.

• Square level meter the transmitter at indicates the supply power

voltage.

• Excellent radiation efficiency, strong 8-stage telescoping antenna.

• Neck strap bracket provided as the standard. Operation is easier if

transmitter is hung your neck using strap. from by the optional neck

• Built-in NiCad battery.

RECEIVER FP-R107N

• Compact, high receiver performance FM 7-channel with PC board

space reduced to a minimum.

•Special IF amp for radio improves communications the eﬀective

receiving range stability.

• Narrow band ceramic filter improves of rejection adjacent channel

interference.

• Futaba original squelch circuit reduces erroneous operation by weak

signals (when passing a dead point, etc.) and erroneous operation by

natural noise when no signals are being received.

• Large capacitor copes with voltage changes when a battery is used.

• Vibration-resistant pin connectors.

• Fiberglass epoxy PC board with thru-the-hole plating vibration is and

shock resistant.

SERVO FP-S130

SMALL, RUGGED, HIGH NEUTRAL SERVO

• Small, & double ball bearing, water-tight dusttight servo. output High

torque 55.6 oz-in (4kg-cm), high-speed 0.24sec/60°

• New indirect drive potentiometer improves vibration and shock resist-

ance and neutral accuracy.

• Futaba low-power custom 1C provides extremely high torque, narrow

dead band, and superior tracking.

• Fiberglass reinforced PBT (polybutylene terephthalate) injection

molded servo case and is mechanically strong invulnerable to glow

fuel.

• Strong polyacetal resin ultra-precision servo gear features smooth

operation, positive neutral, and very little backlash.

• Fiberglass reinforced epoxy resin PC board with thru-the-hole plating

improves servo amp vibration and shock resistance.

• Three pin connector eliminates faulty contact and improves reliability

against vibration and shock. has Housing a reverse insertion preven-

tion mechanism.

• Special grommet simplifies mounting of the has servo and an excel-

lent cushioning effect.

• Six splined special adjustable horns.

SET CONTENTS AND RATINGS

(Specifications are to change subject without prior notice.)

Transmitter

Receiver

Servo

NiCad battery

Switch

Others

PCM

FP-T5NLH x 1

FP-R107N x 1

FP-S130 x 4

NR-4J x 1

SSW-J

Charger, Ribbon, Mounting Spare horn. screw.

FP-5NLH

TRANSMITTER FP-T5NLH

2 stick, 5 channels w/servo reverse, aileron

and elevator AST, helicopter mechanism

72MHz band.53MHz band

FM (Frequency modulation)

9.6 volts NiCad battery (NT-8LP)

170mA (at 12V)

Operating system

Transmitting frequency

Modulation system

Power requirement

Current drain

RECEIVER FP-R107N

72MHz band .53MHz band

Receiving frequency

Intermediate frequency

Power requirement

Current drain

Dimensions

Weight

Receiving range

455kHz

4.8V, NiCad battery (common use servo) with

13.5mA (4.8V reception)

1.38 x x 20.3mm) 2.42 x x 0.8 in (35.2 61.7

1.55oz (43g)

550 yards (500m) on the ground, 1,100 yard

(1000m) in the air. [FP-T5NLH]

(at the best conditions)

SERVO FP-S130

+pulse width control

Control system

Operating angle

Power requirement

Current drain (IDLE)

Output torque

Operating speed

Dimensions

Weight

One side 45° more or (at idle)

4.8V (Shared with receiver)

5.0V,

8mA

55.6 oz.in (4kg-cm)

0.24sec/60°

1.52 x 34.5mm) 0.77 x 1.36 in (38.5 x 19.5 x

1.47oz (42g)

TRANSMITTER FP-T5NLH CONTROLS

Fig. 1 shows the name each of part of the transmitter.

Memorize the position and operation of each

switch and control.

Transmitter crystal

Idle up trimmer

Antenna

Pitch control knob trimming (CH5)

Throttle hold trimmer

Carrying bar

Throttle

hold switch

Revolution mixing down knob

Revolution mixing up knob

Idle up switch

Level meter

Throttle trim

lever

Rudder trim

lever

Throttle

Rudder

Servo reversing

switches

Power

switch

Neck strap bracket

Charging jack

Aileron trim lever

Throttle trim

lever s/ATL

Aileron

Elevator

Nonslip

adjustable lever head

MODE II

Battery cover

Fig.1

Transmitter

NiCad battery

NT-8LP

Aileron AST

trimmer

Elevator AST

trimmer

In the following descriptions, all the servo reversing switches

are assumed to normal When are be in the position. they in the

reverse position, operation is the opposite that of described.

Mixing circuit is used the torque reaction of for cancelling the main

rotor. The controls for set minimum the mixing necessary for heli-

copter flight.

Aileron Aileron operation

Elevator Elevator operation

Throttle Throttle operation

Rudder Rudder operation

Pitch control trimming knob (CH5)

Pitch control trimming knob. 30% Approximately of the full throw

of the servo can be adjusted and set. Normally, it is set for the best

pitch during flight.

Aileron trim trimmer. lever Aileron

Elevator trim lever Elevator trimmer.

Throttle trim lever w/ATL

Adjustable throttle limiter

type

trim

lever.

Operates

a trim lever only when the

throttle stick is at the

SLOW side as shown in

Fig.

SLOW

Servo throw by

throttle trimmer

As the HIGH side does not

change even when the trim

is altered, it is extremely

convenient when connect-

ing the linkage, etc.

(30% of full throw;

Throttle servo

Rudder trim lever Rudder trimmer.

Revolution mixing ratchet down side

knob

(down

side

knob)

Revolution mixing up side ratchet knob) knob (up side

• Knob which adjusts the throttle rudder mixing amount. Approxi-

mately 70% mixing

the up and

down

sides.

Exclusively

for

rotor

clockwise rotation.

The LOW side mixing amount from mid throttle (hovering point)

position is adjusted and down set with the side knob

The HIGH side mixing amount from mid throttle (hovering point)

position is adjusted and set with the up side knob

• The amount the of

revolution mixing

up side knob 1 1

and down side

knob 10 begins

individually set

from the neutral

position of the

HIGH

Fig. 2

Servo throw

by throttle

stick

throttle stick

Mixing is adjusted and

set over this range with

the revolution mixing

up side knob 11 .

.Throttle stick neutral

position

Mixing is adjusted and

set over this range with

the revolution mixing

down

side

knob®.

Throttle hold switch

When this switch is ON, the throttle servo the stops at position set

with trimmer and only the pitch the servo is controlled toy

throttle stick. It is used for auto rotation landings. When this, switch

is OFF, the throttle and are mixed. The pitch servos switch turn- is

ed on when pulled forward.

Throttle hold trimmer

Trimmer which

sets

the

throttle

servo stop

position

when the

throt-

tle hold switch is ON. Full travel setting is possible.

Idle up switch

When this switch is pulled forward, it is turned on the position and

set with the idle up trimmer on the back of the transmitter

becomes the maximum slow position of When the throttle servo.

this switch is set to OFF, the normal slow position of the stick be-

comes the maximum slow position of the throttle servo.

Power switch The upper position is ON.

Level meter This level meter indicates the transmitter battery voltage

Neck strap bracket Bracket for the neck strap (optional).

Antenna

Strong telescoping antenna. Extend it to when its full length using

the transmitter.

Handle Use this bar to transmitter. carry the

Nonslip adjustable lever head

The length of the lever head can be adjusted to fit the operator.

Transmitter NiCad battery NT-8LP

Adjust to your hand the length of

Lever head

in the arrow direction, and head adjust the to

the most comfortable length, then lock it by

turning it in the direction opposite the arrows.

Fig.

Neutral

elevator.

Idle up trimmer

This trimmer is effective

The idle up amount of

the throttle servo can

be adjusted and set

within this range with

FJ9. 6 the throttle up trimmer.

when the idle up switch

is ON. It adjusts and sets the

throttle hold maximum slow

position, and can be set as

shown in the ﬁgure.

Trimmer

is for the ailer-

on and trimmer

for the

Transmitter crystal

Aileron AST trimmer

Elevator AST trimmer

AST is the abbreviation of

Adjustable Servo Throw. The

servo throw can be adjusted

and set as shown in the fig-

ure.

Throw can be

adjusted and

set over this

range. 40% —

100%

Fig.

MAXIMUM

SLOW

Servo reversing switches

Using the servo reversing switches

• The side the left of each switch is normal position.

• The of the servo reversing switches reverse the direction operation of

servos.

Elevator serv servo Throttle o

reversing switch reversing switch

After linkage the is complete, inspect the servos. If direction of

operation of the stick lever and the direction of operation of a

servo are opposite, switch the appropriate servo reversing switch.

Battery cover

Remove this cover

when switching the

servo reversing

switches.

Remove the

battery

cover, by

pulling it in

the arrow

direction while

pressing

downward.

Fig.

NORM-> Normal

REV -> Reverse

Pitch

control

servo

reversing

switch

Rudder servo

reversing switch

Aileron servo

reversing switch

The tension of the adjusted. stick lever spring can be

Fig.

Charging jack

Battery charge jack for built-in NiCad battery.

•CHARGING OF

TRANSMITTER

AND RECEIVER

NI-CAD BATTERIES:

Battery Charger

Type FBC-8B(4)

Recharge the receiver and

transmitter NiCad batteries

as shown in Fig. 10.

Notes:

1) First, connect to TX NiCad

and red lamp goes on.

2) Then connect to RX NiCad

after connecting, L, E, D,

chanqes color from red to

• Connect the plug of charging the FBC-8B charge to the transmitter

charging jack, connect the 3P of connector the FBC-8B to the re-

ceiver NiCad battery (NR-4J), and plug the FBC-8B to a 117VAC

outlet as shown in this figure.

• The Receiver battery can be used about minutes 10 times at 10 per

flight between rechargings.

• Charge the batteries for about 15 hours. When in the set is not use for

some time, repeat discharge and charge two to three times before use.

(If the batteries not are used for a time, long their capacity will go

down).

• FBC-8B charges transmitter and receiver NiCad batteries independent-

ly or simultaneously.

Lever head

. by them turning

Unlock lever heads

and

Throttle stick deﬂection

HIGH

Pig.

(NR-4J)

greenish red (orange)

which indicates that

both TX and RX NiCads

are being charged.

3) In case separate of

charging

L, E, D, color will be:

RX NiCad - Green.

TX NiCad - Red.

Charging

plug

LED

Rx:

When adjusting the

aileron, and elevator

the inside module

is removed.

Use a small Phillips

screwdriver.

Elevator

Aileron

Rudder

When these screws are

removed, the back cover

can be removed.

• The tension of the

spring can be adjusted

by removing the trans-

mitter back cover and

turning the screw for

each stick. Set the

springs for the best

stick feel.

Product specificaties

Merk:	Futaba
Categorie:	Radiografisch bestuurbaar speelgoed
Model:	FP5NLH

Heb je hulp nodig?

Als je hulp nodig hebt met Futaba FP5NLH stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Radiografisch bestuurbaar speelgoed Futaba

Futaba 6EXA Handleiding

2 Juni 2023

Futaba FP2F Handleiding

23 Mei 2023

Futaba FP7UAFS Handleiding

21 Mei 2023

Futaba R3006SB Handleiding

17 Mei 2023

Futaba 9CPsuper Handleiding

7 Mei 2023

Futaba FP5UAP Handleiding

1 Mei 2023

Futaba 14MZ Handleiding

1 Mei 2023

Futaba 9ZHP Handleiding

1 Mei 2023

Futaba FP2L Handleiding

29 April 2023

Futaba R3004SB Handleiding

29 April 2023

Handleiding Radiografisch bestuurbaar speelgoed

Nieuwste handleidingen voor Radiografisch bestuurbaar speelgoed

Sky Rider DR392 Handleiding

25 April 2024

Spektrum Firma 130A Handleiding

13 Maart 2024

Spektrum Avian EF1 Handleiding

13 Maart 2024

Spektrum Firma 120A Handleiding

13 Maart 2024

Spektrum Firma 160A Handleiding

13 Maart 2024

Carson Amphi Power Truck Handleiding

12 Maart 2024

Spektrum A6390 Handleiding

12 Maart 2024

Spektrum A6380 Handleiding

12 Maart 2024

Spektrum S63 Handleiding

12 Maart 2024

Spektrum STL Handleiding

12 Maart 2024